Quick Start Guide

Remove the Memor 20 from the
3-Slot Dock Full
The Memor 20 3-Slot Dock Full can be unlocked using the unlock key
provided with the cradle or by software sending an unlock command
from the inserted device (see the Memor 20 user’s manual or the SDK
documentation).
To locally unlock the dock, insert the unlock key into the opening and gently
press it all the way down:
You can now remove the Memor 20.
Power the Dock
Use only the Datalogic power supply 94ACC0250 to power the
3-Slot Dock Full.
CAUTION
Plug the power supply cable into the power connector on the back of the
dock, then plug the power supply into the AC/DC plug.
Daisy Chain Connection
The daisy chain connection allows to power two docks with one power
supply.
To connect a second cradle use the JoyaTouch/M1/Memor20 Power
Jumper (available as optional accessory, p/n 91ACC0049).
1. Connect the first dock to the second dock using the power jumper.
2. Connect the power supply to the first dock.
3. Plug the power supply into the AC/DC plug.
Charge the Memor 20
Insert the device into the dock with the screen facing front and the head
facing up.
The dock is able to provide wireless power to the Memor 20 when the
device is correctly inserted.
Use the Dock Manager application on your Memor 20 to select the
charging mode (standard or fast). See the Memor 20 User Manual for more
information.
.
Make sure there is nothing between the dock and the device.
Do not put any foreign object such as, but not limited to, coins,
paper clips, stickers inside the slot of any of the docks.
CAUTION
Do not attempt to charge any other device different from the
Memor 20 devices.
WARNING
Under the same conditions, the fast charge connection can
charge the battery up to twice as fast as the standard charge
connection.
NOTE
Ethernet Connection
1. Connect the 3-Slot Dock Full to the power supply (available as optional
accessory, p/n 94ACC0250).
2. Plug a CAT-5 ethernet cable into the ethernet port on the back of the
dock.
3. Plug the ethernet cable into the ethernet hub or a port on the host
device.
4. Remove the cap from the pogo pins on the dock.
5. Remove the USB rubber cap from the Memor 20.
6. Insert the USB/ethernet plug included in the dock’s box and fasten it
with the two provided screws.
7. Turn on the Memor 20.
8. Insert the Memor 20 into the dock.
Ethernet Hub
CAT-5
Ethernet Cable
3-Slot Dock
Full
Power Supply
(P/N 94ACC0250)
Memor 20
LED Indicators
LED Behavior Operation Status
Power ON
Solid green Dock is powered
Foreign Object Detection (FOD)
Blinks red at 4 Hz Foreign object detected, output
power is disabled.
Notification
Blinks green once Device insertion
Solid green (until device extraction or
timeout expiration)
Device extraction
Blink red, 1 quick pulse Failure - Lever error
Blink red, 2 quick pulses Failure - WLC FOD
Blink red, 3 quick pulses Failure - WLC error
Blink red, 4 quick pulses Failure - Daisy-chain error
In case of FOD led blinking, remove the foreign object.
CAUTION
You can change the Notification LED behavior using the Datalogic
SDK.
NOTE
Technical Specifications
Electrical Features
Indicators Consumption Power on LED (green)
FOD LED (red)
Notification LEDs (green/red)
Environmental Features
Working Temperature 0°C to 45°C
Storage Temperature -30°C to 70°C
Humidity 5-95% non condensing
Mechanical Features
Dimensions 368.3 x 120 x 112 mm / 14.5 x 4.7 x 4.4 in
Weight 1390 g / 49 oz