BC-80X0 Cradle Quick Reference Guide
Datalogic ADC, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 ©2007-2014 Datalogic, Inc. An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”).
BC-80X0 USING THE BC-80X0 RADIO CRADLE The BC-80X0 cradle, paired with one or more Powerscan™ M8300 readers, builds a Cordless Reading System for the collection, decoding and transmission of barcoded data. It can be connected to a Host PC through an RS-232, USB, Wedge or Pen cable and is suited for single-cradle point-to-point layouts. It can also be connected to a C-BOX and therefore integrated into a fixed scanner application. The BC-8060 models also allow multi-cradle layouts through an RS-485 Network.
DATALOGIC To set up your BC-80X0 cradle you must: 1. Physically install the cradle. 2. Make all system connections. 3. Configure the BC-80X0 cradle. INSTALLATION MOUNTING THE BC-80X0 CRADLE The cradle package contains the following items: BC-80X0 1 horizontal base BC-80X0 Quick Reference Guide 2 wall-mounting lock hinges BC-8000 Antenna 4 rubber feet 2 adhesive strips 1 inclined base The cradle can be mounted for portable or fixed desktop usage, or it can be fixed to a wall.
BC-80X0 Desktop mounting For desktop usage, you can mount the cradle either on the horizontal base, for reduced overall dimensions, or on the inclined base for a more ergonomic taking out and insertion of the reader onto the cradle.
DATALOGIC PORTABLE DESKTOP USE 1. Correctly position the BC-80X0 onto the base by sliding it along the mounting tabs until aligned. 1 1 2 2 2. Carefully clean the rubber foot seats of the base to remove any impurities that could reduce adhesion. 3. Remove the protective plastic from the rubber feet and stick them onto the bottom surface of the base. 4. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight.
BC-80X0 5. Remove the plastic from the other side of the strips and affix the base to the table. 6. If mounting the BC-80X0 cradle, insert the antenna in the appropriate hole on the body of the cradle and screw it clockwise until tight. For mounting with screws: 1. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels, as shown in the figures below: 2. Position the base on the table and affix it by means of the screws (not provided). 3.
DATALOGIC 2. Position the cables to be connected to the BC-80X0 cradle along the dedicated channels (see figures at page 4). If using the adhesive strips: If using the mounting screws: 3. Carefully clean the adhesive strip seats of the base to remove any impurities that could reduce adhesion. 3. Using the mounting holes on the base as a pattern, mark the wall where you desire to mount the BC-80X0. 4.
BC-80X0 APPLYING RAPID LABEL (OPTIONAL) POINT-TO-POINT CONFIGURATION A pre-printed barcode label is included in the package for rapid configuration of point-topoint applications. If you wish to use this method, apply this label to the seat provided on the BC-80X0 cradle as shown in the figure. See the Powerscan™ M8300 Quick Reference Manual for the configuration procedure.
DATALOGIC CONNECTING AND INTERFACE CABLE DISCONNECTING THE BC-80X0 The BC-80X0 can be connected to a Host by means of an RS-232, USB, Wedge or Pen cable, which must be simply plugged into the Host connector, visible on the front panel of the cradle. To disconnect the cable, insert a paper clip or other similar object into the hole corresponding to the Host connector on the body of the cradle. Push down on the clip while unplugging the cable.
BC-80X0 WEDGE PEN C-BOX Powerscan™ M JOIN Scanner C-BOX BIND BC-80X0 System cables to Host 9
DATALOGIC BC-80X0 CONFIGURATION The BC-80X0 configuration can be performed in three ways: by using the Datalogic Aladdin™ software configuration program, by sending configuration strings from the Host PC via the RS-232 or USB-COM interface or by reading configuration barcodes with the Powerscan™ M reader. DATALOGIC ALADDIN™ Datalogic Aladdin™ is a multi-platform utility program providing a quick and user-friendly configuration method via the RS-232/USB-COM interface.
BC-80X0 INTERFACE SELECTION Select one of the interface codes according to your application. USB INTERFACE SELECTION USB-KBD Ì$+UA03$-:Î USB-KBD – ALT-mode Ì$+UA04$-@Î USB-COM* Ì$+UA02$-4Î USB-IBM-Hand Held Ì$+UA01$-.Î USB-IBM Table top Ì$+UA00$-(Î USB KBD-APPLE * When configuring USB-COM, the relevant files and drivers must be installed from the USB Device Installation Software, which can be downloaded from the web site http://www.scanning.datalogic.com.
DATALOGIC INTERFACE SELECTION Select one of the interface codes according to your application.
