S T R I D E R NURSING PFLEGEBETTEN BEDS OPERATING MANUAL MD 4 Plus Order number: E1-04-058-001
Strider MD 4 Plus Introduction With the Days Healthcare Strider, you have now purchased a product which has been manufactured in accordance with the newest technical capabilities and based on the highest operating comfort. We have placed great value on the simplest possible operation and long service life in both construction and material selection. A large variety of useful accessories rounds off our range in addition to the Strider.
Strider MD 4 Plus Contents 1.0 Safety instructions ................................................................................. 8 1.1 Symbols used .............................................................................. 8 1.2 Intended use ................................................................................ 8 1.3 General Information ..................................................................... 9 1.4 Safety when driving .........................................................
Strider MD 4 Plus 8.0 9.0 10.0 11.0 12.0 13.0 Contents 7.5.1 Preselecting the drive level ............................................. 38 7.5.2 Adjusting the speed ........................................................ 38 7.6 Before driving ............................................................................ 39 7.7 Driving ....................................................................................... 39 7.8 Brakes .....................................................................
Strider MD 4 Plus 14.0 15.0 16.0 17.0 Contents 13.2 Transporting the complete strider ............................................... 51 13.3 Preparation for transport - separating component ....................... 52 13.3.1 Working step summary ................................................... 52 13.3.2 Removing the seat .......................................................... 52 13.3.3 Removing the rear panelling ............................................ 53 13.3.4 Removing the batteries ......
Strider MD 4 Plus 18.0 19.0 20.0 21.0 Contents 17.6 Batteries .................................................................................... 83 17.6.1 Disposal of used or damaged batteries ........................... 83 17.6.2 Refitting battery cables ................................................... 84 Temporary storage ........................................................................... 85 Appendix .........................................................................................
Strider MD 4 Plus Safety information 1.0 Safety instructions 1.1 Symbols used This instruction manual contains the following symbols which are used to highlight special hazards in dealing with the product or information for simplifying the handling. Caution! This symbol identifies safety information which notifies you of hazards when dealing with the product. NOTE You will also find information about dealing with the product under this symbol. 1.
Strider MD 4 Plus 1.3 Safety information General Information Read the entire operating manual thoroughly before using the Strider! Ensure that: • the operating manual is read by all people who drive, care for and service the scooter. • all persons who drive, care for, service or repair the scooter have access to the operating manual at any time. Any damages resulting from nonobservance of this operating manual are excluded from the guarantee.
Strider MD 4 Plus 1.4 Safety information Safety when driving Risk of accidents! • Check correct functioning of the brakes and lighting unit (indicators, headlights) before every journey. • Always use lights when visibility is restricted, either by day or by night. • Check the tyre air pressure regularly. • Always use the seat belts when driving. • Do not switch the scooter off while driving. • Do not drive up or down gradients which are too steep, over obstacles on gradients or up and down ramps.
Strider MD 4 Plus Safety information Danger due to unintentional movement! • Always turn the scooter off using the keyswitch if you: - want to get on or off - intend to stop for long periods - you are putting the scooter away. 1.
Strider MD 4 Plus 1.6 Safety information Safety when handling batteries Fire hazard! • Do not cover the battery charger and ventilation slot while charging batteries. • Only use the battery charger in well-ventilated rooms. Risk of accidents! • Only use the original battery charger (included in delivery). • Let your dealer replace your battery. • Only use batteries as detailed in the chapter entitled “Specifications”. • Observe warning information given by the battery manufacturer.
Strider MD 4 Plus Versions 2.0 Extent of delivery After receiving your Strider, please check the following: • that the delivery is complete in accordance with the list below • the delivery condition using the inspection plan (chapter 15.3) If any faults are apparent or components are missing, please contact Days Healthcare or your medical supplier. The following items are included in delivery in addition to the Strider: 1. Shopping basket 2. Two vehicle keys for switching the Strider on 3.
Strider MD 4 Plus Components 3.0 Components 3.1 The Strider Dashboard with controls Rear view mirror Speed switch Seat unit with headand armrests Tiller Shopping basket Drive unit covers Indicators and rear light Indicators and headlight Steering wheel 3.2 The dashboard - displays and controls Brake lever for handbrake Operation indicator (fault display) Handle Drive lever (reverse) 14 Issued: 28.02.
