Specifications

ManualsBrandsDatalogic ManualsBarcode ReaderPOWERSCAN PBT7100 guide

PowerScan

PBT7100 Cordless

Linear Imaging Barcode Reader

Product Reference Guide

Summary of content (352 pages)

PAGE 1
PowerScan® PBT7100 Cordless Linear Imaging Barcode Reader Product Reference Guide
PAGE 2
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
PAGE 3
Table of Contents Chapter 1. Introduction ................................................................................................................................................................. 1 About this Guide ...............................................................................................................................................................................................................1 Manual Overview ................................................................
PAGE 4
Stand Mode Sensitivity ................................................................................................................................................................................................41 Laser Pointer Control ....................................................................................................................................................................................................42 Laser Pointer Period ....................................................
PAGE 5
Example: Setting a Prefix ................................................................................................................................................................................... 96 Global AIM ID .................................................................................................................................................................................................................. 98 GS1-128 AIM ID ............................................................
PAGE 6
GS1 DataBar Expanded Enable/Disable .................................................................................................................................................... 150 GS1 DataBar Expanded GS1-128 Emulation ........................................................................................................................................... 150 GS1 DataBar Expanded Minimum Reads .........................................................................................................
PAGE 7
Datalogic 2 of 5 Minimum Reads .................................................................................................................................................................208 Datalogic 2 of 5 Decoding Level ..................................................................................................................................................................208 Datalogic 2 of 5 Length Control ......................................................................................
PAGE 8
Code 4 and Code 5 Common Configuration Items ........................................................................................................................................ 267 Code 4 and 5 Decoding Level ....................................................................................................................................................................... 267 Code 4 and Code 5 Minimum Reads ..............................................................................................
PAGE 9
Appendix E. Keypad ............................................................................................................... 323 Appendix F. Scancode Tables ................................................................................................. 327 Control Character Emulation ..................................................................................................................................................................................327 Single Press and Release Keys .......
PAGE 10
NOTES 8 PowerScan® PD7100 Corded
PAGE 11
Chapter 1 Introduction About this Guide This Product Reference Guide (PRG) is provided for users seeking advanced technical information, including connection, programming, maintenance and specifications. The Quick Reference Guide (QRG) and other publications associated with this product are downloadable free of charge from the website listed on the back cover of this manual. Typically, units are factory-programmed for the most common terminal and communications settings.
PAGE 12
Introduction Chapter 11, Symbologies defines options for all symbologies and provides the program- ming barcodes necessary for configuring these features. Appendix A, Technical Specifications lists physical and performance characteristics, as well as environmental and regulatory specifications. It also provides standard cable pinouts. Appendix B, Standard Defaults references common factory default settings for reader features and options.
PAGE 13
Technical Support Technical Support Datalogic Website Support The Datalogic website (www.scanning.datalogic.com) is the complete source for technical support and information for Datalogic products. The site offers product support, product registration, warranty information, product manuals, product tech notes, software updates, demos, and instructions for returning products for repair.
PAGE 14
Introduction NOTES 4 PowerScan® PBT7100 Cordless
PAGE 15
Chapter 2 Getting Started About the Reader Advancements in the LED technology used in this reader significantly improve the illumination of the target field of view, resulting in higher scan efficiency. Whether used in Single Trigger or Continuous Mode, the ergonomic design of the reader will help to promote comfortable handling during extended periods of use.
PAGE 16
Getting Started Setting Up the Reader and Base Station Follow the steps provided in this section to connect and get your reader up and communicating with its host: 1. Install the Battery in the Reader 2. Connect the Base Station 3. Select the Interface Type 4. Configure Interface Settings (only if not using factory settings for that interface) 5.
PAGE 17
Linking the Reader to a Base Station Host Connection — The interface type was specified at the time your reader was ordered, however you should verify before connection that the reader’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 2. Keyboard Wedge interface cables have a ‘Y’ connection where its female end mates with the male end of the cable from the keyboard and the remaining end at the keyboard port on the terminal/PC.
