Owner Manual

3
Preparing site foundations
Important: Ensure selected position has sufficient
clearance on all sides considering maximum string
drying length or required space.
Retractable Clothesline Mounting Kit Installation
To install vertical post
1. Mark recommended position and excavate a hole
250–300mm (10-12 inches) square x 450mm (1.5 feet)
minimum depth.
2. Prepare a wet damp pre-mix concrete,
approximately 10kg, and backfill the hole 250–
300mm (10-12 inches) from ground level.
INSTALLATION INSTRUCTIONS
4. Prepare remaining pre-mix concrete to a wet
damp mix and backfill the hole level to the
ground.
5. Ensure post is vertical on both sides using a
spirit level (adjust cords as required).
6. Allow 3 days to cure concrete before installing
crossbar.
To install crossbar
1. Position steel bracket between vertical post
and crossbar.
Note: Crossbar side with middle recess must
be facing out.
2. Place M8x124mm bolt in the middle of
the crossbar, through the steel bracket and
the vertical post, then affix nut and tighten
into position.
Retractable Clothesline Mounting Kit
Installation
To install vertical post
1. Mark recommended position and excavate a
hole 250–300mm square x 450mm minimum depth.
2. Prepare a wet damp pre-mix concrete,
approximately 10kg, and backfill the hole
250–300mm from ground level.
3. Place vertical post into the hole in upright
position with plastic cap facing upwards and
tie each length of cord onto 3 equally spaced
stakes on the ground.
Preparing site foundations
Important : Ensure selected position has
sufficient clearance on all sides considering
maximu
m string drying length or required space.
Recommended height position of line from
ground level to crossbar mounting hole is
user height + 100mm
Maximum wall/post to post distance of 7.0 metres.
4. Prepare remaining pre-mix concrete to a wet
damp mix and backfill the hole level to the
ground.
5. Ensure post is vertical on both sides using a
spirit level (adjust cords as required).
6. Allow 3 days to cure concrete before installing
crossbar.
To install crossbar
1. Position steel bracket between vertical post
and crossbar.
Note: Crossbar side with middle recess must
be facing out.
2. Place M8x124mm bolt in the middle of
the crossbar, through the steel bracket and
the vertical post, then affix nut and tighten
into position.
Retractable Clothesline Mounting Kit
Installation
To install vertical post
1. Mark recommended position and excavate a
hole 250–300mm square x 450mm minimum depth.
2. Prepare a wet damp pre-mix concrete,
approximately 10kg, and backfill the hole
250–300mm from ground level.
3. Place vertical post into the hole in upright
position with plastic cap facing upwards and
tie each length of cord onto 3 equally spaced
stakes on the ground.
Preparing site foundations
Important : Ensure selected position has
sufficient clearance on all sides considering
maximu
m string drying length or required space.
Recommended height position of line from
ground level to crossbar mounting hole is
user height + 100mm
Maximum wall/post to post distance of 7.0 metres.
Daytek 6-line Retractable hole position (811mm/31.93”)
Wattle 6-line Retractable hole position (737mm/29.02”)
Daytek 5-line Retractable hole position (681mm/26.81”)
Daytek 4-line Retractable hole position (551mm/21.69”)
Wattle 6-line Hand Rail position
Daytek 5-line Hand Rail position
Daytek 4&6-line Hand Rail position
Center line
112.5mm (4.43”) 112.5mm (4.43”)
295mm (11.61”)
355mm (13.98”)
425mm (16.73”)
464mm (18.27)
Figure 2 Outdoor Retractable Clothesline and Hand Rail hole positions
3. Place vertical post into the hole in upright position
with plastic cap facing upwards and tie each length
of cord onto 3 equally spaced stakes on the ground.
4. Prepare remaining pre-mix concrete to a wet damp
mix and backfill the hole level to the ground.
5. Ensure post is vertical on both sides using a spirit
level (adjust cords as required).
6. Allow 3 days to cure concrete before installing
crossbar.
Recommended height position of line from ground
level to crossbar mounting hole is user height +
100mm (4 inches).
Maximum wall/post to post distance of 7.0 meters
(23.0 feet).