User Manual
Table Of Contents
- MOSAIC™ regulations and Warranty information
- FCC Regulations
- Introduction
- Equipment
- Installation Considerations
- Installation Supplies
- FIREFLY Menu Screen
- Programming MOSAIC FIREFLYs
- Connecting the Remote Shutoff Valve
- Extract Profile Data
- Program GPS Coordinates
- Options
- Operate RSV
- Set Phy Fram
- Set FF To Ship Mode
- Upgrade Firmware
- Set FF Date/Time
- View Mesh Neighbors
- Set Radio Port
- Joining the MESH Network/LED Status
- General LED Information
- MOSAIC FIREFLYs Connected to an Encoded Meter (Mesh Mode)
- MOSAIC FIREFLYs Connected to a Pulse Meter (Mesh Mode)
- MOSAIC Sensor-end FIREFLYs (Mesh Mode)
- MOSAIC FIREFLYs as Repeaters (Mesh Mode)
- MOSAIC FIREFLYs in Non-Mesh Mode
- MOSIAC FIREFLYs on Encoded Meters (Non-Mesh Mode)
- MOSAIC FIREFLYs on Pulse Meters (Non-Mesh Mode)
- MOSAIC FIREFLYs (D411X only) Connected to Remote Shutoff Valves
- Troubleshooting Procedures
- Mounting the MOSAIC FIREFLY
- FAQ’s
- Can I use both MOSAIC Gateway backhaul types in a single installation?
- Why would I need to use GPRS in an installation?
- How many MOSAIC FIREFLYs can mesh together?
- What is the output power of a MOSAIC FIREFLY?
- What is the range of a MOSAIC FIREFLY?
- Are the new MOSAIC FIREFLYs compatible with previous legacy FIREFLYs?
- Do the MOSAIC FIREFLYs read via the ROADRUNNER MOBILE product?
- Will I need different MOSAIC FIREFLYS for Mesh and Mobile functionality?
- How do I program an MOSAIC FIREFLY?
- What does your handheld programming tool look like?
- What is the battery life for the MOSAIC FIREFLY?
- Is the battery pack replaceable?
- What frequency does the MOSAIC product use?
- Do you use a licensed frequency?
- Does your product provide profiling?
- How do you get the profiling?
- How often do I get reads via the Mesh?
- Is the system 2-way?
- What can I do with the 2-way functionality?
- Does the MOSAIC system have repeaters?
- How do the MOSAIC FIREFLY repeaters work?
- What is the MOSAIC FIREFLY repeater battery life?
- Do you support cellular backhaul from the MOSAIC Gateway?
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- FIREFLY Template for_________________________________
- Support
- Consumables
- Return Material Authorizations (RMAs)
- Training and Support
Datamatic, LTD. System Training Manual Version 08.24.12
- 21 -
Confidential Datamatic, Ltd. 2012
FIREFLY Menu Screen
Select the FF Menu key on the ROADRUNNER CX to access these options:
1. Define Templates
(Setting this up saves time during the programming process. Please see Appendix
A – F for details.)
2. Program by Template
(Use to program the FIREFLY. Please see Programming the Sensor-end
MOSAIC FIREFLY and Programming Wire-end MOSAIC FIREFLY sections
below.)
3. Program by Parameter
(Use to reprogram a FIREFLY’s individual parameters settings.)
4. View Settings
(Allows the user to view all current parameters of that FIREFLY.)
5. Extract Profile Data
(Extracts reading, saves consumption. This is the FIREFLY’s history. Please see
the Extract Profile Data section below.)
6. Set Reading Mode
(Determines the way you will read the FIREFLYs. Please see the Pre-
Installation Setup section below.)
7. Program GPS Coords
(Use to program GPS coordinates to a FIREFLY or Gateway. Please see the
Program GPS Coordinates section below.)
8. Capture Config
(To manually capture configuration ‘programming’ data at any time.)
9. Options
(Use to set options for the ROADRUNNER. Please see the Options section
below for details.)
A. Operate RSV
(Use to operate a Remote Shutoff Valve connected to a FIREFLY. Please see the
Operate RSV section below for details.)
B. Set Phy Fram
(Sets the phy fram value)
C. Define AutoCAL Rules
(Use to set rules the FIREFLY must meet during AutoCAL. Please see the Pre-
Installation Setup section below.)
D. Set FF To Ship Mode
(Sets the FIREFLY to Ship mode. Please see the Set FF To Ship Mode section
below for details.)