PAGE 18
Getting Started Figure 3. Labeling and Nomenclature This illustration shows label placement ONLY. For actual regulatory, patent and other applicable information, view the labels on the product intself, or call your nearest sales or service office.
PAGE 19
Paging Feature Paging Feature To help locate a missing reader, press the Base Station Link Button momentarily (less than one second). This will cause the reader to beep five times at its loudest volume setting. Programming The reader is typically factory-configured with a set of default features.
PAGE 20
Getting Started • USB-OEM Interface, starting on page 87 • IBM 46XX Interface, starting on page 89 Configure Other Features If your installation requires different programming than the standard factory default settings, the following sections of this manual allow configuration of non-interface-specific settings you might require: General Features — General Features includes programming for scanning, beeper and LED indicators and other such universal settings.
PAGE 21
Chapter 3 Interfaces Interface Selection Each reader model will support one of the following sets of host interfaces: General Purpose Models (5 volt supply) RS-232 RS-232 OPOS USB Keyboard Wedge Retail Point of Sale Models (4 to 14 volt supply) RS-232 RS-232 OPOS USB IBM 46XX Configuring the Interface Scan the programming barcode from this section which selects the appropriate interface type matching the system the reader will be connected to.
PAGE 22
Interfaces Table 1.
PAGE 23
Configuring the Interface KEYBOARD FEATURES AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key Encoding Select KBD-AT Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard Select KBD-AT-NK AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Select KBD-AT-ALT Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Set KEYBOARD WEDGE Interface Features starting on page 73 Select KBD-AT-ALT-NK PC/XT w
PAGE 24
Interfaces KEYBOARD — cont.
PAGE 25
Global Interface Features Global Interface Features The following interface features are configurable by all interface types. To set features specific to your interface, turn to that section of this manual: • RS-232 ONLY Interface on page 47 • Keyboard Interface on page 73 • USB-OEM Interface on page 87 • IBM 46XX Interface on page 89 Host Commands — Obey/Ignore This option specifies whether the reader will obey or ignore host commands.
PAGE 26
Interfaces USB Suspend Mode This setting enables/disables the ability of USB interfaces to enter suspend mode.
PAGE 27
Chapter 4 General Features Double Read Timeout To prevent a double read of the same label, the Double Read Timeout sets the minimum time allowed between reads of labels of the same symbology and data. If the unit reads a label and sees the same label again within the Double Read Timeout, the second read of the label will be ignored. Double Read Timeout does not apply to scan modes that require a trigger pull for each label that is read. ENTER/EXIT PROGRAMMING MODE Double Read Timeout = 0.
PAGE 28
General Features Double Read Timeout — continued ENTER/EXIT PROGRAMMING MODE Double Read Timeout = 0.5 Second Double Read Timeout = 0.6 Second Double Read Timeout = 0.7 Second Double Read Timeout = 0.8 Second Double Read Timeout = 0.
PAGE 29
Label Gone Timeout Label Gone Timeout This feature sets the time after the last label segment is seen before the reader prepares for a new label. The timeout can be set within a range of 10 milliseconds to 2,550 milliseconds (2.55 seconds) in 10ms increments. Follow these instructions to set this feature: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield three digits.
PAGE 30
General Features Label Gone Timeout — cont. ENTER/EXIT PROGRAMMING MODE Select Label Gone Timeout Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 31
Sleep Mode Timeout Sleep Mode Timeout Specifies the timeout value for the reader to enter low power Sleep Mode.
PAGE 32
General Features Sleep Mode Timeout — continued ENTER/EXIT PROGRAMMING MODE Sleep Mode Timeout = 5 Seconds Sleep Mode Timeout = 6 Seconds Sleep Mode Timeout = 7 Seconds Sleep Mode Timeout = 8 Seconds Sleep Mode Timeout = 9 Seconds Sleep Mode Timeout = 9.9 Seconds (9,900ms max.
