Table of contents Warranty ........................................................................................................................................................................... 3 Disposal............................................................................................................................................................................ 3 Packing List ...................................................................................................................
Warranty Standard Warranty • Datavideo equipment is guaranteed against any manufacturing defects for one year from the date of purchase. • The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty. • Damage caused by accident, misuse, unauthorized repairs, sand, grit or water is not covered by this warranty. • All mail or transportation costs including insurance are at the expense of the owner.
Unpacking the HRS-30 Place the HRS-30 on a level desk or surface. The carry handle will be at the right side facing the operator’s position. To open the HRS-30 monitor lid slide the thumb catches in the direction shown to their outer most position. Then lift the monitor lid upwards away from the keyboard and carry handle. HRS-30 Top View Monitor Speaker Monitor Operation keyboard Record Operation keyboard 2.
HRS-30 & Battery The HRS-30 can be powered from a standard V-Mount battery connection or mains power. This enables you to power the HRS-30 using an existing camera battery.
Rear Panel Black Burst / Loop Through Out Black Burst / Loop Through Out can be used as a video reference source when synchronization other devices to the HRS-30. Note: User needs to add a 75 ohm terminator if this is the latest device of the Black Burst signal chain. Time Code Signal IN /OUT & Loop through OUT HRS-30 can use an internal or external time code source. In RECORD state, the source time code will through to output. In PLAY state, the output time code source is from the HRS-30 playing file.
Monitor Operation Keyboard USB Port USB ports for LED Light power supply also can supply USB power charge. USB ports only support 5V / 500mA. Power Switch Switches the monitor power On / Off. Stereo Phone Jack Plug For stereo headphones. The headphone volume is controlled by the Audio Level Adjustments. When this phone jack connected earphone, the HRS-30 speaker function will disable. Audio Level Adjustments Allow you to adjust the headphones volume. Aspect Ratio Button Sets the LCD aspect ratio to 4.
Monitor Menu Options PICTURE Step 1. Press the button into the monitor system setting mode. Step 2. Press button into the PICTURE setting position. Step 3. Press button again into the BRIGHTNESS setting position. Step 4. Press / Step 5. Press button to save your setting and return to the PICTURE setting menu.
FUNC Step 1. Press the button two times move to the monitor FUNC setting mode. Step 2. Press button into the FUNC setting position. Step 3. Press button again to setting the CENTER MARK ON/OFF on the screen. Step 4. Press / Step 6. Press button to setting the SAFETY ZONE range (80, 90 or OFF). button moving to the SAFETY ZONE setting. Note: To select a different setting (4:3 SCREEN, CINEMA ZONE) use the buttons. Follow the same procedure to set the others status.
SETUP Step 1. Press the button three times move to the monitor SETUP setting mode. Step 2. Press button move to the SETUP setting position. Step 3. Press button again into to the OSD TIME setting position. Step 4. Press / Step 5. Press button to save your setting and return to the SETUP setting menu. Step 6. Press / Step 7. Press button into to the OSD BLENDING setting position. Step 8. Press / Step 9. Press button to save your setting and return to the SETUP setting menu.
ADVANCED Step 1. Press the button four times into the monitor ADVANCED setting mode. Step 2. Press button into the RESET setting position. Step 3. Press button again which will return all the settings of the monitor to the factory defaults. Step 4. Press button into the ADVANCED setting mode. Step 5. Press / Step 6. Press button, the version information will display on screen. Step 7. Press button exit the setting mode. button move to the VERSION setting position.
Recorder Operation Keyboard Menu Button This calls up the menu display which is navigated using the / Soft Keys. Enter or Skip 8 sec. Enter Key: Confirm your Recorder Operation select, display on 2’’ LCD panel. In order to activate Skip 8 sec. function while HRS-30 is playing a video clip, press Skip 8 sec. button and then press / Soft Keys to skip forward by 8~10 seconds or backward 8 ~ 10 seconds (depending on the recorded format).
Re-Playback Press this button once: Re-Playback from last 15 seconds of the last CLIP to review. Press this button two times: Re-Playback from last 15 seconds of the last CLIP to review. - IDLE Mode: Re-Playback from the last 15 seconds of the Last clip in the current BIN. - PLAY Mode: Skip back by 8~10 SEC. PREV / NEXT Soft Keys These two buttons are not only for skipping to Previous/Next clip but also for other functions, so these two buttons are also known as "Soft Keys.
