Product data

ManualsBrandsDB Drive ManualsAmplifierSpeed Series Amplifier SPA SPA150.4

Page 17

Installation, Operation & Maintenance Manual (IOPCKKS60220510B1)

RECOMMENDED SAFETY PRACTICES

This publication explains the proper use and installation of equipment in order to warn operating and maintenance personnel of the

commonly recognized dangers associated with this equipment. In addition to following the manufacturer’s installation instructions, care

must be taken to ensure compliance with federal, state and local rules, regulations, codes and standards.

Ref to Harmonised procedure

UNI EN 12100-1& 12100-2

UNI E

N 12100-1& 12100-2

UNI EN 12100-1& 12100-2

Applicable standards of EEC Machinery Directive

Measures taken

1.1.1 Defination Referred in Instruction Manual

1.2.2 Control Devices

1.2.3 starting

1.2.4 stopping devices

1.2.4 a Emergency stop

1.1.2a,b,c,d,e,f

Principles of safety Integration

1.1.3 Materials and products

1.1.5 Desgin of machinery to facilitate its handling

1.2.1 Safety and Reliability of control system

1.3.4.Risks d

ue to surfaces, edges or angles.

1.3.7 Preventation of risks related to moving parts.

1.3.8 choice of protection against risks related to moving parts

1.4.1 General Requirements

1.2.6 Failure of the power supply

1.2.7 failure of the control circuit

1.2.8 Software

1.3.2 Risk of breakup during operation

1.7.2 warning of residual risk

1.7.3 Marking

1.4.2.1 Fixed Gurards

1.5.1 Electricity supply

1.5.4 Error

of fittings

1.5.8 Noise

For Start/Restart, Voluntary actuation required for change of

temperature settings, Machine doesn’t have several starting

controls

Refer to Electrical schematic pasted inside the unit, Normal

stoppi

ng can be activated by main disconnect switch, its in

customer scope

1.5.9 Vibration

1.6.1 Machinery maintenance

1.6.2 Access to operating position and servicing points

1.6.3 Isolation of energy sources

1.6.4 Operator intervention

1.6.5 Cleaning of internal part

1.7.1 Warning devices

Failure o power supply will stop the machine, once power is

restored, voluntary actuation is required t

o restart.

Machine doesn’t start without manual interaction, stop has got

priority over

start

Refer to IOM for details of Simplicity Programming

Refer to page 7 of IOM, + 10% voltage fluctuation limit specified

Refer to "

safety considerations

" in Instruction Manual

Refer to Instruction manual

Design of unit with basement for lifting by forklift or rope, locking

of compressor fixings during transport

ustomer's scope, Loop for emergency stop is provided in

Electrical schematic

Refer to

Electrical schematic pasted inside the unit

control devices are positioned outside danger zone, Emergency

stop to be provided by customer, loop for same provided &

Described in IOM

Refer to IOM

Refer to page 19 of Instruction Manual

Refer to Unit dimensional drawing in IOM

Refer to IOM

operating conditions

stated on the as built drawings, frequency of

maintenance listed in the instruction m

anual, Fixed guards are

provided so that breakage will be contained.

covers will be put on sharp edges of screws

Refer to IOM for Noise data

access door openable with special tools , written warnings fitted

on access door.

Marking on metal name plate displayed on the outside fan

section access door & on control pan

el door

I t ll ti d i t h db k A b ilt d i

Refer to IOM for warning Notes

Work instruction of safety procedures manual

Refer to maintenance schedule in IOM

Written warning in proximity to electrical and rotating pars, loops

for warning devices is provided refer to wiring schematic

UNI EN 12100-1&

12100-2