PAGE 33
LED and Beeper Indicators LED and Beeper Indicators Power On Alert Disables or enables the indication (from the Beeper) that the reader is receiving power.
PAGE 34
General Features Good Read: When to Indicate This feature specifies when the reader will provide indication (beep and/or flash its green LED) upon successfully reading a barcode. Choices are: • Good Read = Indicate after decode • Good Read = Indicate after transmit • Good Read = Indicate after CTS goes inactive, then active This option, which uses CTS, is only valid for RS-232 interfaces.
PAGE 35
LED and Beeper Indicators Good Read Beep Type Specifies whether the good read beep has a mono or bitonal beep sound.
PAGE 36
General Features Good Read Beep Frequency Adjusts the good read beep to sound at a selectable low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.) ENTER/EXIT PROGRAMMING MODE Good Read Beep Frequency = Low Good Read Beep Frequency = Medium DEFAULT Good Read Beep Frequency = High Good Read Beep Length Specifies the duration of a good read beep.
PAGE 37
LED and Beeper Indicators Good Read Beep Length — continued ENTER/EXIT PROGRAMMING MODE DEFAULT Good Read Beep Length = 80 msec Good Read Beep Length = 100 msec Good Read Beep Length = 120 msec Good Read Beep Length = 140 msec Good Read Beep Length = 160 msec Good Read Beep Length = 180 msec Good Read Beep Length = 200 msec Product Reference Guide 27
PAGE 38
General Features Good Read Beep Volume Selects the beeper volume (loudness) upon a good read beep. There are three selectable volume levels.
PAGE 39
LED and Beeper Indicators Good Read LED Duration This feature specifies the amount of time that the Good Read LED remains on following a good read. The good read LED on time can be set within a range of 10 milliseconds to 2,550 milliseconds (0.001 to 2.55 seconds) in 10ms increments. Follow these instructions to set this feature: 1. Determine the desired setting in milliseconds. A setting of 0 means that the good read LED stays on until the next time the trigger is pulled. 2.
PAGE 40
General Features Good Read LED Duration — cont. ENTER/EXIT PROGRAMMING MODE Select Good Read LED Duration Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning. CANCEL DEFAULT 020 = Good Read LED stays on for 2 seconds. Indicators are dimmed during sleep.
PAGE 41
Scanning Features Scanning Features Scan Mode Selects the scan operating mode for the reader.
PAGE 42
General Features Scan Mode — continued ENTER/EXIT PROGRAMMING MODE DEFAULT Scan Mode = Trigger Single Scan Mode = Trigger Hold Multiple Scan Mode = Trigger Pulse Multiple Scan Mode = Flashing Scan Mode = Always On Scan Mode = Stand Mode Scan Mode = Trigger Object Sense 32 PowerScan® PBT7100 Cordless
PAGE 43
Scanning Features Stand Mode Triggered Timeout This feature specifies the time to remain in Trigger Single mode after the trigger is pulled while in Stand Mode. This timeout is only used when the Scan Mode is configured as Stand Mode. NOTE ENTER/EXIT PROGRAMMING MODE DEFAULT Stand Mode Triggered Timeout = 0.5 Seconds Stand Mode Triggered Timeout = 1.
PAGE 44
General Features Stand Mode Triggered Timeout — continued ENTER/EXIT PROGRAMMING MODE Stand Mode Triggered Timeout = 6 Seconds Stand Mode Triggered Timeout = 8 Seconds Stand Mode Triggered Timeout = Switch back to Trigger Single on trigger pull 34 PowerScan® PBT7100 Cordless
PAGE 45
Scanning Features Scanning Active Time This setting specifies the amount of time that the reader stays in scan ON state once the state is entered. The range for this setting is from 1 to 255 seconds in 1-second increments. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the result with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3. Scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4.
