Contents Warranty ........................................................................................................................................................3 Disposal.........................................................................................................................................................3 Packing List...................................................................................................................................................
Warranty Standard Warranty • Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of purchase. • The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty. • Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this warranty. • All mail or transportation costs including insurance are at the expense of the owner.
Packing List 1 x SE-2200 Main Unit 1 x SE-2200 Control Panel / Keyboard 1 x SE-2200 Quick Start Guide 1 x Accessory List Connection of SE-2200 Use D-SUB Cable to connect SE-2200 main unit to SE-2200 control unit.
Main Unit – Front Panel The front panel on the SE-2200 main unit has a grille for airflow cooling fans. Please do not block or cover this grille as the unit may overheat. This grille should also be kept free of dust. The front panel can be removed by using the four thumbscrews. A soft brush or cloth can then be used to clean the grille before attaching it back to the unit. The power button starts and shuts down both the SE-2200 main unit and its attached keyboard.
Rear Panel Connections Video Input Modules The SE-2200 is equipped with six video input channels. Video Input set is comprised of six SDI connectors and two HDMI ports. The last two channels (#5 and #6) can be switched between SDI connector and HDMI port, i.e. the user is allowed to use CH5 and CH6 for either a SDI source or an HDMI source. Note: The CG (picture and animation) data source via HDMI cable connect to the SE-2200 channels 5 and 6. Can edit CG function from the PC.
Grounding Terminal When connecting this unit to any other component, make sure that it is properly grounded by connecting this terminal to an appropriate point. When connecting, use the socket and be sure to use wire with a cross-sectional area of at least 1.0 mm2. DC Input Connect the supplied 12V 3A PSU to this 4pin XLR socket. Pin 1 = GND ( - ) Pin 2 = NC Pin 3 = NC Pin 4 = VCC ( + ) Mini Switch 2 Firmware upgrade switch (The two DIP switches must be set to the UP position).
Control Panel 1. MSCR PGM 2. PC Control 3. Audio Fixed 4. Cross Point 5. Audio Follow Video 6. Menu Control 7. Transition Selection 8. F1~F4 (TBD) 9. PIP Selection PVW & PGM 10. DSK Selection PVW & PGM 11. Logos 1, 2, & Clock 12. 13. 14. 15. 16. 17. 18. 19. 20. 21.
Keyboard Controls Program and Preset rows The Program row of buttons is the active channel, this is the live output. The active channel will appear as the Program Output. You can switch or CUT from one video source to another directly on the Program row. You will see the multi view Program output change as you press different keys along this top row of buttons. The Preset row is the cued channel; this channel will appear in the Preview window.
FS – Frame Store Button The SE-2200 CH1~6 video channels, each of these channels has its own Frame Store. Each of these Frame Stores can hold one still image. This still image can be called into the production by using the FS button located at the top left corner of the SE-2200 Control Panel / Keyboard. The FS button allows the user to toggle between the still image of the Frame Store or the live video input also connected to that same video channel. How to choose live video input or Frame Store 1. 2. 3.
Audio Follow Video Manual selection of one audio channel fixed to one video channel at your choice. When you select video Channe1, the audio source and the video source will be synchronized on Channel 1. Please see the AUDIO FOLLOW VIDEO (Page 23) for more details. Menu Control Press the MENU button in the SE-2200 function section to enter the System Configuration Menu. Press the UP, DOWN, LEFT, and RIGHT arrow buttons to navigate the menu options and to change values.
FNUCTION (F1~F4) TBD PIP Preview and PIP Program When looking at the top right corner of the SE-2200 Control Panel / Keyboard there are four PIP keys. These are labelled Program and Preview. The upper PIP1 and PIP2 keys relate to activating Picture In Picture images on the Program outputs. The lower PIP1 and PIP2 keys relate to activating Picture In Picture images on the Multi-view or Preview outputs. For more detail, please see the Picture in Picture Function.
CUT This performs a simple immediate switch from the current main source to the selected sub source. The selected transition wipe or MIX is not used. AUTO TAKE This performs an automated switch from the current program source to the selected Preview source. The selected transition wipe or MIX will also be used. The timing of the transition is set by the chosen Speed button. MIX Pressing this button selects a basic A/B Dissolve for the next transition.
Menu Options When the ENTER button is pressed the Main Menu list is displayed on the HDMI 1 Multi-view output. This section covers the Menu options in the order that they appear on the SE-2200 HDMI 1 Multi-view. These settings may also appear in more detail elsewhere in this instruction manual. Options may vary depending on the firmware version in use. Once the chosen setting has been confirmed with the ENTER button it is stored within the switchers non-volatile memory.
6. Audio Settings Dynamic Range(dB) Audio Cross Point 18 or 24 Button 1~6 SDI De-EMB. Audio Setup Input 1~6 HDMI De-EMB. Audio Setup Audio (Re)-Embedding Setup Input 5,6 Output 1~6 X-Type, V-Type Audio Mixing Type 7. PIP Settings PIP1 PIP2 8. LOGO Settings Logo1 Logo2 9.