Strider MD 4 Plus Brief instructions 4.0 Brief instructions The following brief instructions should enable people to quickly get used to operating the scooter after a long period of non-use and to refresh existing knowledge of operation. It is imperative that you follow the instructions given in the main manual! 4.1 Driving the Strider NOTE Before starting driving, adjust the seat height, the backrest and the armrests to a comfortable position. Your specialist dealer would be very glad to help. 1.
Strider MD 4 Plus Brief instructions 3.) Fasten the seat belt. ON 4.) Switch on the Strider 5.) Check the battery charging state 16 Issued: 28.02.
Strider MD 4 Plus Brief instructions 6.) Adjusting the drive level H = 12 kph (8 mph) maximum driving speed L = 6.4 kph (4 mph) maximum driving speed 7.) Set the maximum speed = lowest possible driving speed = highest possible driving speed 8.) Driving Operate the drive lever slowly until the required speed has been reached Ma The drive lever position controls the x. d d rivi pee speed variably right up to maximum ng gs n i spe driving speed. riv ed x. d Ma 1 Reverse Forwards 17 Issued: 28.02.
Strider MD 4 Plus 9.) Braking = release drive lever (1) 10.) Direction indicators (1) Horn (2) Hazard lamps (3) Lights (4) 18 Issued: 28.02.
Strider MD 4 Plus 4.2 Brief instructions Transporting the Strider Dismantling the Strider (stages 1 to 10) 1.) Remove the seat 2.) Remove the rear panelling 3.) Remove the lighting cable 4.) Separate the front connector 5.) Remove the battery plug 19 Issued: 28.02.
Strider MD 4 Plus Brief instructions 6.) Remove the battery belts and batteries 7.) Fold the tiller down 8.) Unlock the drive unit 9.) Tilt the drive unit away 10.) Remove the chassis Reassembling the Strider (Stages 10 to 1) 20 Issued: 28.02.
Strider MD 4 Plus Adjusting the seat height 5.0 Setting up the Strider The following passage describes how to set up your Strider in order to ensure that you have a comfortable and safe drive. 5.1 Adjusting the seat height NOTE! The seat must be removed from the Strider in order to adjust the seat height. You should try to get help from a second person if possible or contact your dealer. Tilt the backrest forwards Removing the seat: ➨ Tilt the backrest forwards.
Strider MD 4 Plus Adjusting the seat height ➨ Press the locking device on the plug and disconnect the electric cable connecting plug (5) to the rear lights and rear indicators. ➨ Remove the rear panelling. Adjusting the seat height: Tools required: 1 x Allen key (size 6 mm) Adjusting the seat support The seat height (h) is adjusted by using the holes in the seat support. ➨ Loosen the upper clamping bolt (6). ➨ Loosen the lower clamping bolt (7) and pull the it out of the seat support (8).
Strider MD 4 Plus Adjusting the seat height Fixing the rear panelling: Connecting the light cable ➨ Plug in the light and indicator cable connecting plug (5). Fixing the rear panelling ➨ Place the rear panelling onto the drive unit from above. While doing this: - Introduce the engaging lever (a) into the appropriate hole. - Engage the rear panelling onto the mountings (b) on the drive unit. - Align the rear panelling to the strider chassis (c).
Strider MD 4 Plus Adjusting the seat position Tilt the backrest backwards: ➨ Pull the locking lever (1) and move the backrest backwards to the required position (2). Tilt the backrest backwards ➨ Let go of the locking lever and engage the locking mechanism by pushing the backrest slightly forwards and backwards. 5.2 Adjusting the seat position 5.2.1 Adjusting the distance between seat and tiller ➨ Pull the locking lever (1) upwards and move the seat forwards or backwards to the required distance.
Strider MD 4 Plus Adjusting the seat position 5.2.3 Adjusting the armrest height Loosening the fixing Tools required: 1 x Allen key (size 5 mm) ➨ Loosen the Allen screw (4) and remove. The armrest height is adjusted using four holes in the armrest support (b). The height can be adjusted in stages of 10 mm. ➨ Pull the armrests upwards to the required Adjusting the armrest height height until the hole in the armrest support appears through the hole in the seat tube (5).