PAGE 46
General Features Scanning Active Time — cont. ENTER/EXIT PROGRAMMING MODE Select Scanning Active Time Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 47
Flash On Time Flash On Time This feature specifies the ON time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc. 3.
PAGE 48
General Features Flash On Time — cont. ENTER/EXIT PROGRAMMING MODE Select Flash ON Time Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 49
Flash Off Time Flash Off Time This feature specifies the OFF time for the indicator LED while in Flash Mode. The selectable range is 100 to 9,900 milliseconds (0.1 to 9.9 seconds), in 100 millisecond increments. Follow these instructions to set this feature. 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 100 (setting is in 100ms increments). Pad the result with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc. 3.
PAGE 50
General Features Flash Off Time — cont. ENTER/EXIT PROGRAMMING MODE Select Flash OFF Time Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 51
Stand Mode Sensitivity Stand Mode Sensitivity Sets the sensitivity level for stand mode wakeup. Choices are low, medium and high.
PAGE 52
General Features Laser Pointer Control The Laser Pointer is a value-added option which might not have been included when your reader was ordered. NOTE Specifies the amount of time that the laser pointer is turned on preliminary to scanning. When the trigger is pressed in Trigger Single Mode, the laser pointer will be activated for the time period configured by this feature. Immediately following this, the reader will start scanning.
PAGE 53
Laser Pointer Period Laser Pointer Period This option specifies the period of the laser pointer blink during scanning. The laser pointer will be activated for the time specified by Laser Pointer Control. then start blinking OFF then ON at 50% duty cycle for the duration set by Laser Pointer Period. ENTER/EXIT PROGRAMMING MODE Laser Pointer Period = Disable DEFAULT Laser Pointer Period = 500 ms Laser Pointer Period = 1 Second (1,000 ms) Laser Pointer Period = 1.
PAGE 54
General Features Laser Pointer Period — cont. Laser Pointer Period = 2.5 Seconds (2,500 ms) Laser Pointer Period = 3 Seconds (3,000 ms) Laser Pointer Period = 3.5 Seconds (3,500 ms) Laser Pointer Period = 4 Seconds (4,000 ms) Laser Pointer Period = 4.
PAGE 55
Green Spot Duration Green Spot Duration Specifies the duration of the good read pointer beam after a good read.
PAGE 56
General Features NOTES 46 PowerScan® PBT7100 Cordless
PAGE 57
Chapter 5 RS-232 ONLY Interface Introduction Use the programming barcodes in this chapter if modifications to the standard RS-232 interface settings are necessary to meet your system’s requirements. Additional settings which apply to both the RS-232 and USB interfaces are available in Chapter 6, RS-232/ USB-Com Interfaces. RS-232 Standard Factory Settings Reference Appendix B, Standard Defaults for a listing of standard factory settings.
PAGE 58
RS-232 ONLY Interface Baud Rate — continued ENTER/EXIT PROGRAMMING MODE DEFAULT Baud Rate = 9600 Baud Rate = 19,200 Baud Rate = 38,400 Baud Rate = 57,600 Baud Rate = 115,200 48 PowerScan® PBT7100 Cordless
PAGE 59
Data Bits Data Bits This parameter allows the reader to interface with devices requiring a 7-bit or 8-bit ASCII protocol for sending and receiving data.
PAGE 60
RS-232 ONLY Interface Stop Bits The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial data stream. The number of stop bits selected (one or two) depends on the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match host device requirements.
PAGE 61
Parity Parity This feature specifies parity required for sending and receiving data. A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements. • Select None when no parity bit is required. • Select Odd parity and the parity bit value is set to 0 or 1, based on data, to ensure that an odd number of 1 bits are contained in the coded character.
PAGE 62
RS-232 ONLY Interface Handshaking Control The data interface consists of an RS-232 port designed to operate either with or without the hardware handshaking lines, Request to Send (RTS), and Clear to Send (CTS). Handshaking Control includes the following options: • RTS — RTS is asserted during transmissions. CTS is ignored. • RTS/CTS — RTS is asserted during transmissions. CTS gates transmissions. • RTS/XON/XOFF — RTS is asserted during transmissions. CTS is ignored. XON and XOFF gate transmissions.
