User`s guide

ManualsBrandsDAVIS ManualsAutomotiveTrip 500AL

Product #8104 SmartCard On-Board Reader

Product #8108 SmartCard Desktop Reader

Product #8112 SmartCards, Pack of 10

Product #8116 Starter Interrupter Kit

Product #8119 Adapter Kit for DriveRight Trip 500AL

DriveRight

SmartCard System

User’s Guide

DriveRight SmartCard System User’s Guide

Rev. A, April 2004

Products # 8104, 8108, 8112, 8116, and 8119

Document part number: 07395.191

Information in this document subject to change without notice.

DriveRight

is a registered trademark of Davis Instruments Corporation.

Velcro

is a trademark of Velcro Industries, Manchester, NH.

Summary of content (8 pages)

PAGE 1
DriveRight ® SmartCard System User’s Guide © Davis Instruments Corp. 2004. All rights reserved. DriveRight SmartCard System User’s Guide Rev. A, April 2004 Product #8104 SmartCard On-Board Reader Products # 8104, 8108, 8112, 8116, and 8119 Product #8108 SmartCard Desktop Reader Document part number: 07395.191 Product #8112 SmartCards, Pack of 10 Information in this document subject to change without notice.
PAGE 2
Technical Support If you are experiencing problems with your SmartCard equipment, first check the cable connections and verify the settings. If you are unable to solve the problem, please call Davis Technical Support. We’ll be glad to help. Most questions can be answered on the phone. You can also e-mail us for support, or visit our website. Sorry, we are unable to accept collect calls. ❏ (510) 732-7814 — Monday through Friday, 7:00 am to 5:30 pm, Pacific Time. ❏ (510) 670-9589 — Fax to Technical Support.
PAGE 3
Contents Starter 60 Amp Solenoid Starter Power Key Switch Introduction 12V Ignition Switch Wire In-Line Splice Butt Splice Green Wire SmartCards . . . . . . . . . . . . . . . . . . . 4 Correct Insertion Configuring SmartCards Additional Cards Green Wire On-Board Reader . . . . . . . . . . . . . . 5 Components Installation & Wiring Operation . . . . . . . . . . . . . . . . . .
PAGE 4
The SmartCard System This manual gives installation and operating instructions for five products in the SmartCard system: To disconnect the old 4-pin connector, pull back the housing on the male connector to release the lock. When you push the connectors together, the housing on the male connector slides back when you make the connection and the cables lock together.
PAGE 5
Adapter Kit for DriveRight Trip 500AL This optional equipment is needed to use a DriveRight Trip 500AL model with the SmartCard system. Components. Your DriveRight Trip 500AL Adapter Kit, product #8119, should come with the components shown below: Digital Input Cable Serial Data Cable (download cable) Desktop Reader. Connects to a PC at the office via USB port. Works in conjunction with the DriveRight Fleet Management Software, which reads and writes to the SmartCard.
PAGE 6
SmartCards Clock Adjustment. If you notice that the DriveRight console has incorrect time or Correct Insertion. When sliding SmartCard into the On-Board Reader or Desktop Reader, be sure the memory chip on the card is facing up as shown: date, its clock can be adjusted using the SmartCard. The administrator configures the card to add or subtract minutes (see the Fleet Management software manual).
PAGE 7
Sleep Mode. To conserve power, the On-Board Reader goes into sleep mode automatically. During sleep the unit is idle, not powered down; the starter circuit is still enabled. The Reader draws only about 15% as much power during sleep as opposed to regular operation with the indicator light on. On the DriveRight 600, with auto logout OFF and the vehicle stationary, the unit goes to sleep in about 10 minutes. Download is triggered before going to sleep if a card is inserted.
PAGE 8
To remove the connectors, hold both cables by their connector housings and pull apart. The housing of the male connector slides to release the lock and allow the cables to be separated. To connect cables, hold the female connector and push the male connector from behind, allowing its housing to slide back. When you make connection, the cables lock together. To connect cables, hold as shown here: To disconnect cables, hold as shown here: Sliding Connector Housing On-Board Reader Operation: Login.