Recorder Display Panel Status 08h19m 00 : 00: 12; 28 BIN 01 CLIP01 00:00:00 1X SYMBOL DESCRIPTION Type A: connect DC power indication Type B: connect battery power indication Loop Playback indicator 08h19m 00:00:12;28 Remaining Recording Space in Hours and Minutes Current Time Code or total length of CLIP Eight channel audio meters 1357 – Channels 1, 3, 5, 7 8642 – Channels 2, 4, 6, 8 Record, Pause, FWD, REV, Play, and Stop indication 1X 3X 6X 9X 12X Fast Forward or Fast Rewind speeds; Slow
Recorder Menu Key Options TOOL FIRMWARE REVISION Display the HRS-30 firmware information: CODEC, HOST, REC…etc. Step 1. Press the (MENU) button into the menu mode. [ MENU ] TOOL SETUP STATUS UP DOWN Step 2. Press the (ENTER) button into the TOOL menu. [ TOOL ] FIRMWARE VERSION ERASE THIS BIN FORMAT MEDIA UPGRADE FIRMWARE UN - LOCK MEDIA UP Step 3. Press the DOWN (ENTER) button again to see the FIRMWARE VRESION.
ERASE THIS BIN ERASE THIS BIN is used for deleting individual bins from the HRS-30. Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (ENTER) button into the TOOL menu. Step 3. Press the (UP) button / (DOWN) button select to the ERASE THIS BIN menu. [ TOOL ] FIRMWARE VERSION ERASE THIS BIN FORMAT MEDIA UPGRADE FIRMWARE UN - LOCK MEDIA UP DOWN Step 4. Press the (ENTER) button into the ERASE THIS BIN menu.
FORMAT MEDIA Format Media will remove all bins from the hard drive. Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (ENTER) button into the TOOL menu. Step 3. Press the (UP) button / (DOWN) button select to the FORMAT MEDIA menu. [ TOOL ] FIRMWARE VERSION ERASE THIS BIN FORMAT MEDIA UPGRADE FIRMWARE UN - LOCK MEDIA UP Step 4. Press the DOWN (ENTER) button into the FORMAT MEDIA menu. [ FORMAT MEDIA ] CONTENTS WILL LOST ! ARE YOU SURE FORMAT CANCEL UP DOWN Step 5.
UPRGRADE FIRMWARE HRS-30 has two parts firmware need to Update: Part 1: Recorder Keyboard Step 1. Use the USB (Type A to Mini USB) cable to the HRS-30 rear side mini USB port, and connect to your computer. Step 2. Power on the HRS-30, a new USB disk should appear on the computer Step 3. Copy firmware.bin and overwrite the firmware file in the destination file folder. Step 4. Safe remove the USB disk. Part 2: Recorder Main Board Step 1. Select the FORMAT MEDIA function to format 2.5’’ HDD. Step 2.
UN-LOCK MEDIA After you record file at HRS-30, the 2.5’’HDD format become read only. To set disk writable please do UN-LOCK MEDIA. Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (ENTER) button into the TOOL menu. Step 3. Press the (UP) button / (DOWN) button select to the UN-LOCK MEDIA menu. [ TOOL ] FIRMWARE VERSION ERASE THIS BIN FORMAT MEDIA UPGRADE FIRMWARE UN - LOCK MEDIA UP Step 4. Press the DOWN (ENTER) button to unlock media files. UNLOCKING MEDIA . . .
SETUP RECORD SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (UP) button / (DOWN) button select to the SETUP menu. [ MENU ] TOOL SETUP STATUS UP DOWN Step 3. Press the (ENTER) button into the SETUP menu. [ SETUP ] REC SETUP PLAY SETUP SYSTEM SETUP SAVE SETUP RECALL SETUP DOWN UP Step 4. Press the (ENTER) button into the REC SETUP menu.
Step 5. Press the (UP) button / (DOWN) button to select the HD ENCODE FORMAT / SD ENCODE FORMAT / REC FILE TYPE / REC CHANNEL NUM / SD ASPECT RATIO / TIME LAPSE / PWRON AUTO REC menu. Step 6. Press the (ENTER) button into the HD ENCODE FORMAT / SD ENCODE FORMAT / REC FILE TYPE / REC CHANNEL NUM / SD ASPECT RATIO / TIME LAPSE / PWR-ON AUTO REC menu. HD ENCODE FORMAT - Setting the HD video encode format to 100M I FRAME ONLY or 125M I FRAME ONLY (encode Intra frame only).
NUMBERS OF AUD CH - Audio channel selection: User can select to record 2, 4 or 8 audio channels. [ NUMBERS OF AUD CH ] 2CH 4CH 8CH UP DOWN SD ASPECT RATIO - Sets the SD aspect ratio to 16:9 or 4:3. [ SD ASPECT RAITIO ] 4:3 16 : 9 UP DOWN TIME LAPSE - Setting the TIME LAPSE ON/ OFF. Setting the TIME LAPSE FRAME RATE (1 frame / 1 sec). Setting the TIME LAPSE CYCLE (y frame per x sec).