PAGE 63
Chapter 6 RS-232/USB-Com Interfaces Introduction The programming barcodes in this chapter allow modifications to the standard RS-232 and USB-Com interfaces. Standard Factory Settings Reference Appendix B, Standard Defaults for a listing of standard factory settings.
PAGE 64
RS-232/USB-Com Interfaces Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. To set the delay: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments). Pad the result with leading zeroes to yield two digits.
PAGE 65
Intercharacter Delay Intercharacter Delay — cont. ENTER/EXIT PROGRAMMING MODE Intercharacter Delay = No Delay Select Intercharacter Delay Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 66
RS-232/USB-Com Interfaces Beep On ASCII BEL When this parameter is enabled, the reader issues a beep when a character is detected on the RS-232 serial line. is issued to gain a user's attention to an illegal entry or other important event. ENTER/EXIT PROGRAMMING MODE DEFAULT Beep On ASCII BEL = Disable Beep On ASCII BEL = Enable Beep On Not on File This option enables/disables the action of the reader to sound a three beep sequence upon receiving a Not-On-File (NOF) host command.
PAGE 67
ACK NAK Options ACK NAK Options This enables/disables the ability of the reader to support the RS-232 ACK/NAK protocol. When configured, the reader and/or host sends an “ACK” when it receives data properly, and sends “NAK” when the data is in error. Options are: • Disable • Enable for label transmission — The reader expects an ACK/NAK response from the host when a label is sent. • Enable for host-command acknowledge — The reader will respond with ACK/NAK when the host sends a command.
PAGE 68
RS-232/USB-Com Interfaces ACK Character This setting specifies an ASCII character or hex value to be used as the ACK character. ASCII characters or any hex value from 0 to 0xFF can be selected. NOTE Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized when the option Data Bits has been set as 7 Data Bits. To set this feature: 1. Determine the desired character or value. 2.
PAGE 69
ACK NAK Options ACK Character — cont.
PAGE 70
RS-232/USB-Com Interfaces NAK Character This setting specifies an ASCII character or hex value to be used as the NAK character. ASCII characters or any hex value from 0 to 0xFF can be selected. NOTE Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized when the option Data Bits has been set as 7 Data Bits. To set this feature: 1. Determine the desired character or value. 2.
PAGE 71
ACK NAK Options NAK Character — cont.
PAGE 72
RS-232/USB-Com Interfaces ACK NAK Timeout Value This option specifies the amount of time the reader waits for an ACK character from the host following label transmission. The selectable timeout range is 200 milliseconds to 15,000ms (15 seconds) in 200ms increments. A selection of 0 disables the timeout. To set this value: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 200 (setting is in 200ms increments). Pad the result with leading zeroes to yield two digits.
PAGE 73
ACK NAK Options ACK NAK Timeout Value — cont. ENTER/EXIT PROGRAMMING MODE Select ACK NAK Timeout Value Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 74
RS-232/USB-Com Interfaces ACK NAK Retry Count This feature specifies the number of times the reader retries a label transmission due to a retry condition. The selectable range is from 1 to 254 retries. A selection of 0 disables the count, and a selection of 255 specifies unlimited retries. To set this feature: 1. Determine the desired setting. 2. Pad the number with leading zeroes to yield three digits. For example: 0 = 000, 5 = 005, 20 = 020, etc. 3.
PAGE 75
ACK NAK Options ACK NAK Retry Count — cont. ENTER/EXIT PROGRAMMING MODE Select ACK NAK Retry Count Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 76
RS-232/USB-Com Interfaces ACK NAK Error Handling This feature specifies the method the reader uses to handle receive errors detected while waiting for an ACK character from the host.
PAGE 77
Indicate Transmission Failure Indicate Transmission Failure This option enables/disables the reader’s ability to sound an error beep to indicate a transmission failure while in ACK/NAK mode.
PAGE 78
RS-232/USB-Com Interfaces Disable Character Specifies the value of the RS-232 host command used to disable the reader. ASCII characters or any hex value from 0 to 0xFF can be selected. NOTE Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized when the option Data Bits has been set as 7 Data Bits. To set the value: 1. Determine the desired character or value.
PAGE 79
Disable Character Disable Character — cont.
PAGE 80
RS-232/USB-Com Interfaces Enable Character Specifies the value of the RS-232 host command used to enable the reader. ASCII characters or any hex value from 0 to 0xFF can be selected. NOTE Setting to previously defined characters such as XON, XOFF, or host commands conflicts with normal operation of these characters. 8-bit data is not recognized when the option Data Bits has been set as 7 Data Bits. To set this feature: Determine the desired character or value.
PAGE 81
Enable Character Enable Character — cont.
PAGE 82
RS-232/USB-Com Interfaces NOTES 72 PowerScan® PBT7100 Cordless
PAGE 83
Chapter 7 Keyboard Interface Introduction Use the programming barcodes in this chapter to select options for USB Keyboard and Wedge Interfaces. Standard Factory Settings Reference Appendix B, Standard Defaults for a listing of standard factory settings. Scancode Tables Information about control character emulation which applies to keyboard interfaces is listed in Appendix F, Scancode Tables.
PAGE 84
Keyboard Interface Country Mode This feature specifies the country/language supported by the keyboard. Only the following interfaces support ALL Country Modes.
PAGE 85
Country Mode Country Mode — continued ENTER/EXIT PROGRAMMING MODE Supports only the interfaces listed in theCountry Mode feature description. Country Mode = Denmark Country Mode = France Country Mode = Germany Supports only the interfaces listed in theCountry Mode feature description. Country Mode = Hungary Country Mode = Italy Supports only the interfaces listed in theCountry Mode feature description.
PAGE 86
Keyboard Interface Country Mode — continued ENTER/EXIT PROGRAMMING MODE Supports only the interfaces listed in theCountry Mode feature description. Country Mode = Poland Supports only the interfaces listed in theCountry Mode feature description. Country Mode = Portugal Supports only the interfaces listed in theCountry Mode feature description. Country Mode = Romania Supports only the interfaces listed in theCountry Mode feature description.
PAGE 87
Caps Lock State Caps Lock State This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alternate key encoding keyboard is selected. ENTER/EXIT PROGRAMMING MODE DEFAULT Caps Lock State = Caps Lock OFF Caps Lock State = Caps Lock ON Caps Lock State = AUTO Caps Lock Enable Numlock This option specifies the setting of the Numbers Lock (Numlock) key while in keyboard wedge interface.
PAGE 88
Keyboard Interface Send Control Characters This feature Specifies how the reader transmits ASCII control characters to the host. Reference Appendix F, Scancode Tables for more information about control characters. Options are as follows: Control Character 00 — Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1.
PAGE 89
Wedge Quiet Interval Wedge Quiet Interval This option specifies the amount of time to look for keyboard activity before the reader breaks the keyboard connection in order to transmit data to host. The selectable range for this feature is from 0 to 990ms in 10ms increments. This feature applies ONLY to the Keyboard Wedge interface. NOTE Follow these instructions to set this feature: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments).
PAGE 90
Keyboard Interface Wedge Quiet Interval — cont. ENTER/EXIT PROGRAMMING MODE Select Wedge Quiet Interval Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 91
Intercharacter Delay Intercharacter Delay This parameter specifies the intercharacter delay between the end of one character and the beginning of the next. The delay can be set within a range of zero (0) to 990 milliseconds in 10ms increments. A setting of zero specifies no delay. This feature applies ONLY to the Keyboard Wedge interface. NOTE To set the delay: 1. Determine the desired setting in milliseconds. 2. Divide the desired setting by 10 (setting is in 10ms increments).