How to use the CG-200 software with SE-2200 For example: 1. Use HDMI cable connects the SE-2200 (CH-6.) and PC. 2. Into SE-2200 Main Menu to setting Video standard. 1. Mode 1080i 720p SD 4:3 SD 16:9 The Video can be changed to the desired standard. 3. Into SE-2200 Main Menu to setting Video input 6 on HDMI. SDI 3. Input 5 and 6 Mode HDMI Input 5 Input 6 HDMI Color Mode RGB YUU_422 YUV_444 4.
5. Install the CG-200 software to the PC. Step1: Please click the icon to install CG-200 Software Step2: Step by Step install the CG software to finish. Step3: When finished, please double click the icon to execute the software. 6. Enter the Settings into Preferences to select Video Mode (the video mode must the same as SE-2200).
7. Select DEMO file to play the CG data (the video standard must the same as SE-2200). 8. Set HDMI output to the “ON”. 9. Enter “Play all” to enable CG function.
SE-2200 Video Layers The SE-2200 is a Standard Definition or High Definition Digital Video Switcher and as well as mixing video and audio sources it has additional functions such as Picture in Picture (PIP), DSK LUMA KEY and LOGOs. Before attempting to use the SE-2200’s PIP, DSK LUMA KEY and LOGO functions it may help to first understand the order of the video layers at the SE-2200 Program (PGM) outputs. The Background video layer is the normal video layer when mixing and switching with the SE-2200.
Picture in Picture Function The SE-2200 Picture in Picture function allows you to place one or two smaller PIP images over a chosen full size background image. The smaller PIP images can be set to pre-defined sizes and positioned almost anywhere within the Preset/Program screen area. These PIP windows can also have a coloured border applied, and can be brought into the production with a default PIP dissolve transition.
DSK Function The SE-2200 has two Down Stream Keys (DSK PGM, DSK PVW). This means it is able to take a key source video input and replace the white or black parts of this image with the video from another source. If the input video carries an alpha channel it is also possible to key in this way too. DSK Settings Before trying to activate the DSK function it is best to understand how to set up or choose the right options for your production well in advance of the production.
AUDIO Function Overview The SE-2200 has a simple, cost effective, audio switcher built in. The SE-2200 has the ability to take audio from several sources either XLR analogue, SDI and/or HDMI inputs. The audio can be embedded onto the HDMI and SDI outputs and/or fed to the analogue XLR audio connections.
AUDIO FOLLOW VIDEO AUDIO FOLLOW VIDEO function is also known as audio follow video. This means that the audio source will switch with the corresponding video input, and actually follow the T-bar function. The active audio is de-embedded and sent to the audio output terminals for processing and/or audio levelling/ and or adding more audio sources. The resulting audio will return and be connected to the audio inputs for the purpose of (re)-embedding the audio to the SDI output.
Audio Menu Options – De-embedding SDI or HDMI audio Using the following SE-2200 menu options audio can be selected from the SDI or HDMI video inputs. SDI De-EMB. Audio Setup Inputs 1 to 6 User choice of Group 1,2,3 or 4 Pair 1 or 2 HDMI De-EMB. Audio Setup Input 5 or 6 User choice of Pair 1,2,3 or 4 As each SDI / HD-SDI source can have up to sixteen channels of audio, and HDMI eight channels, we need to choose the audio channels with the options above and by the following reference tables.
Working with a fixed or single audio source Example 1: We have two mono mics (channels 1 & 2) connected to a HD camera. These embedded audio channels are then output from this camera, HD-SDI, to the SE-2200 switcher. If we want to only hear these two audio channels regardless of the video channel used then we would set up the switcher in the following way. Press the ENTER key in the MENU area of the SE-2200 keyboard to display the on screen menu on the AUDIO ASSOCIATION of AUDIO SETTING.
How to Re-calibrate the SE-2200 T-Bar After a firmware update of the switcher it will be necessary to re-calibrate the T-Bar to get it working correctly. 1. Move the T-Bar to its lowest position. 2. Power OFF the SE-2200 switcher. 3. Press and hold down button 1 on both the Program and Preset rows of the switcher’s keyboard. 4. Power ON the SE-2200 switcher while still holding down the buttons in step 3. 5.
GPI Connections The SE-2200 can control external recorder/playback devices like the HDR-60/70 via simple contact closure GPI switch. The GPI interface is a 3.5mm Jack Socket which is situated on the rear panel of the SE-2200. Contact closure between the Outer and Inner contacts on the jack plug will trigger a user selected event. Power is supplied by the SE2200 and is less than 5V DC.
Example SE-2200 Set Up 28
Dimensions 29
Specification Connections Total Video Inputs Total Outputs Multi view Out SDI Video Input HDMI Video Input Analog Audio Output SDI Audio Output Analog Audio Input Internal Frame Synchronizers PGM Out Multi view Out AUX output Control Panel Connection Tally Out GPI Software Updates Total 6 video inputs ( 6 SDI or 4 SDI + 2 HDMI ) Total 6 SDI video outputs + 2 HDMI Multi view output HDMI Max 6 Max 2 2 mono ( 1 stereo) SDI Embedded Audio 4 mono (2 stereo) 6 Frame Synchronizers Up to 6 HDMI x 2 (HDMI multi-vie
Notes 31