PLAY SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button select to the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. [ SETUP ] REC SETUP PLAY SETUP SYSTEM SETUP SAVE SETUP RECALL SETUP UP DOWN Step 4. Press the (UP) button / (DOWN) button to select the PLAY SETUP menu. Step 5. Press the (ENTER) button into the PLAY SETUP menu. [ PLAY SETUP ] LOOP PLAY POW ON AUTO PLAY GEN LOCK PLAY CENTRIC UP DOWN Step 6.
LOOP PLAY - Setting the LOOP PLAY mode (on / off). [ LOOP PLAY ] ON OFF UP DOWN POWER ON AUTO PLAY - Setting the POWER ON AUTO PLAY mode (on / off). [ POWER ON AUTO PLAY ] ON OFF UP DOWN GEN LOCK - Setting the GEN LOCK mode (on / off). [ GEN LOCK ] ON OFF UP DOWN Note: Genlock is only available in play mode. PLAY CENTRIC - Setting the PLAY CENTRIC mode (bin / CLIP). [ PLAY CENTRIC ] BIN CLIP UP DOWN CLIP = When LOOP PLAY mode is on, HRS-30 will loop play CLIP file.
SYSTEM SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button select to the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. Step 4. Press the (UP) button / (DOWN) button select to the SYSTEM SETUP menu. [ SETUP ] REC SETUP PLAY SETUP SYSTEM SETUP SAVE SETUP RECALL SETUP UP Step 5. Press the DOWN (ENTER) button into the SYSTEM SETUP menu. [ SYSTEM SETUP ] TIME CODE REMOTE CONTROL BUZZER LONG TIME STOP DATE & TIME SETUP Step 6.
TIMECODE Setting the TIME CODE running at INTERNAL RCA RUN / INTERNAL FREE RUN / EXTERNAL TC IN or EXTERNAL SDI TC. [ TIME CODE ] INTERNAL REC RUN INTERNAL FREE RUN EXTERNAL TC IN EXTERNAL SDI TC UP DOWN Note: INTERNAL FREE RUN time code follows system real time clock. REMOTE CONTROL Setting the REMOTE CONTROL (rear panel RJ-45 connector) function on / off. [ REMOTE CONTROL ] DISABLE ENABLE UP DOWN Note: When this function enable, other button function will disable.
LONG TIME STOP Setting the HOLD 1 SECONDS TO STOP function on / off. [ LONG TIME STOP ] ON OFF UP DOWN DATE & TIME SETUP Into the DATE & TIME SETUP mode, use the (UP) / (Rew) buttons to setting the DATE & TIME.
SAVE SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button into the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. Step 4. Press the (UP) button / (DOWN) button select to the SAVE SETUP menu. [ SETUP ] REC SETUP PLAY SETUP SYSTEM SETUP SAVE SETUP RECALL SETUP UP Step 5. Press the DOWN (ENTER) button into the SAVE ETUP menu. [ SAVE SETUP ] USER # 1 USER # 2 UP DOWN Step 6. Press the (UP) button / Step 7.
RECALL SETUP Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (DOWN) button into the SETUP menu. Step 3. Press the (ENTER) button into the SETUP menu. Step 4. Press the (UP) button / (DOWN) button select to the RECALL SETUP menu. [ SETUP ] REC SETUP PLAY SETUP SYSTEM SETUP SAVE SETUP RECALL SETUP UP Step 5. Press the DOWN (ENTER) button into the RECALL SETUP menu. Step 6. Press the (UP) button / FACTORY DEFAULT file.
STATUS Step 1. Press the (MENU) button into the menu mode. Step 2. Press the (UP) button / (DOWN) button select to the STATUS menu. [ MENU ] TOOL SETUP STATUS UP DOWN Step 3. Press the (ENTER) button into the STATUS menu. Step 4. Press the (UP) button / (DOWN) button to see the FILE FORMAT / BIN FILE LENGTH / RECORD SETUP / INPUT / TIME CODE / GENLOCK status. [ FILE FORMAT ] [ RECORD SETUP ] 1080 59.94I . MXF 50M 4 : 2 : 2 LONG - GOP 4 CHANNEL AUDIO [ HD ] .
Assemble 2.5" HDD in Removable Rack Step 1. Put the 2.5" HDD into the rack. Step 2. Assemble four screws to fasten 2.5" HDD on the rack. Step 3. Push the button to Left side and then push the rack into HRS-30. Step 4. Push the button to right side, for lock the rack.
Connecting the 2.5’’HDD to PC The HDD drive caddy can be pull out and connected to a PC or MAC with the supplied USB cable. Step 1. First turn off the HRS-30. Step 2. Turn the drive caddy lock lever to the right to unlock the HDD drive caddy. Pull out the HDD drive caddy. Step 3. The HDD drive caddy is fitted with a SATA connector on its rear; this can provide power to the HDD, as well as allow the exchange of data. Step 4.
Connecting the 2.5’’HDD to MAC Step 1. Connect the supplied SATA-USB cable to the HDD drive caddy, and connect the double lead to your MAC. Please connect two USB to your MAC. Step 2. A Datavideo drive will appear on the desktop. Step 3. If you access the drive you will see the files are available for copying across to a local drive, or direct access.
Q&A Q 1: What causes the HRS-30 to show “CLOSE TO FULL” on the 2’’ LCD Display Panel? Ans: When HRS-30 HDD recordable time is less than 5 minutes, the HRS-30 will show “CLOSE TO FULL” on Recorder Monitor. Q 2: While the HRS-30 is recording, what sudden power loss cause? Ans: HRS-30 will lose the last 6 seconds of recorded data on the HDD.
HRS-30 Error Codes XX 01: Interface FPGA no response when boot 02: Recorder FW no response when boot 03: Codec FW no response when boot 04: Main board and Controller connect error.
HRS-30 RS-232 Control Command 1. Interface Overview Standard transmission rate on the interface bus is 38400 bits per seconds (bps) 1 Start bit + 8 Data bits + 1 Parity bit + 1 Stop bit. Odd Parity 2.
Command Name Response Data Vender Unique System Commands (External) Make Media File (Unlock Media) Empty Current Bin Empty All (Format Media) Sense Control Time code Sense Status Sense Variable Status Sense Vender Unique Sense Control 01h, F6h, 00, F7h 01h, F6h, 01, F8h 01h, F6h, 02, F9h 61h, 0Ch, 04h, 71h 61h, 20h, 0Fh, 90h 61h, 20h, xnh, csum 62h, F2h, 05h, 00h, 59h Firmware Revision Sense (Recorder) 62h, F2h, 05h, 01h, 5Ah Firmware Revision Sense (Host) 62h, F2h, 05h, 02h, 5Bh Firmware Revision
4. Trick Play 21h 13h nn csum : Shuttle Forward 21h 23h nn csum : Shuttle Reverse nn speed Command Forward 62h 12X 21h 13h 62h 96h 5E h 9X 21h 13h 5Eh 92h 58 h 6X 21h 13h 58h 8Ch 4F h 3X 21h 13h 4Fh 83h 40h 1X 21h 13h 40h 74h 36h 1/2X 30 h 1/3X 27h 1/6X 21h 1/9X 1Dh 1/12X Note: 1/2X is for I-frame only.
7. Variable Status Sense 61h, 20 h, xnh, csum The return-byte is variable for Status Sense. The 3rd byte of command: MSD (Bit7~4, x): Indicates the initial byte index of the to be returned. LSD (Bit3~0, n): Indicates the number of data bytes to be returned. 8.
Example HRS-30 Set Up Type A: 40
Type B: 41
RJ-45 Pin Define This pin define is use for RJ-45 connect to RS-232 connector. Dimensions All measurements in millimetres (mm).
Specifications General Specification Video Standard HD/SD Video Format 1080P 23.97/24Hz 1080i 50/59.94/60Hz 720P 50/59.94/60Hz 480i / 576i Storage Medium 2.5" HDD / SSD, Max capacity 1T GB ＊Note: SSD is recommended Estimated Record Time (min per 10GB) SD:22(50Mbps) ~75(8Mbps) HD: 10 (125Mbps)~68 (10Mbps) How to retrieve Recorded Content Removable HDD/SSD, transfer data via USB 3.0 Recorded File Format MXF OP1A, MOV MPEG2 Long GOP HD: 1. 10Mbps 4:2:0 1440x1080/1280x720, 2.
Panel Specification Screen size 10.1” Resolution 1280（H）× 800（V） Dot pitch 0.0565（W）× 0.1695（H）mm Active Area 216.96（W）× 135.60（H）mm Interface Support Video Input Signal 1 x SDI Monitoring/ Playback output 1 x SDI(input loop thru) 1 x HDMI ; 1 x SDI (Out) Analog Audio Input N/A Audio Output 1 x 3.5mm jack for external speaker Speakers 2 x 3W Earphone：3.
Notes 45
Notes 46
Notes 47
Service & Support 48
