User Manual

user manualuser manual
EnglishEnglishEnglish
21
EnglishEnglishEnglish
user manualuser manual
22
Perform the checks listed below:
- Check if the speaker is properly connected to the power supply.
- Make sure that the power supply is of correct voltage.
- Check that the amplifier is not overheated.
- Disconnect the speaker from the mains power supply, wait for a few minutes and
connect it again.
If after these tests the red “LIMITER” LED is still on, please contact an authorised service
centre.
LOUDSPEAKER INSTALLATION
WARNING
Make sure that the loudspeaker is securely installed in a stable position to avoid any
injuries or damages to persons or property.
For safety reasons do not place one loudspeaker on top of another without proper
fastening systems. Before hanging the loudspeaker check all the components for
damages, deformations, missing or damaged parts that may compromise safety during
installation.
If you use the loudspeakers outdoors avoid places that are exposed to bad weather.
The loudspeaker has the following mounting options:
- bookshelf (Fig. 1)
- floor (monitor) (Fig.2)
- on speaker stands (Fig.3)
- suspended with brackets supplied by the manufacturer (Fig.4)
WARNING
Never use the handles to hang the speaker!
R
OPE AR
OPE A
DD
BB
dd
H L
O
I
C
N
O G
E
E
T
S
H L
O
I
C
N
O G
E
E
T
S
B
B
d
d
H L
O
I
C
N
O G
E
E
T
S
H L
O
I
C
N
O G
E
E
T
S
d
d
B
B
H
OI
N E
T
O
L
G
EC
S
H
OI
N E
T
O
L
G
E C
S
OPER
A
OPER
A
D
D
B
B
d
d
T
O
O
I
S
C
E
H
L
E
N
G
T
O
O
I
S
C
E
H
L
E
N
G
B
B
d
d
T
O
O
I
S
C
E
H
L
E
N
G
T
O
O
I
S
C
E
H
L
E
N
G
d
d
B
B
N
O
TO
EHI E
SCG
L
N
O
TO
EHI E
SCG
L
TECHNICAL SPECIFICATIONS
OPERA 208 D OPERA 210D OPERA 410 D
Amp and processor
Power supply: Analog Analog SMPS
HF amp: Class-D 50 W/RMS Class-D 50 W/RMS Class-D 100 W/RMS
Bass amp: Class-D 150 W/RMS Class-D 150 W/RMS Class-D 300 W/RMS
Cooling: Convection, fan-free Convection, fan-free Convection, fan-free
System presets: Flat, Processed Flat, Processed Flat, Processed
Limiter: Peak,RMS, Thermal, limiters Peak,RMS, Thermal, limiters Peak,RMS, Thermal, limiters
Pre-Amp: 24bit 48KHz DSP 24bit 48KHz DSP 24bit 48KHz DSP
X-over frequency: 2050 Hz, 24 dB/oct. 2050 Hz, 24 dB/ oct. 1940 Hz, 24 dB/ oct
Audio Data
Frequency response -10 dB: 67 Hz - 20 kHz 62 Hz - 20 kHz 61 Hz - 20 kHz
Frequency response +-3 dB: 78 Hz - 19 kHz 71 Hz - 19 kHz 70 Hz - 19 kHz
Max SPL: 121 dB 122 dB 127 dB
Bass/midrange woofer: 1x8“ - 1,5“ voice coil 1x10“ - 1,5“ voice coil 1x10 - 2“ voice coil
High frequency driver: 1x1“ driver Neodymium 1x1“ driver Neodymium 1x1“ Compression driver 1,3” voice coil
Horn: 80°/65 x 60° CD Horn 80°/65 x 60° CD Horn 80°/65 x 60° CD Horn
Input section
Signal input/link: XLR fem. Balanced XLR fem. Balanced XLR fem. Balanced
XLR male balanced XLR male balanced XLR male balanced
6,3mm JACK balanced 6,3mm JACK balanced 6,3mm JACK balanced
Input sensitivity: -40dBu/-3dBu (Mic/Line) -40dBu/-3dBu (Mic/Line) -40dBu/-3dBu (Mic/Line)
Mains: IEC, VDE IEC, VDE IEC, VDE
Hardware
Pole mount: 36 mm 36mm 36mm
Handles: one on top one on top (rubber) one on top (rubber)
Angles up: 43° for monitor 43° for monitor 43° for monitor
Grille: 1,2mmm Metal with foam 1,5mmm Metal with foam 1,5mmm Metal with foam
Dimensions (W x H x D): 300 x 484 x 284 mm 343 x 553 x 304 mm 343 x 553 x 304 mm
Weight: 8,4 kg 9,8 kg 10,6 kg
Optional accessories: gig bag, mounting bracket gig bag, mounting bracket gig bag, mounting bracket