Manual

1. POOL TEMP (default setting, set temp and clock on text lines)
2. SET TEMP (clock and pool temp on text lines)
3. CLOCK (set temp and pool temp on text lines)
4. CYCLING (cycles through the above views 1 – 3 for 10 seconds each)
Page25
7.8.2MainDisplay
TheSP1200touchpadLCDconsistsoftwolinesoftextandfournumericaldigits. Thedisplaytypicallyshowsthree
quantities-pooltemperature,settemperatureandtheclock(weekdayandtime).Bydefaultthepooltemperatureis
displayedonthenumericaldigitsleavingtheclockandsettemperatureonthetwolinesoftext.
Ifpreferred,theusermaychangethelayoutsoeitherthesettemperatureorclockareshownonthemaindisplay
(fournumericaldigits)ratherthanonthesmallertextlines.Inadditionacyclingmodecanbeselectedwherebyeach
ofthethreepossibleviewsispresentedfor10secondseach.
Availableoptions:
7.8.3ChangingTheMainDisplay
1) SelecttheMISCOPTIONSsubmenufromthemainmenu.
2) SelecttheMAINDISPLAY menuitem
3) PresstheSCROLL buttontobeginmaindisplayselection.
4) UsetheUP andDOWNbuttonstosetthedesiredview.
5) PresstheSCROLL buttontoconfirmthecurrentsettingandreturntotheMISCOPTIONSsubmenu.
7.8.4PanelLightColourAndIntensity
Theuserhastheabilitytochangethetouchpadbacklightcolourandintensitytotheirpreferredsettings.Notethat
thesemanualsettingswillonlytakeeffectwheneitherthepoollightisofforifthe “panelandpoollight
synchronisation” optionhasbeendisabled
7.8.5ChangingTheTouchPadBacklightColour
7.8.6ChangingTheTouchPadBacklightIntensity
1) SelecttheMISCOPTIONSsubmenufromthemainmenu.
2) SelectthePANEL LIGHT INTENSITY menuitem.
3) PresstheSCROLL buttontobeginlightintensityadjustment.
4) UsetheUP andDOWNbuttonstosetthelightintensity.
5) PresstheSCROLL buttontoconfirmthecurrentsettingandreturntotheMISCOPTIONSsubmenu.
Pleasenotethatthebacklightintensitysettingonlyhaseffectwhenthepoolisinuse. After90minutesoftouchpad
inactivity(nobuttonpresses)thebacklightintensitywillautomaticallyreturntoafixed34%setting. Thisistoensure
longlifeofthebacklightLEDs. Assoonasyoupressabuttononthetouchpadyourcustomsettingwillberestored.
1) SelecttheMISCOPTIONSsubmenufromthemainmenu.
2) SelectthePANEL LIGHT COLOURmenuitem
3) PresstheSCROLL buttontobeginlightcolourselection.
4) UsetheUP andDOWNbuttonstosetthedesiredcolour.
5) PresstheSCROLL buttontoconfirmthecurrentsettingandreturntotheMISCOPTIONSsubmenu.
Push1 (PumpOn)
Push2 (PumpOff)
Push3 (Pump Auto)
Push1 (PumpOn)
Push2 (PumpOff)
Page8
3.4Pump1A&1B (Singlespeedpumps,no24hrcirculationpumpfitted)
ThreepushesofthePump1A buttoncyclesthepumpasfollows:
LCDdisplays “PUMP ON”,buttonLEDsgreen.
LCDdisplays “PUMP OFF”,buttonLEDsoff.
LCDdisplays “PUMP AUTO”,buttonLEDsgreen.
Notes:
1) IfPump1A isleftin”PUMP ONor “PUMP OFF” modes,thispumpwillautomaticallyrevertto “Auto” modeafter90
minutes.
2) Iftheheaterelementison,runningthepumpmaycausetheheatertoloadshedandswitchoff.Ifthisoccursthe
TwopushesofthePump1Bbuttoncyclesthepumpasfollows:
LCDdisplays “PUMP ON”,buttonLEDgreen.
LCDdisplays “PUMP OFF”,buttonLEDoff.
Notes:
1) IfPump1Bislefton,thispumpwillautomaticallyswitchoffafter25minutes.
2) Iftheheaterelementison,runningthepumpmaycausetheheatertoloadshedandswitchoff.Ifthisoccursthe
heaterwillcomebackonapproximately5secondsafterthepumpisdeselected.
3.5Pump1A&1B (Singlespeedpumps,24hrcirculationpumpfitted)
TwopushesofthePump1A buttoncyclesthepumpasfollows:
LCDdisplays “PUMP ON”,buttonLEDgreen.
LCDdisplays “PUMP OFF”,buttonLEDoff.
LCDdisplays “PUMP ON”,buttonLEDgreen.
LCDdisplays “PUMP OFF”,buttonLEDoff.
Notes:
1) IfPump1A orPump1Bislefton,thesepumpswillautomaticallyswitchoffafter25minutes.
2) Iftheheaterelementison,runningthepumpmaycausetheheatertoloadshedandswitchoff.Ifthisoccurs
theheaterwillcomebackonapproximately5secondsafterpumpisdeselected.
TwopushesofthePump1Bbuttoncyclesthepumpasfollows:
Push1 (PumpOn)
Push2 (PumpOff)
Push1 (PumpOn)
Push2 (PumpOff)