BC-80X0 KEYBOARD NATIONALITY USB-KBD and Wedge users should select one of the following wedge keyboard nationality codes according to your keyboard. Belge Ì$+FJ7$-8Î Deutsch Ì$+FJ3$-$Î English Ì$+FJ4$-)Î Español Ì$+FJ6$-3Î Français Ì$+FJ2$-ÊÎ Italiano Ì$+FJ1$-ÅÎ Svenskt Ì$+FJ5$-.
DATALOGIC The following Keyboard Nationality selections are only valid for IBM AT compatible PCs: Japanese Ì$+FJ8$-=Î Russian (Latin) Ì$+FJ9$-BÎ Russian (Cyrillic) Ì$+FJA$-jÎ Hungarian Ì$+FJB$-oÎ Slovenian, Croatian, Serbian (Latin) Ì$+FJC$-tÎ Romanian Ì$+FJD$-yÎ Czech Republic Ì$+FJE$-~Î 14
BC-80X0 DATA FORMAT TERMINATORS For your convenience, some common Terminators are given below. For other Header/Terminators selections, Data Format and Advanced Data Format parameters see the Powerscan™ D8330/M8300 Reference Manual.
DATALOGIC BC-80X0 DEFAULT CONFIGURATION USB-KBD DEFAULT SETTINGS USA keyboard, FIFO enabled, inter-character and inter-code delays disabled, USB keyboard speed normal. DATA FORMAT: code identifier disabled, code length not transmitted, character replacement disabled, reader and cradle address stamping disabled, reader and cradle address delimiter disabled, time stamping disabled, time stamping delimiter disabled, no header, terminator = ENTER.
BC-80X0 OPERATING TEST Read the TEST codes below. EAN-8 1234 5670 EAN-13 1 234567 000992 Code 39 (Normal) Code 39 (Normal) 1 7 1 6 2 Code 128 t e s t Interleaved 2 of 5 0123456784 YOUR SYSTEM IS NOW READY TO READ CODES AND TO SEND THE DATA TO THE HOST.
DATALOGIC TECHNICAL FEATURES BC-80X0 Electrical Features Supply Voltage External Power Host Power Power Consumption External Power Host Power Indicators Time of Recharge External Power Host Power 10..30 VDC 5 VDC ±10% max. 10 W (charging) * max. 500 mA (charging) Ext. Power/Data yellow LED Host Power/Data yellow LED Reader batt. state green/red LED Spare batt. state green/red LED (BC-8060 only) beeper max. 4 hours with 2150 mAh Li-Ion battery max.
BC-80X0 WARRANTY DATALOGIC ADC LIMITED FACTORY WARRANTY Warranty Coverage Datalogic warranties this product against defects in workmanship and materials, for a period of 3 years from the date of shipment, provided that the product is operated under normal and proper conditions. Datalogic ADC (“Datalogic”) hardware products are warranted against defects in material and workmanship under normal and proper use.
DATALOGIC shipping charges, duties, taxes, and any other charges for products returned to any other locations. Failure to follow the applicable RMA policy, may result in a processing fee. Customer shall be responsible for return shipment expenses for products which Datalogic, at its sole discretion, determines are not defective or eligible for warranty repair.
BC-80X0 CUSTOMER OR ANY THIRD PARTY FOR ANY LOST PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL IN-DIRECT, SPECIAL OR CONTINGENT DAMAGES REGARDLESS OF WHETHER DATALOGIC HAD ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES. Risk of Loss Customer shall bear risk of loss or damage for product in transit to Datalogic. Datalogic shall assume risk of loss or damage for product in Datalogic’s possession.
DATALOGIC COMPLIANCE This device must be opened by qualified personnel only. POWER SUPPLY This device is intended to be supplied by a UL Listed/CSA Certified Power Unit marked "Class 2" or LPS power source rated 10-30 V DC, minimum 1 A, which supplies power directly to the cradle. FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules.
BC-80X0 COFETEL MEXICO STATEMENTS Cofetel Mexico Update Este producto es usable en México Certificado Nr. RCPDAST08-0269 (COFETEL). Cofetel Mexico Update Este producto es usable en México Certificado Nr. RCPDAST09-0861 (COFETEL). BRAZILIAN CERTIFICATION STATEMENT (01)07898916345048 “Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.
DATALOGIC 24
BC-80X0 WEEE COMPLIANCE Waste Electrical Statement and Electronic Equipment (WEEE) English For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.datalogic.com. Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.datalogic.com. French Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet www.datalogic.com.
DATALOGIC NOTES 26
BC-80X0 NOTES 27
DATALOGIC NOTES 28
DECLARATION OF CONFORMITY 13 Datalogic ADC Srl, Via S. Vitalino, 13 Lippo di Calderara di Reno (BO) 40012 Italy EC-051 Rev.: 3 Pag.
www.datalogic.com ©2007-2014 Datalogic, Inc. • All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic ADC, Inc.