Strider MD 4 Plus Adjusting the seat position 5.2.4 Adjusting the backrest inclination The backrest inclination can be adjusted in three locking stages. 1st stage = drive setting 2nd stage = drive setting 3rd stage = not for driving! Tipping hazard! • Only adjust the seat adjustment to the third position when the vehicle is not travelling! ➨ Pull the locking lever (6) and move the backrest forwards or backwards to the required position (7).
Strider MD 4 Plus 5.4 Adjusting the seat position Adjusting the tiller angle Always adjust the tiller so that you can reach all displays and controls easily at any time. The tiller can be variably adjusted. adjusting the tiller ➨ Push or pull the locking lever (1). ➨ Push the tiller forwards or backwards into the required position. ➨ Release the locking lever. ➨ Ensure that the tiller is engaged correctly by moving it backwards and forwards.
Strider MD 4 Plus Driving information 6.0 Information about safe Strider driving Always carry out the safety information described in chapter 1.5 “Safety during driving“! Driving the Strider is very simple and after a few practice sessions you will find it very easy. The following information should help you to drive safely through traffic: • always match your speed to the driving situation in which you find yourself.
Strider MD 4 Plus Driving information Climb angle examples: a 1 metre long ramp should not be higher than 18 cm a 2 metre long ramp should not be higher than 36 cm • Avoid driving across an incline (always try to drive in the direction of the incline / decline).
Overcoming obstacles The Strider can climb over obstacles such as kerbstones up to height of 8 cm without any problem.
Strider MD 4 Plus Driving information 6.2.1 Driving Information – Overcoming kerbs Risk of accidents! Neogating kerbs needs some practice. • Please observe the maximum obstacle heights of 8 cm. • Please start practicing kerb climbing with small kerbs. Approach at a right angle ➨ Approach the kerb at a right angle. Stop in front of the kerb ➨ Stop approximately 0.5 Meter / 19 inches in front of the kerb. Adjust the speedcontroller ➨ Adjust the speed controller to maximum speed.
Strider MD 4 Plus 6.3 Driving information Overload protection - motor protection The overload protection system switches the drive off if the motor becomes overloaded by trying to climb over too high an obstacle such as a kerbstone, or if you try to climb to steep an incline. Should the overload protection system activate, the motor or power module has overheated. This can be caused by driving up long inclines with high load and/or under high environmental temperatures.
Strider MD 4 Plus 6.4 Driving information Battery charging state = driving range 6.4.1 Battery charging state Battery charge display Battery charge display: The battery charger display on the dashboard shows the battery charging state.
Strider MD 4 Plus Driving information 6.4.2 Driving range The Strider driving range is dependent on the following conditions in addition to battery charge: - landscape conditions (level or steep) - weight of user - weather conditions (cold, rain) - driving with headlights For this reason, information about the driving range is only given as a guideline. The more experienced you are in using the Strider, the easier it will be for you to determine the driving range using the battery charging state.
Strider MD 4 Plus Driving the Strider 7.0 Driving the Strider 7.1 Getting on and off Please observe the following before getting on or off: • The Strider must be standing on firm, level and non-slippery ground. • The engaging lever for push mode must be in the drive position (see chapt. 9.0). • Turn the Strider off and remove the key. Turning the seat • Tilt the steering column forwards (see chapt. 5.4.). • When getting in and out, ensure that your clothing does not get caught on the drive lever.
Strider MD 4 Plus Driving the Strider NOTE! If you feel you are safe enough, you can of course get onto the Strider without turning the seat round. • You can lift up the armrest on the side where you are standing and then get on. 7.2 Seat belt adjusting for length and putting on Adjusting for length: ➨ Turn the seatbelt closer (1) at right angles to the seat belt. Adjusting for length Adjust the length by pulling the appropriate belt side.
Strider MD 4 Plus 7.3 Driving the Strider Turning the seat The seat can be turned to both sides of the angle, and firmly engaged in 8 positions (each position turns 45°). Turning the seat: ➨ Pull the turning lock (1), turn the seat in the required direction or position (2) and engage. Accident hazard due to incorrect seat position! • Always turn the seat to face forwards and engage it before driving. If the seat has been turned, the possibility of tipping is increased.
