User Manual
Table Of Contents
- MOSAIC™ regulations and Warranty information
- FCC Regulations
- Introduction
- Equipment
- Installation Considerations
- Installation Supplies
- FIREFLY Menu Screen
- Programming MOSAIC FIREFLYs
- Connecting the Remote Shutoff Valve
- Extract Profile Data
- Program GPS Coordinates
- Options
- Operate RSV
- Set Phy Fram
- Set FF To Ship Mode
- Upgrade Firmware
- Set FF Date/Time
- View Mesh Neighbors
- Set Radio Port
- Joining the MESH Network/LED Status
- General LED Information
- MOSAIC FIREFLYs Connected to an Encoded Meter (Mesh Mode)
- MOSAIC FIREFLYs Connected to a Pulse Meter (Mesh Mode)
- MOSAIC Sensor-end FIREFLYs (Mesh Mode)
- MOSAIC FIREFLYs as Repeaters (Mesh Mode)
- MOSAIC FIREFLYs in Non-Mesh Mode
- MOSIAC FIREFLYs on Encoded Meters (Non-Mesh Mode)
- MOSAIC FIREFLYs on Pulse Meters (Non-Mesh Mode)
- MOSAIC FIREFLYs (D411X only) Connected to Remote Shutoff Valves
- Troubleshooting Procedures
- Mounting the MOSAIC FIREFLY
- FAQ’s
- Can I use both MOSAIC Gateway backhaul types in a single installation?
- Why would I need to use GPRS in an installation?
- How many MOSAIC FIREFLYs can mesh together?
- What is the output power of a MOSAIC FIREFLY?
- What is the range of a MOSAIC FIREFLY?
- Are the new MOSAIC FIREFLYs compatible with previous legacy FIREFLYs?
- Do the MOSAIC FIREFLYs read via the ROADRUNNER MOBILE product?
- Will I need different MOSAIC FIREFLYS for Mesh and Mobile functionality?
- How do I program an MOSAIC FIREFLY?
- What does your handheld programming tool look like?
- What is the battery life for the MOSAIC FIREFLY?
- Is the battery pack replaceable?
- What frequency does the MOSAIC product use?
- Do you use a licensed frequency?
- Does your product provide profiling?
- How do you get the profiling?
- How often do I get reads via the Mesh?
- Is the system 2-way?
- What can I do with the 2-way functionality?
- Does the MOSAIC system have repeaters?
- How do the MOSAIC FIREFLY repeaters work?
- What is the MOSAIC FIREFLY repeater battery life?
- Do you support cellular backhaul from the MOSAIC Gateway?
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- Support
- Consumables
- Return Material Authorizations (RMAs)
- Training and Support
Datamatic, LTD. System Training Manual Version 08.24.12
- 67 -
Confidential Datamatic, Ltd. 2012
2. If the MOSAIC FIREFLY is unable to join the network:
a. Verify that the MOSAIC FIREFLY is installed and mounted properly in the meter pit
b. Swipe the meter & refer to the LED Operational States for verification of functional
status Mesh (light will slow blink green). Go to the nearest neighboring MOSAIC
FIREFLY and swipe.
c. Check the unread MOSAIC FIREFLY for solid green light (this process can take several
attempts). Before swiping both units must be “asleep” (no LED lights) before attempting
to swipe again.
3. Continue monitoring in MOSAIC Software & replace unread MOSAIC FIREFLY if the issue
persists.
4. If after all troubleshooting is complete & you are unable to achieve a solid green light the
MOSAIC FIREFLY should be replaced.
a. If there is no LED response within 5 seconds of magnet swipe retry several times. If the
unit in question continues to be unresponsive it should be replaced.
Red Light is Not Solid After Installation
The MOSAIC FIREFLY has been wired but the red light never changes to solid upon installation.
1. Check the wire connections, it is likely there is a wiring problem.
2. Verify that the register head is working.
NOTE: When connected to a pulse meter, the red light will fast-blink until 5 pulses are received.