Operating instructions

On-Going Maintenance
1. Water maintenance .....
a. Add 1 oz of Stain & Scale to sequester metals and impurities once a week
b. Wait 15 minutes add
1
/
2
oz of Natural & Clear to remove oils once a week.
2. Balance your water ....
a. Check pH and Alkalinity and adjust as necessary
3. Sanitize your water ....
a. Check Bromine Level two to three times a week to insure a 2 - 4 ppm Bromine level
i. If Bromine levels are low
1. Add 4 oz Bromide Liquid Salts
2. Add 2 oz of Activator to Spa as a shock
Monthly Maintenance - Two-Part Bromide
Do your normal weekly maintenance and add Step 4.
4. Clean your spa
a. Wipe off your acrylic shell - clean off dust, water spots, chemical stains etc...
b. Clean and condition your cover - Remove dust, pollen dirt or snow - condition it to protect it from
the sun and cold
c. Clean your filters - Soak in cleaning solution, rinse thoroughly before using and dry. (You may have
to do this every other week if you use your spa more than four times a week.)
d. Check water in Spa fill Spa to half way mark of skimmer
Note: If you are using ThermOzone, you may try to reduce your sanitizer level to once weekly maintenance only.
You should maintain a 1 ppm Bromine level.
Water Maintenance
25
On-Going Maintenance
1. Water maintenance ....
a. Add 1 oz of Stain & Scale to sequester metals and impurities
b. Add 1/2 oz of Natural & Clear to remove oils
2. Balance your water ....
a. Check pH and Alkalinity and adjust as necessary
3. Sanitize your water ....
a. Check Bromine Level twice a week to insure a 2 - 4 ppm Bromine level
i. If Bromine levels are low
1. Open feeder to provide more Bromine to the spa
2. Add 2 oz of Activator to Spa as a shock
ii. If Bromine levels are high, close feeder by 1 - 2 holes to reduce bromine level.
iii. Add Tablets if necessary - Never add more than 2 tablets into dispenser at a time
Monthly Maintenance
Do your normal weekly maintenance and add Step 4.
4. Clean your spa
a. Wipe off your acrylic shell - clean off dust, water spots, chemical stains etc...
b. Clean and condition your cover - Remove dust, pollen dirt or snow - condition it to protect it from
the sun and cold
c. Clean your filters - Soak in cleaning solution, rinse and dry thoroughly before using. (You may have
to do this every other week if you use your spa more than four times a week.)
d. Check water in Spa fill Spa to half way mark of skimmer
Note: If you are using ThermOzone, you may try to reduce your sanitizer level to once weekly maintenance only.
You should maintain a 1 ppm Bromine level.
Spa Chemical Maintenance Program - Two-Part Bromide
What You Will Need
1 - WT1001 - Stain & Scale 1 - WT1003 - Natural & Clear
4 - SP1004 - Bromide Liquid Salts 1 - WB1002 - pH Alk Down
1 - WB1001 - pH/Alk Up 1 - SP1008 - Activator (Weekly Shock)
1 - TS1002 - Bromine Test Strip
Start Up (Please make sure all pump unions are tight)
1. Set up your water maintenance
a. All water comes with certain minerals and impurities. These chemicals help get your water
clear and ready for use.
b. Fill Spa to half way mark of skimmer
i. Add 3 oz of Stain & Scale.
ii. Wait 15 minutes add
1
/
2
oz of Natural & Clear.
c. Wait until water is above 80 degrees
2. Balance your water ....
a. Alkalinity and pH measure the acidity of your water. Step 2 helps you balance your water to prevent
skin irritation and corrosion of spa parts.
i. Test Alkalinity/pH with the test strips provided in your starter kit
1. Alkalinity should measure between 80 - 120
2. pH should measure between 7.2 - 7.8
ii. Adjust your Alkalinity first to the proper range
1. If adjustment is needed add 1 oz of Alkalinity/pH Up or Down to spa water.
2. Check Alkalinity after 15 minutes and adjust as necessary
iii. Check your pH next to balance water fully
1. If adjustment is needed add
1
/
2
oz of Alkalinity/pH Up or Down to spa water.
2. Check pH after 15 minutes and adjust as necessary
3. Sanitize your water ....
a. Sanitization keeps your water free of harmful bacteria, viruses and other organic matter that can
cause your water to be cloudy.
i. Add 8 oz Bromide Liquid Salts to water
ii. Wait 5 minutes and shock spa with 2 oz of Activator to start Bromine reserve.
Water Maintenance
24