Strider MD 4 Plus 7.5 Driving the Strider Adjusting the speed NOTE Use the adjustment facilities to adjust the speed to suit local conditions. Select a lower speed if you are driving through narrow gaps, on inclines or through crowds. 7.5.1 Preselecting the drive level You can use the drive level selection switch to set the maximum driving speed.
Strider MD 4 Plus 7.
Strider MD 4 Plus 7.8 Driving the Strider Brakes 7.8.1 Using the motor brake Motor brake ➨ Let go of the drive lever (1). The drive lever stops in the central position - the Strider uses the motor to brake. Emergency braking = let go of the drive lever! The drive lever automatically returns to the central position if you let go. The Strider automatically brakes using the motor. 7.8.2 Using the handbrake ➨ To use the handbrake, pull the brake lever (2) slowly towards the handlebar.
Strider MD 4 Plus Driving the Strider 7.10 Switching on the headlights Pressure switch (4): Switching on the headlights ➨ switch on = press switch once ➨ switch off = press switch again The switch indicator lamps shows whether the headlight is switched on or not. NOTE If you drive with the headlights on, the Strider driving range will be considerably reduced. 7.11 Using the horn ➨ Press the horn button (5). Using the horn It will sound for as long as you hold the button down. 7.
Strider MD 4 Plus 8.0 Hazard lamps Pressure switch (6): ➨ switch on = press switch once ➨ switch off = press switch again The switch indicator lamps shows whether the hazard lamps are switched on or not. NOTE • Leaving the Strider with the hazard lamps on uses up the battery. The driving range will be reduced! 42 Issued: 28.02.
Strider MD 4 Plus Pushing the Strider 9.0 Pushing the Strider Disengaging the drive In order to be able to push the Strider, you must disengage the drive motor. The disengaging lever (1) is located on the right-hand side of the Strider. No one is permitted to sit on the Strider when it is being pushed. = Pushing (a): ➨ Switch off the Strider. ➨ Pull the engaging lever (1) upwards as far as the stop (limit position).
Strider MD 4 Plus Charging the batteries 11.0 Charging the batteries Please also see the information given in the chapter entitled “Things to know“. Charging information: • The surrounding temperature should be between 10° and 30° Celsius. The charging time will increase at lower temperatures. • Only use the original battery charger (included in delivery). • Only use the battery charger in a dry and well-ventilated room. • Do not cover the battery charger and ventilation slot while charging batteries.
Strider MD 4 Plus Charging the batteries 11.2 Charging the batteries ➨ Switch the Strider off. ➨ Engage the engaging lever for push mode into the “drive“ position. It is imperative that you observe the sequence for connecting and disconnecting the battery charger. Switching off Engaging Connecting the battery charger The jack socket (3) for connecting the battery charger is located on the left of the tiller. ➨ (1.) Connect the battery charger plug (4) to the Strider charging socket. ➨ (2.
Strider MD 4 Plus Charging the batteries LED information at battery charger during charging: LED -> Colour -> Meaning (a) -> Red (b) -> Yellow -> charging in progress LED -> battery charger switched on -> Green -> charging complete, battery completely charged 11.3 After charging ➨ Switch the battery charger off at the toggle switch (6). ➨ (1.) Switch off and Remove the battery charger plug from the mains socket.
Strider MD 4 Plus Things to know 12.0 Things to know 12.1 The battery charger - functioning principle The battery charger regulates the voltage (Volt) and the current (Ampere) from your mains connection down to the voltage required for charging your batteries (24 Volt). The amount of charging current required is dependent on the charging state of the discharged batteries.
Strider MD 4 Plus Things to know 12.3 The auto switch-off The auto switch-off automatically switches the Strider off after 20 minutes at a standstill. This protects the batteries from being discharged if the Strider was inadvertently not switched off. 12.
Strider MD 4 Plus 12.7 Lighting Things to know Lighting The lighting is composed of two groups: a front headlight and direction indicator (4) and the rear light and direction indicator (5). Anti tipping wheels 12.8 Anti tipping wheels The anti tipping wheels reduce the danger of tipping during extreme manoeuvres when fixed to the rear of the Strider. It is not permitted to drive the Strider without anti tipping wheels. Wheels and tyres 12.
Strider MD 4 Plus Things to know 12.10 Brakes on the strider 12.10.1 The motor brake The Strider is automatically braked if the drive lever (1) is in the central position. To apply the brakes, simply let go the drive lever which is then returned to its central position by a spring. The Strider is then braked by the drive motor. When the Strider is at a standstill or has been switched off, it is braked by a magnetic brake. Drive lever 12.10.
Strider MD 4 Plus Transporting the Strider 13.0 Transporting the strider 13.1 Transport information Depending on the size of the transport vehicle, the Strider can be dismantled in a few steps so that it can also be easily transported in smaller vehicles. When transporting, take particular care to ensure that the batteries are securely fastened and make sure components cannot tip over. No liability can be accepted for damage caused by transportation. 13.
Strider MD 4 Plus 13.3 Preparation for transport - separating component Clamping and crushing hazard! Increased hazards due to clamping or crushing result due to the high component weight (such as batteries) during preparation for transport. • Always carry out any work to be done with great care. • Always try to get help from a second person, especially when stowing parts for transport. In just a few steps you can dismantle the Strider down to the following components to make it ready for transport: 1.
Strider MD 4 Plus Transporting the Strider Removing the seat ➨ Lift the seat while pulling the seat lock (3) out of the seat support (4). 13.3.3 Removing the rear panelling Removing the rear panelling ➨ Pull the rear panelling off the Strider upwards. ➨ Press the locking device (A) on the plug and disconnect the electric cable connecting plug (5) to the rear lights and rear indicators. ➨ Remove the rear panelling. 53 Issued: 28.02.
Strider MD 4 Plus Transporting the Strider 13.3.4 Removing the batteries Removing the batteries ➨ Press the locking device on the plug and disconnect the connecting plugs (6 + 7) on the battery cable. ➨ Remove the battery belts (8). ➨ Remove the batteries. 13.3.5 Folding the tiller down Folding the tiller down ➨ Push or pull the locking lever (9) and fold the tiller to the rear (10) until it is horizontal. 13.3.
Strider MD 4 Plus Transporting the Strider Unlocking the drive unit ➨ Open the clamping bolt clamping lever (15) and fold the clamping bolt upwards. Tilt the drive unit away ➨ Tilt drive unit to the rear onto the anti tipp wheels (16). Separating the chassis ➨ Remove the frames (11) upwards from the holding bolts (12) on the drive unit. NOTE Use rear bumper as grip to stowe the drive unit. 55 Issued: 28.02.
Strider MD 4 Plus Transporting the Strider 13.4 After Transport - Reassembly Working step summary: ➨ Re-couple the drive unit. ➨ Fold the tiller up again. ➨ Insert the batteries and secure with the straps. ➨ Fit the rear panelling in place. ➨ Fit the seat. NOTE • All cable connection plugs can only be reconnected in one position (anti-rotation protection). • When re-connecting the plugs, ensure that the locking device engages correctly. 13.4.
Strider MD 4 Plus Transporting the Strider NOTE The clamping bolts fit automatically into the chassis receptacle (4). If this is not the case, the clamping bolts will have to be adjusted. You can find information about adjustment in the chapter 17.3.1. ➨ Close the clamping lever (5) on the clamping bolt down. Locking the drive unit NOTE The clamping tightness should be set so that the clamping lever can be closed by hand without requiring too much force.
Strider MD 4 Plus Transporting the Strider 13.4.3 Reinserting the batteries ➨ Place the batteries in the frame so that the battery terminal is facing inwards. Reinserting the batteries ➨ Route the safety straps (9 + 10) across the batteries as illustrated in the photograph and tighten. Plug in the battery plugs ➨ Plug in the battery cable connecting plugs (11). 13.4.4 Fixing the rear panelling ➨ Plug in the light and indicator cable connecting plug (12). 58 Issued: 28.02.
Strider MD 4 Plus Transporting the Strider Fixing the rear panelling ➨ Place the rear panelling onto the drive unit from above. While doing this: - Introduce the engaging lever (a) into the appropriate hole. - Engage the rear panelling onto the mountings (b) on the drive unit. - Align the rear panelling to the strider chassis (c). 13.4.5 Fitting the seat ➨ Pull the seat lock (14) and guide the seat Fitting the seat into the seat support (15) from above.
Strider MD 4 Plus Cleaning 14.0 Cleaning NOTE • Do not use any sharp-edged tools such as knives, metal scrapers or aggressive solvents for cleaning. • Do not use high-pressure cleaners to clean the vehicle. • Only use mild detergents without scouring agents to clean any surfaces. • Please observe instructions for use on the detergents to avoid damage to the component surfaces. • Never direct water jets onto the fittings on the tiller or drive unit components.
Strider MD 4 Plus Maintenance and Inspection 15.0 Maintenance and Inspection If you find any faults on your scooter during maintenance which are not covered by the repair information, please contact your dealer. Always remove faulty scooters from operation and secure them against unauthorised use (remove key). 15.1 Daily maintenance before start of journey ➨ Check the brakes by driving slowly and then braking. ➨ Check that the lights and indicators are functioning correctly.
Strider MD 4 Plus Maintenance and inspection 15.3 Annual inspection - inspection timetable Take your scooter once per year to your dealer for an inspection. He will have the necessary tools and experience to service your scooter correctly.
Strider MD 4 Plus Maintenance and inspection Description (Component / inspection for) Assessment OK Defective Component : Tiller Panelling / no damage fixed securely Grip rubbers / no damage fixed securely Tiller, folding mechanism / no play in joint functions easily ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ Component : chassis Connections / no damage ❐ ❐ Frames / no damage ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ no corrosion Reflectors / no damage Steering mechanism / no damage no play in
Strider MD 4 Plus Maintenance and inspection Description (Component / inspection for) Assessment OK Defective Component : Handbrake Handbrake / all components no damage safe function equal adjusted both sides easy movement bowdencable ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ Component : Displays and controls, electric system, electronic system Dashboard switches / no damage safe function Dashboard displays / no damage safe function Indicator lamps / no da
Strider MD 4 Plus Maintenance and inspection Description (Component / inspection for) Assessment OK Defective Component : Displays and controls, electric system, electronic system Drive lever/ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ ❐ (Scooter can not be pushed) ❐ ❐ no damage functions easily ❐ ❐ ❐ ❐ lever engaged (lever remains engaged) ❐ ❐ No damage Easy functioning over the entire lever movement Returns to central position after releasing from any position Secure blockage of magnetic brakes whe
Strider MD 4 Plus Troubleshooting 16.0 Troubleshooting 16.1 Before troubleshooting Before you start troubleshooting, please observe the following points to prevent errors coming into the process. ➨ Switch the Strider off. ➨ Check the main plug (1) and the battery plug (2) for a tight fit. ➨ Switch the Strider on again. If the fault occurs again, you will find information about troubleshooting and fault remedy in the following lists. 16.
Strider MD 4 Plus Fault Cause Remedy Scooter does not run Check battery charge display (battery discharged). Charge the batteries (chapter 11.0) Strider switched to push mode Switch to drive mode (chapter 9.0) Drive lever pressed while switching on Release drive lever Fault on drive lever Visit your dealer Automatic switchoff (overload protection) active Switch the electromobile off and switch it on again a few seconds later. Operation indicator blinking Check blink code (chapter 16.
Strider MD 4 Plus Troubleshooting Fault Cause Remedy Lighting / indicators not working Scooter not switched on Switch the scooter on (chapter 7.4) Power supply interrupted Check the battery fuses (chapter 17.5.2) Check front unit and battery connecting plug (chapter 13.4.1 / 13.4.3) Batteries do not charge Switch defective Visit your dealer Check fuse in power supply to tiller head Replace fuses (chapter 17.5.1) Defective fuse in battery cable Replace fuses (chapter 17.5.
Strider MD 4 Plus Troubleshooting 16.3.1 Blink codes Fault Cause Remedy Operation indicator blinking (fault display) ... ... blinking slowly when switching on Drive lever Release drive lever pressed down while switching on ... blinking slowly during the journey Battery voltage too low Finish your journey as soon as possible and charge the batteries ... blinking slowly, scooter does not run Check battery charge display (Batteries discharged) Charge the batteries (chapter 11.
Strider MD 4 Plus Repairs - mechanics 17.0 Repairs The following repair information should enable you to carry out small repairs on your vehicle yourself. You should, however, only carry out such work if you are used to working with the tools described here since it is impossible to fully prevent injury hazards when handling tools. If you are not sure, you should try to get help from a second person if possible or contact your dealer.
