User's Manual
C
ha
p
t
e
r
3
I
n
s
t
a
ll
a
t
i
on
This
c
ha
p
t
e
r
describes how
to
i
ns
t
a
ll
the
OM5P-AN.
It
also describes
the
OM5P-AN
L
E
D
s
.
Only experienced
installation
professionals who are familiar
with
local building and
s
a
f
e
t
y
c
ode
s
a
nd,
wherever applicable, are licensed by
the
appropriate
g
ov
e
r
n
m
e
n
t
r
e
g
ul
a
t
or
y
a
u
t
h
or
i
t
i
e
s
should
i
ns
t
a
ll
the
OM5P-AN
.
3.1
P
r
e
-
i
n
s
t
a
ll
a
t
i
o
n
G
u
i
d
e
li
n
e
s
S
e
l
e
c
t
the
optimal
l
oc
a
t
i
ons
for the
equipment
using
the
following
g
ui
de
li
n
e
s
:
-
T
he OM5P-AN should be
mounted
on
a
1"-4"
pole.
I
t
s
l
oc
a
t
i
on
should enable easy access
to the
unit
and
i
t
s
c
on
ne
c
t
or
s
for
installation and
t
e
s
t
i
ng.
-
The higher
the
pl
a
c
e
m
e
n
t
of the
a
n
t
e
n
na
,
the better the
achievable link
quality.
-
The
a
n
t
e
n
na
should be
i
ns
t
a
ll
e
d
to
provide a direct,
or
near line
of
s
i
g
h
t
with the
Base
S
t
a
t
i
on
a
n
t
e
nna
.
The
a
n
t
e
nna
should be aligned
to
face
the
general
direction
of the
Base
S
t
a
t
i
on.
3.2
I
n
s
t
a
lli
n
g
the
OM5P-AN
To
i
ns
t
a
ll
the
OM5P-AN, use
the
following procedure
to
mount
the
device on a pole and refer
to
the
figure
below.
1.
The
bottom of the
OM5P-AN is a movable cover. Grab
the
cover and
pull it
back hard
t
o
remove
the cover.
2.
I
ns
e
r
t
a
s
t
a
nda
r
d
E
t
h
e
r
n
e
t
cable
into the
R
J
-
45
port
labeled MAIN
L
AN
.
3.
S
li
de
the
cover back
to
seal
the bottom of the
OM5P-AN
.
4.
Remove
the
power cord and
PoE
injector
from the
box and plug
the
power cord
into the
DC
port of the
PoE
injector.
Only use
the
power adapter supplied
with the
OM5P-AN. Using a
different power
a
da
p
t
e
r
might
damage
the
OM5P-AN
.
5.
Plug
the other
side
of the
E
t
he
r
ne
t
cable
in
s
t
e
p
3 into the
PoE
port of the
PoE
injector.
When you
f
i
ni
s
h
s
t
e
p
5,
the
installation
will
resemble
the
following
picture.
6.
Turn over
the
OM5P-AN. Then
i
ns
e
r
t
the
m
a
s
t
s
t
r
a
p
through
the
middle hole
of the
OM5P-AN
.
Use a screw driver
to
unlock
the
pol
e
-
m
oun
t
i
ng
ring putting
it
through
the
OM5P-AN
.
7. Mount the
EOA200 securely
to the
pole by locking
the
s
t
r
a
p
tightly.
This
c
om
pl
e
t
e
s
the
installation
procedure.