User's Manual

ManualsBrandsDbii Networks ManualsElectronicsMODULAR UNLICENSED NATIONAL INFORMATION INFRASTRUCTURE DIGITAL TRANSMISSION SYSTEM

Dbii Ltd, 16F-3, 482 Zhongxiao East Rd, Sec 5, Taipei 11083 Taiwan

Email: support@dbii.com Ph: +886.2.2346.3318, Fax: +886.2.2346.2751

www.dbii.com

OEM Instruction Manual

F52N-PRO is a high power miniPCI card to be used in outdoor wireless systems. Please follow

the following instruction while using this card. This card is meant to be operated (and used) by

system integrators who are aware of the regulatory requirements in the area it is being used.

The following instructions need to be followed while using the card

1) Before inserting the card in a host PC board, please power down the host PC board first

2) The antenna ports (MMCX connector) should be connected to the appropriate load or

antenna before powering up the host board. Lack of Antenna (or load) while the F52N-PRO is

powered up will cause severe damage to the card

3) Please make sure any person handling the card with bare hands follows proper ESD

precautions. Improper handling could cause ESD damage.

4) The card should not be tampered or modified in any way. Tampering or modification could

cause the card to fail standard test

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the interference by one of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

- Consult the dealer or an experienced radio/TV technician for help.

The use of any antenna (based on antenna design and gain) other than those certified with the

product voids authorization of this equipment and are expressly forbidden in accordance to FCC

rules CFR47 part 15.204. The OEM and installer shall configure the output power level based

on antenna selection, gain, and installation use (i.e. point-to-point or point-to-multipoint).

Guidance of power settings and antenna selection are included in this manual for reference.

Use of the lowest usable power level for each installation is recommended. This product may

NOT be sold to the general public as professional installation is required. OEM’s must ensure

installers of end product understand the requirements and limitations of the Authorization.

Professional installation is required of equipment with connectors to ensure compliance with

Summary of content (5 pages)

PAGE 1
OEM Instruction Manual F52N-PRO is a high power miniPCI card to be used in outdoor wireless systems. Please follow the following instruction while using this card. This card is meant to be operated (and used) by system integrators who are aware of the regulatory requirements in the area it is being used.
PAGE 2
health and safety issues. Below are the lists of antennas certified with this product. The OEM must ensure that end product complies with FCC labeling requirements. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate identifier for this product as well as the FCC notice below. This device complies with Part 15 of the FCC Rules.
PAGE 3
(B) A lower value for the directional gain than that calculated in paragraph (c)(2)(ii)(A) of this section will be accepted if sufficient evidence is presented, e.g., due to shading of the array or coherence loss in the beamforming. (iii) If a transmitter employs an antenna that operates simultaneously on multiple directional beams using the same or different frequency channels, the power supplied to each emission beam is subject to the power limit specified in paragraph (c)(2)(ii) of this section.
PAGE 4
5725-5850 MHz U-NII operations Maximum transmitter settings for fixed point-to-multi-point operation installation Antenna Model Gain (dBi) Channel Width(MHz) Software Max Power Setting Actual Max Tx Power Dipole USI05220170/2.5/5dBi 5 5,10,20 22 27 Omni 65812 ODN 12 5,10,20 22 27 Sector MA-WB55-20 20 5,10,20 22 27 Panel MA-WA55-30 30 5,10,20 15 20 Dish PX3F-52-N7 33.
PAGE 5
type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada.