User Manual

ManualsBrandsDay-Brite CFI ManualsRemote ControlDay-Brite CFI 911401855781 Motion Sensor Remote Control

www.day-brite.com www ome3/24/2022 2

1.Press button, the remote LED indicators will show the latest paramete

2.Long press button 3-5 seconds until the brightness indicator light is on

4.Aim at the target sensor and press to upload the new paramete

3.Press button to select daylight lux.

5.Aim at the target sensor and long press to turn off daylight sensor fun

• Remove the batteries from compartment if the remote will not be used in 30 days.

ON/OFF Switch Mode(the sensor is disabled)

Sensor Configuration

1. Press button to show latest configurations.

2. Press “BRIGHTNESS”,“HOLD TIME”,“STANDBY DIM”,“STANDBY TIME”,“SENSITIVITY”,“DAYLIGHT” button to select new parameters.

3. Aim at the luminaire and press button to upload new parameters. The luminaire will flicker ON and OFF once as confirmation.

Daylight Function Configuration

rs.

r. The luminaire will flicker ON and OFF once as confirmation.

Performance (Daylight Priority Mode)

The light switches on at

100% when there is

movement detected.

The light dims to stand-by

level after the hold-time.

When the natural light

level exceeds setpoint

off to light,the light will

turn off even if when the

space is occupied.

The light automatically turns

on at 10% when natural

light is insuffcient (no

motion).

The light remains in dimming

level at night.

Settings on this demonstration:

Hold-time: 30min

Stand-by Dim: 10%

Stand-by time:

(Daylight priority mode: the stand-by time is only ,otherwise is

daylight threshold mode.)

Note:

1.Daylight Priority Mode: the illuminance value to turn on/off the lamp automatically

controlled by the photocell

2.Daylight Threshold Mode: the illuminance value to turn on the lamp when detected

motion controlled by the photocell at each gear are: 10lx,30lx,50lx,100lx.

at each gear are: 10lx/50lx, 30lx/100lx, 50lx/150lx, 100lx/200lx.

Note:

1. Press any button to light up the indicator on the remote , and then press the "SEND" button, The luminaire will flicker ON and OFF once as confirmation.

Note: if there is no operation within 10 seconds, the indicator on the remote will be turned off automatically.

2. ON/OFF Switch Mode: Except for the "ON/OFF", "BRIGHTNESS", and "SEND" buttons, the other buttons will be disabled. Long press "ON/OFF" button

3-5 seconds to quit switch on/off mode (switch to the sensor sensing mode.)

3. TEST Sensitivity Mode: Except for the "TEST", "SENSITIVITY", and "SEND" buttons, the rest of the buttons will be disabled. Press the "TEST" button

again to quit this mode.

4. HB03R IR Remote, can not pass through walls and other opaque materials, please make sure that there is no object blocking between the remote

and the sensor when using.

5. HB03R is designed without waterproof function, please avoid long-term placement in damp environment when using.

1. Long press button 3-5 seconds until the brightness indicator light is on(first-row).

2. Switch on mode, press button to select new parameters.

3. Aim at the luminaire and press button to upload new parameters. The luminaire will flicker ON and OFF once as confirmation.

4. Aim at the luminaire and press button to turn off or turn on the fixture.

5. Aim at the luminaire and long press button 3-5 seconds to quit on/off switch mode. The luminaire will flicker ON and OFF once as confirmation.

ction.

Brightness: 100%

Daylight: 30lxSensitivity: 100%

10 30 50 100

SEND

Remote Control

Motion Sensor Remote Control

Motion Sensor Remote Control for LED High Bay Light

www.day-brite.com www ome3/24/2022 1

Dimensions

Power

0.1W

Power supply

2xAAA 1.5V battery,

Alkaline perferred

Upload Range

Up to 15m(50ft.)

Op. Temperature

0℃~50℃

12NC

911401855781

Description

Button Operation

140.4mm

50.4mm

17.6mm

LED Indicators

Button Description

LED Description LED Description LED Description

Button Description Button Description

Long Press the button 3-5 seconds until

the brightness indicator light is on,then pr-

ess button, the light goes to permanent

on or permanent off mode, and the sensor

is disabled.

(MUST long press button to quit on/off

switch mode for setting.)

Press button to adjust hold time:10s/

HOLD TIME

BRIGHTNESS

STANDBY DIM

DAYLIGHT

STANDBY TIME

RESET

SENSITIVITY

1min/10min/30min.

Press button to adjust stand-by

dimming level:10%/20%/30%/50%.

Press button to adjust occupancy

sensing sensitivity:20%/50%/75%/100%.

High end trim turning function(To

Set the output level of connected

lighting during occupancy).

The time that the Sensor will dim the

light to a low level after the area is

vacated.

To represents the time that the

sensor will keep the light at low dim

level after the HOLD TIME elapsed.

To represents various thresholds of

natural light level for the sensor.

To set the occupancy sensing sensitivity

of the Sensor.

To set the output level of connected

lighting during vacancy. The sensor

will regulate the lighting output at

the set level.

Short press or long press button to

adjust the brightness of the lamp in the

range of 0%-100%.

Note:After power-off, the brightness of the

lamp brightness returns to the correspond

-ing percentage of 70%/80%/90%/100%

set last time.

Press button to adjust brightness

level: 70%/80%/90%/100%.

Every change needs to Press button,

upload the current

the LED light which the sensor connects

will on/off as confirm.

Note:when the indicator light is on,the pro-

-gram can be sent only after button is

pressed.

Press button to adjust stand-by

Long press button 3-5 seconds until

the indicator

is on,then

press button to adjust daylight lux:

10lx/30lx/50lx/100lx.

Press button , the remote control will

restore the lowest gear ,brightness:70%,

hold time:10s,stand-by dim:10%,stand-by

Short press or long press button to

adjust the brightness of the lamp in the

range of 100%-0%.

Note:After power-off, the brightness of the

lamp brightness returns to the correspond

-ing percentage of 70%/80%/90%/100%

set last time.

The button is for testing purpose

sensitivity only. After you choose sensitivity

thresholds, then you press button,the

sensor goes to test mode(hold time is only

3s) automatically ,meanwhile the stand-by

time and daylight sensor are disabled.

Press button to quit from this mode.

parameters to sensor(s),

SEND

10 30 50 100

HCY-REMOTE control

BRIGHTNESS

DAYLIGHT

SENSOR

STAND-

BY TIME

SENSITIVITY

STAND-

BY DIM

HOLD TIME

Summary of content (2 pages)

PAGE 1
Remote Control Sensor Configuration Motion Sensor Remote Control 1. Press button to show latest configurations. 2. Press “BRIGHTNESS”,“HOLD TIME”,“STANDBY DIM”,“STANDBY TIME”,“SENSITIVITY”,“DAYLIGHT” button to select new parameters. 3. Aim at the luminaire and press Motion Sensor Remote Control for LED High Bay Light SEND button to upload new parameters. The luminaire will flicker ON and OFF once as confirmation. ON/OFF Switch Mode(the sensor is disabled) 1.
PAGE 2
Télécommande Configuration du capteur Télécommande avec détecteur de mouvement 1. Appuyez sur le bouton pour aﬃcher les dernières conﬁgurations. 2. Appuyez sur le bouton "LUMINOSITÉ", "TEMPS DE MAINTIEN", "DIM EN VEILLE", "TEMPS EN VEILLE", "SENSIBILITÉ", "LUMIÈRE DU JOUR" pour sélectionner de nouveaux paramètres. 3. Visez le luminaire et appuyez sur le SEND bouton pour télécharger de nouveaux paramètres. Le luminaire s'allumera et s'éteindra une fois en guise de conﬁrmation.