得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual Cross-Network Gateway (Radio,VoIP,Public Announce) User Manual ROIP102 Series Version：1.0 2011-4-9 For environmental protection,please view this manual electronically and only print the pages you need - RoIP-102 - Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual Content I. Important Notices .............................................................................................. 3 II. Gift Box Check List ......................................................................................... 4 III. Overview ........................................................................................................ 5 IV. Installation ............................................................................
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual I. Important Notices i. This product is used to link up the civilian radio network,internet,and cellular phone network.Its operation and performance rely on the broadband network connections via private and/or public networks and the cellular phone networks.Due to the stability and reliability of these networks,this product may not be able to link up all the networks connected without any interruptions.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual II. Gift Box Check List Upon unpacking the gift box,please check carefully that all items listed below are included.Please report to your supplier for any missing items immediately. 1×PPT Adapter Cables 1×AC/DC Adapter Input:110/220 VAC Output:12VDC,2A 1×Main Unit 1×Ethernet Cable Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual III. Overview The fundamental of RoIP Radio over IP technology is to convert the audio and PTT signals in a radio terminal into IP packets and then transmit the data via the IP networks.The challenge in this technology is to insure that the audio is transmitted in real time and the PTT control signal is transmitted immediately and reliably.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual ii. Basic networking:multi-region over internet The diagram above demonstrates A to use with the conference system RoIP302M as a central switching point,the other three regions using RoIP102.Through this link,ABCD four areas to achieve multi-region interconnections among RoIP Series gateways. iii. Model Nomenclature Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual IV. Installation i. Back Panel Label 1 2 Name PTT1 Reote Switch 3 3 5 WAN LAN Power Description 6-pin RJ11 port for PTT Adapter Cable Relay switch with 220VAC input and 500 mA load current. 10/100Base-T WAN connection for external 10/100Base-T LAN connection 12V 1A ii.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual iii. Channel Port Pin Assignment The channel port is 6-pin RJ-11 Socket 1、 PTTOUT 2、GND 3、Vin（RX） 4、Aout（TX） 5、GND 6、PTTIN iv. PTT Adapter Cable wiring Diagram v. Switch Port The built-in relay switch is connected to the middle two pins of the RJ-11 socket.It acts as an ON/OFF switch for the external system connected. Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual vi. Main Unit Setup Connect the Channel Port to a Radio Channel via the PPT Adapter Cabel provided.Up to 1 channel is supported. Connect the WAN Port to a router,network switch,ADSL/Cabel Modem for access an external network or the public network. Connect the Switch Port to an external system fro remote control.It can be used to switch on and off a Public Announce (PA) system to instant broadcast.If the relay switch is connected to high voltage load.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual V. Default Factory Settings The table below shows the factory default settings.There are two way to reset to the factory default settings: i. Press the RESET switch for more than 15 seconds. ii. In the Configuration paga,select Tools and then Reset Config. Item Login ID Login Password Factory Default Settings admin admin WAN Port Setting LAN Port Setting PTT State DHCP 192.168.8.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual VI. Device Configuration Via Built-in Web Server The built-in web server provides a comprehensive way to fully program the device manually i. Web Server Login There are two methods to access the built-in web server. Method 1 is to access the built-in web server via the LAN port.Connect a computer to the LAN port of the RoIP102 and configure its IP to 192.168.8.x(x=2 to 254).Type the IP address 192.168.8.1 in the address field of a web browser.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual connection’s optimal environment is private network with static IP route,followed by a dyamic public IP,such as ADSL,Radio and TV network,under the shared router IP network is relatively unstable.If you must use the network shared line,strongly recommended the router set to DMZ to RoIP102 used IP. Setting up a network first used to confirm the network status,the general recommendation to use a fixed IP.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual www.device serial number.com。 Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual VII. Call settings i. Call Logic : RoIP can be connected between each other by SIP server as a proxy,can also be used independently by the way point to point.Because communication through the server will reduce efficiency and increase instability,it is strongly recommended to use the way point to point network.Therefore,this guide focuses on telling point is configured. ii.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual When registered successful after start up,the terminal will automatically calls the number corresponding to a connection. iv. PTT Settings： PTT setting is to determine each PPT input and output Active level RMS value.PTT settings determine each of the input and output RMS level,set “0” represents the effective interface potential efficient PTT is low,is set to “1” indicates that the PTT interface is high potential effect.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual viii. Public Announce (PA) Settings The RoIP302 provides a relay switch to control a PA system. When the RoIP302 receives the PA ON Password, it turns on the relay to activate the PA system. Audio is transmitted to the PA system at this time. When the RoIP302 receives the PA OFF Password, it turns off the relay to deactivate the PA system. The duration for the relay to be in the ON state is limited by the value set in the parameter PA ON Expiry.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual VIII. Application Examples Example 1: Linking up two MOTO GM300 Radio terminals in peer-to-peer mode with two RoIP102. The network access method is ADSL. Operating procedures: i. Connect the PTT Interface of the radio terminal (GM300) with the PTT Interface Cable as shown in the diagram below. Connect the RJ-11 plug of the PTT Interface Cable to PTT1 port of the RoIP102. ii. Connect the RoIP302 LAN port to an Ethernet port of the ADSL Router iii.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual GM300 in the PTT (COR) is low input and output RMS,so PTT settings are : A: set for the host,the number is set to 101,the body number is : ROIP2010060005,DDNS,and call setup is as follows: DDNS Settings Call Settings: B: body number ROIP20100610006,the DDNS and call settings is as follows： DDNS Settings Web: www.dbltek.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual where xxx in www.xxx.
得伯乐科技有限公司 DBL Technology Limited IX. RoIP-102 User Manual Hardware Specifications i. Physical and Operating Conditions - Dimension: 25 x 14 x 3 cm - Main Unit Net Wegith: 380 g - Storage Temperature: -40°C - 80°C - Operating Temperature: 0°C - 40°C ii. Core Design - CPU: ARM9 - RAM: 16MB - FLASH: 4MB - DSP: 116 MHz, 16 Bit Bus iii. T Interface - PTTIN Active Low: <0.7V (4.7KΩ load) - PTTIN Active High: >1.2V - PTTOUT High Output: 5V (4.
得伯乐科技有限公司 DBL Technology Limited RoIP-102 User Manual PTTOUT Cicuit: iv. Network Port -Ethernet Port:10/100 Base-T -Standard Supported:IEEE802.1p -IP Standard:IPV4 v. Firmware Item OS IP Voice Protocol Network Protocol Codecs Configuration GUI Description Remark Linux Version 2.6 SIP 2.0 Include SIP INFO extension IP、TCP、UDP、HTTP、ICMP、DHCP CL & SRV、NTP、 TFTP、ToS、telnet G.711 a&μ G.729A G.729AB G.723.1 GSM Html XML2.0 JAVA Web: www.dbltek.
