PD1 19” Rack Mount Power Center User’s Guide http:// www.datavideotek.
Warnings and Precautions 1. Read all of these warnings and save them for later reference. 2. Follow all warnings and instructions marked on this unit. 3. Unplug this unit from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 4. Do not use this unit in or near water. 5. Do not place this unit on an unstable cart, stand, or table. The unit may fall, causing serious damage. 6.
Warranty Datavideo warrants that the equipment it manufactures shall be free from defects in material and workmanship for a period of 12 months from the date of product purchased. If equipment fails due to such defects, Datavideo will, at its option, repair or provide a replacement for the defective part or product.
Introduction The PD1 is a 19” Rack Mount Power Centre. It is able to supply multiple 12V and 5V power outputs from an 110V/220V AC Input. The PD1 is an essential accessory for Datavideo Mobile Studio applications, together with the SE800 switcher, LCD, recorders…the PD1 makes the integration of a Mobile Studio become easier and more professional.
Front Panel: Select Input source Two bypass AC outputs Two cooling fans from DC or AC External DC12Volt/30A Input External AC input. *Note: AC 110 and 220 are different models Power Switch On / Off Switch Powers the PD1 On / Off when using AC Power. N.B. From DC Power the On / Off Switch is redundant AC In with builtin fuse AC Inlet for connecting to suitable mains power outlet – 100~120V or 220~240V according to model. The socket contains a fuse holder fitted with a 10A fuse. N.B.
AC Outlet 110V / 240V 5A 2 x AC Outlet at same voltage as AC Input (110~120 / 220~240V according to model) N.B. Sockets are redundant when PD1 is powered from DC DC In The PD1 can be powered from a suitable 12V power source. When working from DC the PD1 will not regulate the power outlets. Please ensure that the 12V power source that you use is regulated. If you intend to run the PD1 from a car or van power outlet make sure that a suitable regulator is used on the power feed.
Rear Panel: Bypass AC Output 2.1m DC 5V/1A Output XLR DC12V / 5A Output 2.1m DC 12V / 2A Output XLR DC12V + 2.1m DV12V 7A Output 2.1m DC 12V / 2A Output 2.1m DC12V Jack output x 2 for total 4A max rating 2.1m DC12V Jack output x 2 for total 4A max rating DC Out 5V 1A 5V 1A DC Output via 2.1mm InLine Socket (Centre Positive) DC Out 12V 2A 2 x 12V 2A DC Output via 2.1mm InLine Sockets (Centre Positive) DC Out 12V 4A 4 x 12V 4A DC Output via 2.
DC Out 12V 7A 2 x 12V 7A DC Outputs. 1 x 2.1mm InLine Sockets (Centre Positive), and 1 x 4 Pin XLR Socket (Pin 4 Positive, Pin 1 Ground) DC Out 12V 5A 1 x 12V 5A Output via 4 Pin XLR Socket (Pin 4 Positive, Pin 1 Ground) AC Outlet 1.5A 110V / 3A 240V AC Outlet at same voltage as AC Input (110~120 / 220~240V according to model) N.B.
Specification: INPUT ITEM Specification VOLTAGE (AC) 110V, 220V – Separate models RANGE 100~120V AC / 220~240V AC FREQ.
Service and Support It is our goal to make your products ownership a satisfying experience. Our supporting staff is available to assist you in setting up and operating your system. Please refer to our web site www.datavideotek.com for answers to common questions, support requests or contact your local office below. Datavideo Corporation (USA) 12300U East Washington Blvd., Whittier, CA 90606 USA Tel: +1 562 696 2324 contactus@datavideo.us www.datavideo.
