User Manual
Table Of Contents
- MOSAIC™ regulations and Warranty information
- FCC Regulations
- Introduction
- Equipment
- Installation Considerations
- Installation Supplies
- FIREFLY Menu Screen
- Programming MOSAIC FIREFLYs
- Connecting the Remote Shutoff Valve
- Extract Profile Data
- Program GPS Coordinates
- Options
- Operate RSV
- Set Phy Fram
- Set FF To Ship Mode
- Upgrade Firmware
- Set FF Date/Time
- View Mesh Neighbors
- Set Radio Port
- Joining the MESH Network/LED Status
- General LED Information
- MOSAIC FIREFLYs Connected to an Encoded Meter (Mesh Mode)
- MOSAIC FIREFLYs Connected to a Pulse Meter (Mesh Mode)
- MOSAIC Sensor-end FIREFLYs (Mesh Mode)
- MOSAIC FIREFLYs as Repeaters (Mesh Mode)
- MOSAIC FIREFLYs in Non-Mesh Mode
- MOSIAC FIREFLYs on Encoded Meters (Non-Mesh Mode)
- MOSAIC FIREFLYs on Pulse Meters (Non-Mesh Mode)
- MOSAIC FIREFLYs (D411X only) Connected to Remote Shutoff Valves
- Troubleshooting Procedures
- Mounting the MOSAIC FIREFLY
- FAQ’s
- Can I use both MOSAIC Gateway backhaul types in a single installation?
- Why would I need to use GPRS in an installation?
- How many MOSAIC FIREFLYs can mesh together?
- What is the output power of a MOSAIC FIREFLY?
- What is the range of a MOSAIC FIREFLY?
- Are the new MOSAIC FIREFLYs compatible with previous legacy FIREFLYs?
- Do the MOSAIC FIREFLYs read via the ROADRUNNER MOBILE product?
- Will I need different MOSAIC FIREFLYS for Mesh and Mobile functionality?
- How do I program an MOSAIC FIREFLY?
- What does your handheld programming tool look like?
- What is the battery life for the MOSAIC FIREFLY?
- Is the battery pack replaceable?
- What frequency does the MOSAIC product use?
- Do you use a licensed frequency?
- Does your product provide profiling?
- How do you get the profiling?
- How often do I get reads via the Mesh?
- Is the system 2-way?
- What can I do with the 2-way functionality?
- Does the MOSAIC system have repeaters?
- How do the MOSAIC FIREFLY repeaters work?
- What is the MOSAIC FIREFLY repeater battery life?
- Do you support cellular backhaul from the MOSAIC Gateway?
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- Support
- Consumables
- Return Material Authorizations (RMAs)
- Training and Support
Datamatic, LTD. System Training Manual Version 08.24.12
- 64 -
Confidential Datamatic, Ltd. 2012
MOSAIC FIREFLYs Connected to an Encoded Meter (Mesh Mode)
After a successful initial swipe, the GREEN LED will flash slowly as the MOSAIC FIREFLY searches
for the mesh. When communication has been established with a node already connected to the mesh
(MOSAIC Gateway, Repeater or another MOSAIC FIREFLY) the GREEN LED will go solid.
Additionally, the RED LED will flash slowly until it detects the encoder. If the MOSAIC FIREFLY
successfully connects to the encoder, the RED LED will go solid.
If the RED LED flashes quickly, the MOSAIC FIREFLY has detected its connection to a meter, but has
not received an acknowledgement that verifies it is connected to a supported encoder. In this scenario,
the wires may not be connected correctly or the encoder may not be supported in the current MOSAIC
FIREFLY firmware.
If the RED LED flashes slowly, the MOSAIC FIREFLY is searching for an acknowledgement from a
meter, but has not received any. The MOSAIC FIREFLY will continue to wait for an
acknowledgement, but will eventually go into ship mode if none is received.
The MOSAIC FIREFLY is successfully connected to an encoded meter and the mesh when both the
GREEN and RED LEDs are solid.
MOSAIC FIREFLYs Connected to a Pulse Meter (Mesh Mode)
After a successful initial swipe, the RED LED will blink slowly until it detects a connection with a pulse
meter. NOTE: this happens very quickly.
Once the MOSAIC FIREFLY detects the connection to a pulse meter, the RED LED blinks quickly until
5 meter pulses are detected. Once 5 pulses are detected, the RED LED will go solid.
If the MOSAIC FRIEFLY is not wired correctly, the RED LED will continue blink slowly, or the
MOSAIC FIREFLY could go back into ship mode (meaning the RED LED will go off after the magnet
swipe).
MOSAIC Sensor-end FIREFLYs (Mesh Mode)
After a successful magnet swipe, the RED LED will blink slowly as the FIREFLY attempts to achieve
the Target Background. Once the RED LED begins a fast blink then goes solid, the FIREFLY has
achieved the target background.
Additionally, the GREEN LED will flash slowly as the MOSAIC FIREFLY searches for the mesh.
When communication has been established with a node already connected to the mesh (MOSAIC
Gateway, Repeater or another MOSAIC FIREFLY) the GREEN LED will go solid.
If both the RED LED and the GREEN LED blink slowly, then go off. The FIREFLY was unable to
achieve the target background. Reprogramming should be attempted.