Strider MD 4 Plus Repairs - mechanics 17.3 Mechanics 17.3.1 Adjusting the drive lock clamping bolts The clamping tightness is adjusted by turning the clamping bolts. The clamping tightness should be set so that the clamping lever can be closed by hand without requiring too much force. Tools required: 1 x screwdriver; Phillips head No. 2 Unlocking the clamping lever Adjusting the clamping tightness: ➨ Unlock the clamping lever (1). ➨ Adjusting the clamping bolts: (1.
Strider MD 4 Plus Repairs - mechanics ➨ Checking the clamping bolt setting. Checking the setting It must: • automatically fall into the chassis receptacle (3). • be able to be locked by hand without use of great force (4). ➨ Checking the clamping lever alignment. Checking alignment The clamping lever (5) must be inclined slightly to the right (around 1 o’clock) when locked. Tightening the locking screw ➨ Tighten the locking screw (6). 72 Issued: 28.02.
Strider MD 4 Plus Repairs - mechanics 17.3.2 Wheels - removal and replacement Tools required: 1 x socket spanner, size 19 mm Removing the wheels: ➨ Remove the wheel fixing protective cap (1) with a screwdriver. Removing the wheels: Front wheel ➨ Loosen the self-locking nut (2) for the wheel fastening (size 19 mm). ➨ Secure the Strider against rolling away. ➨ Lift the Strider and support it (see chapter 18.0). ➨ Remove the self-locking nut for the wheel fastening (size 19 mm).
Strider MD 4 Plus Repairs - mechanics Fitting the front wheel: Fitting the front wheel ➨ Push the wheel onto the stem (3) as far as the wheel stop. ➨ Screw the wheel fixing self-locking nut (4) and tighten it (size 19 mm). ➨ Lower the Strider. ➨ Retighten the self-locking nut. ➨ Press the protective cap onto the wheel fixing nut. Fitting the rear wheel: ➨ Place the key (5) in the slot in the drive shaft (6). Locating the axle key NOTE The key is rectangular.
Strider MD 4 Plus Repairs - mechanics Locating the washer ➨ Place the washer (8). Securing the rear wheel ➨ Screw the wheel fixing self-locking nut (9) and tighten it (size 19 mm). ➨ Lower the Strider. ➨ Tighten the self-locking nut. ➨ Press the protective cap onto the wheel fixing nut. 75 Issued: 28.02.
Strider MD 4 Plus Repairs - mechanics 17.3.3 Replacing the inner tube / tyre ➨ Remove the damaged wheel. Deflating the tyres ➨ Unscrew the valve cap (1). ➨ Carefully press the valve plunger (a) inwards with a screwdriver until the inner tube is completely deflated. Risk of accidents! • Dismantle the wheel rims only when the inner tube is completely deflated. Dismantling the wheel rims: ➨ Loosen the three nuts (2) with a socket spanner (size 12 mm) and remove together with the lock washers (3).
Strider MD 4 Plus Repairs - mechanics 17.3.4 Adjusting the handbrake at the handlebars. ➨ Secure the Strider against rolling away. ➨ Raise the side with the braked wheel and support (see Chapter 18.0). Before adjusting the brake, check that the handle adjustment (1) is screwed fully in. If this is not the case, then: ➨ turn the locknut (2) until this contacts the adjusting screw (3). ➨ Turn the adjusting screw until it contacts the handle.
Strider MD 4 Plus Repairs - mechanics Checks after adjustment: The following points must be checked after brake adjustment, and adjustments must be repeated until the brake functions correctly. • uniform brake effectiveness on both front wheels when braking from movement (see chapter 7.8.2). • Braking wheel free running when brake not applied. Checking free running: ➨ Rotate the braking wheel.
Strider MD 4 Plus Repairs - lighting 17.4 Lighting Tools required: 1 x screwdriver; Phillips head No. 2 17.4.1 Replacing bulbs in headlights and rear light Bulb version used: 24 V / 5 Watt (glass base lamp) Removing the lamp lens NOTE The working sequence for front and rear indicators is the same, and is described using photographs of the rear lights. ➨ Loosen the fixing screw (1) and remove the front or rear light lens. Removing the bulb ➨ (1.) Pull the bulb out of the lamp holder.
