Specifications
DM562AP
Operation Manual & AT Command Set
Integrated Data/Fax/Voice/Speakerphone Modem
12
Preliminary
Version: DM562AP-MA-P01
February 2, 2004
&W1 Stores active configuration profile in
configuration profile 1.
&Yn Selection of the Active Configuration After
Power-On or Reset.
&Y0* Retrieves configuration profile 0 as the active
configuration profile when the Modem is turned
on or is reset.
&Y1* Retrieves configuration profile 1 as the active
configuration profile when the Modem is turned
on or is reset.
&Zn=x Store Telephone Numbers in Nonvolatile
Memory. Stores three telephone numbers, 31
characters each, in the non-volatile memory.
Uses ATDS=n to dial or to use AT&M2 for
synchronous data mode.
*Gn Adaptive Handshake Selection.
*G0 Disables adaptive protocol handshake.
*G1* Enables adaptive protocol handshake.
*Nn Connect Speed Selection.
*N0 Selects connect speed 1200bps.
*N1 Selects connect speed 2400bps.
*N2 Selects connect speed 4800bps.
*N3 selects connect speed 7200bps.
*N4 Selects connect speed 9600bps.
*N5 Selects connect speed 12000bps.
*N6 Selects connect speed 14400bps.
*N7 Selects connect speed 16800bps.
*N8 Selects connect speed 19200bps.
*N9 Selects connect speed 21600bps.
*N10 Selects connect speed 24000bps.
*N11 Selects connect speed 26400bps.
*N12 Selects connect speed 28800bps.
*N13 Selects connect speed 31200bps.
*N14 Selects connect speed 33600bps.
*N15 Selects connect speed 1200/75bps.
*N16 Selects connect speed 300bps (V.21).
*N17 Selects connect speed 300bps (Bell 103).
*N19* Selects connect speed V.90 33333bps
*N22 Selects connect speed V.90 37333bps
*N25 Selects connect speed V.90 41333bps
*N26 Selects connect speed V.90 42666bps
*N27 Selects connect speed V.90 44000bps
*N28 Selects connect speed V.90 45333bps
*N29 Selects connect speed V.90 46666bps
*N30 Selects connect speed V.90 48000bps
*N31 Selects connect speed V.90 49333bps
*N32 Selects connect speed V.90 50666bps
*N33 Selects connect speed V.90 52000bps
*N34 Selects connect speed V.90 53333bps
*N35 Selects connect speed V.90 54666bps
*N36 Selects connect speed V.90 56000bps
*Qn Auto Retrain Selection.
*Q0 Disables auto retrain.
*Q1* Enables auto retrain.
*Xn Transmission Level Selection.
*X0* Selects output level -11dBm.
*X1 Selects output level -12dBm.
*X2 Selects output level -13dBm.
*X3 Selects output level -14dBm.
*X4 Selects output level -15dBm.
*X5 Selects output level -16dBm.
*X6 Selects output level -17dBm.
*X7 Selects output level -18dBm.
*X8 Selects output level -19dBm.
*X9 Selects output level -20dBm.
*X10 Selects output level -21dBm.
*X11 Selects output level -22dBm.
*X12 Selects output level -23dBm.
*X13 Selects output level -24dBm.
*X14 Selects output level -25dBm.
*X15 Selects output level -26dBm.
V.42bis / MNP Command Set
%An Set Auto-Reliable Fall Back Character
Set auto-reliable fall back character to n (n = 0
to 127).
%Cn Data Compression.
%C0 Disables data compression.
%C1* Enables data compression.
\An MNP Block Size Selection.
\A0 Selected 64-character maximum block size.
\A1 Selected 128-character maximum block size.
\A2 Selected 192-character maximum block size.
\A3* Selected 256-character maximum block size.
\Bn Set Line Break.
Send a n/10 seconds line break to the modem
(n = 0 to 9). Default = 3. Break length always
300 msec for MNP mode.
\En Normal Mode Data Echo Selection.
\E0* Disables data echo during a normal link.
\E1 Enables data echo during a normal link.