PAGE 92
Keyboard Interface Intercharacter Delay — cont. ENTER/EXIT PROGRAMMING MODE Intercharacter Delay = No Delay Select Intercharacter Delay Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 93
Intercode Delay Intercode Delay Specifies the delay between labels transmitted to the host for this interface. The selectable range for this feature is from 0 to 99 seconds. Follow these instructions to set this feature: 1. Determine the desired setting. 2. Pad the number with leading zeroes to yield two digits. For example: 0 = 00, 5 = 05, 20 = 20, etc 3. Scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4. Scan the barcode: SELECT INTERCODE DELAY SETTING. 5.
PAGE 94
Keyboard Interface Intercode Delay — cont. ENTER/EXIT PROGRAMMING MODE Set Intercode Delay Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 95
USB Keyboard Speed USB Keyboard Speed This option specifies the USB poll rate for a USB keyboard. This feature applies ONLY to the USB Keyboard interface.
PAGE 96
Keyboard Interface USB Keyboard Speed — continued ENTER/EXIT PROGRAMMING MODE USB Keyboard Speed = 6ms USB Keyboard Speed = 7ms USB Keyboard Speed = 8ms USB Keyboard Speed = 9ms USB Keyboard Speed = 10ms 86 PowerScan® PBT7100 Cordless
PAGE 97
Chapter 8 USB-OEM Interface Introduction Feature settings for USB interfaces differ depending upon which host type the reader will be connected with. Use the feature settings in this chapter and Chapter 9, IBM 46XX Interface to specifically configure for the USB-OEM interface. Other USB interfaces are included in the approprite chapter for their host type. Standard Factory Settings Reference Appendix B, Standard Defaults for a listing of standard factory settings.
PAGE 98
USB-OEM Interface USB-OEM Device Usage The USB-OEM protocol allows for the reader to be identified as one of two different types of barcode scanners. Depending on what other scanners you may already have connected to a USB-OEM POS, you may need to change this setting to enable all devices to communicate. Options are: • Table Top Scanner • Handheld Scanner It may be necessary to switch device usage when connecting two readers/scanners of the same type to a POS system.
PAGE 99
Chapter 9 IBM 46XX Interface Introduction Use the barcodes in this section to configure programmable features for available IBM 46XX interfaces. IBM Standard Factory Settings Reference Appendix B, Standard Defaults for a listing of standard factory settings.
PAGE 100
IBM 46XX Interface 46xx Number of Host Resets Specifies how many consecutive resets are processed before the reader starts a five-second period to allow the user to enter Programming Mode and configure the reader. The configurable range for this feature is 1 to 15 resets.
PAGE 101
46xx Number of Host Resets 46xx Number of Host Resets — cont.
PAGE 102
IBM 46XX Interface 46xx Number of Host Resets — cont.
PAGE 103
Transmit Labels in Code 39 Format Transmit Labels in Code 39 Format This feature enable/disables translation to Code 39 before transmitting label data to an IBM-46XX or a USB-OEM host. Only the symbology identifier is modified for the translation. The data is not converted to Code 39 or verified to be valid for Code 39. Options are: IBM Standard Format — Code 39 Format — Send labels in standard IBM format.
PAGE 104
IBM 46XX Interface NOTES 94 PowerScan® PBT7100 Cordless
PAGE 105
Chapter 10 Data Editing Data Editing Overview It is not recommended to use these features with IBM interfaces. CAUTION When a barcode is scanned, additional information can be sent to the host computer along with the barcode data. This combination of barcode data and supplementary userdefined data is called a “message string.” The features in this chapter can be used to build specific user-defined data into a message string.
PAGE 106
Data Editing Please Keep In Mind... • Modifying a message string is not a mandatory requirement. Data editing is sophisticated feature allowing highly customizable output for advanced users. Factory default settings for data editing is typically set to NONE. • A prefix or suffix may be applied (reference the Symbologies chapter for these settings) across all symbologies (set via the Global features in this chapter).