Strider MD 4 Plus Repairs - lighting 17.4.2 Replacing bulbs in front/rear indicators Bulb version used: 24 V / 10 Watt NOTE The working sequence for front and rear indicators is the same, and is described using photographs of the rear lights. Removing the lamp lens (Example: rear light) ➨ Loosen the fixing screw (1) and remove the front or rear light lens. ➨ Remove the bulb: (1.) Press the bulb in lightly and remove by turning 1/8 turn to the left. Removing the bulb (2.
Strider MD 4 Plus 17.5 Fuses Repairs - fuses Wiring diagram 17.5.1 Strider Fuses A wiring diagram with fuse sizes is located on the control unit cover. The Strider is fitted with the following fusible fuses. (1) 2 A fuse = power supply to tiller head (2) 10 A fuse = Light (3) 10 A fuse = charging socket To replace Fuse: ➨ Open fuse holder. ➨ Pull out fuse and replace it. ➨ Close fuse holder. 81 Issued: 28.02.
Strider MD 4 Plus Repairs - fuses 17.5.2 Battery Fuses 2 types of battery fuses are used. Battery fuse: type 1 Type 1: • 70 A fuse = strip fuse Fuse holder in the plus pole cable of the batteries To replace Fuse: ➨ Unscrew fuse housing. ➨ Pull out fuse holder. ➨ Loosen both clamping screws (1, SW 4 mm) of the strip fuse. ➨ Replace fuse strips (2) and tighten clamping screws. ➨ Screw together fuse housing.
Strider MD 4 Plus Repairs - batteries 17.5.3 Battery charger fuse • 10 A fuse (1) 17.6 Batteries Only replace the batteries with the following battery types: 12 V / 38 Ah - 20h (32 Ah - 5H), liquid acid deep cycle batteries Max. battery size (l x w x h) = 197 x 165 x 170 mm You may not*use wet cell batteries with detachable cover caps. Risk of accidents! • Refitting the battery may only be carried out by your dealer. 17.6.
Strider MD 4 Plus Repairs - batteries 17.6.2 Refitting battery cables Fire and burns hazard if battery terminal is short-circuited! • Never touch both battery terminals simultaneously with tools (shorting out). • Terminals are protected with insulating caps. Only ever remove the insulating cap from the terminal which you are going to loosen. Tools required: 2 x ring spanner; size 10 mm ➨ Remove the batteries from the Strider as described in chapter 13.3.4.
Strider MD 4 Plus Temporary storage 18.0 Temporary storage If you are not intending to use your Strider for longer periods (e.g. over the winter, you should prepare it as follows: Front support, ➨ Remove soiling and dust. ➨ Charge the batteries completely. ➨ Check the tyre pressure and adjust if necessary. ➨ Place the Strider on supports. Lift the Strider high enough so that the tyres are no longer touching the floor.
Strider MD 4 Plus Appendix - specifications 19.2 Specifications 19.2.1 General data Strider application class (internal and external use) ........................... Typ B Version ........................................................ 4-wheel version Turning radius .............................................. 156 cm Speed .......................................................... 12 kph (8 mph) Maximum range* ......................................... approx. 21 Miles Maximum climable incline .........
Strider MD 4 Plus Appendix - dimensions 19.2.2 Dimensions 87 Issued: 28.02.
Strider MD 4 Plus Appendix - tightening torques 19.3 Torque for fixing screws Front wheel central self-locking Nut (M10*p1.25) = 50 Nm Rear wheel central self-locking Nut (M12*p1.25) = 60 Nm Front / rear wheel rim, 3 nuts (M8*p1.25) = 33 Nm General torque for nuts and bolts: M5 = 4.5 to 6 Nm M6 = 8 to 12 Nm M8 = 18 to 25 Nm M10 = 30 to 40 Nm M12 = 50 to 60 Nm 19.
Strider MD 4 Plus Warranty 20.0 Warranty information The Strider Model MD 4 scooters carry a 12 months warranty from date of purchase. Important! • During the warranty period any parts that have become defective due to faulty workmanship or material will be repaired or replaced without charge by Days Healthcare supplier / dealer. • The warranty excludes tyres and all items that have been subject to undue wear and items subjected to misuse.
Strider MD 4 Plus 21.
DAYS HEALTHCARE LTD North Road Bridgend Ind Est Bridgend CF31 3TP Tel: 01656 664700 Fax: 01656 664750