PAGE 107
Global Prefix/Suffix 6. Scan the ENTER/EXIT barcode once again to exit Programming Mode. 7. The resulting message string would appear as follows: Scanned barcode data:12345 Resulting message string output: $12345 This option sets up to 20 characters each from the set of ASCII characters or any hex value from 00 to FF.
PAGE 108
Data Editing Global AIM ID This feature enables/disables addition of AIM IDs for all symbology types. NOTE AIM label identifiers (as opposed to custom characters you select yourself as with label identifiers) can be included with scanned barcode data. AIM label identifiers consist of three characters as follows: • A close brace character (ASCII ‘]’), followed by... • A code character (see the table below), followed by... • A modifier character (the modifier character is symbol dependent).
PAGE 109
Global AIM ID Global AIM ID — continued ENTER/EXIT PROGRAMMING MODE DEFAULT Global AIM ID = Disable Global AIM ID = Enable Product Reference Guide 99
PAGE 110
Data Editing GS1-128 AIM ID If Global AIM ID is disabled, the AIM ID for GS1-128 can be enabled/disabled independently. The AIM ID for GS1-128 is a ]C1, ]C2 or ]C3. AIM IDs for other symbologies can be enabled/disabled independently as well. Contact Customer Support for assistance.
PAGE 111
Label ID Label ID A Label ID is a customizable code of up to three ASCII characters (each can be one of hex 0x01-0xFF), used to identify a barcode (symbology) type. It can be appended previous to or following the transmitted barcode data depending upon how this option is enabled. This feature provides options for configuring custom Label IDs as a pre-loaded set (see Label ID: Pre-loaded Sets on page 101) or individually per symbology (see Label ID: Set Individually Per Symbology on page 103).
PAGE 112
Data Editing Symbology Default Label ID set CODE128 # 230000 T 540000 CODE39 * 2A0000 V 560000 CODE4 4 340000 4 340000 CODE5 j 6A0000 j 6A0000 CODE93 & 260000 U 550000 GS1 DATABAR OMNIDIRECTIONAL R4 523400 u 750000 GS1 DATABAR EXPANDED RX 525800 t 740000 GS1 DATABAR LIMITED RL 524C00 v 760000 s 730000 s 730000 000000 k 6B0000 DATALOGIC 2OF5 GS1-128 102 Alternate Label ID set EAN13 F 460000 B 420000 EAN13 P2 F 460000 L 4C0000 EAN13 P5 F 460000
PAGE 113
Label ID Label ID: Set Individually Per Symbology To configure a Label ID individually for a single symbology: 1. Scan the ENTER/EXIT barcode. 2. Select Label ID position as either BEFORE (Enable as Prefix) or AFTER (Enable as suffix) by scanning the appropriate barcode in the section Label ID Control on page 105. Reference Figure 7 for Label ID positioning options if multiple identification features are enabled. 3.
PAGE 114
Data Editing Label ID — continued Table 18. Label ID Examples STEP ACTION 1. Scan the ENTER/EXIT barcode 2. Determine placement of the Label ID characters BEFORE or AFTER with regard to scanned data using EXAMPLES (Scanner enters Programming Mode) Enable as Prefix Enable as Suffix Enable as Prefix Enable as Suffix GS1 DataBar Omnidirectional Code 39 Interleaved 2 of 5 Code 32 Label ID Control on page 105 3.
PAGE 115
Label ID Label ID — continued Label ID Control This option controls whether a Label ID is disabled, or sent as a prefix or suffix for a given symbology type. ENTER/EXIT PROGRAMMING MODE DEFAULT Label ID Transmission = Disable Label ID Transmission = Enable as Prefix Label ID Transmission = Enable as Suffix Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 116
Data Editing Label ID — continued Label ID Symbology Selection This option selects the symbology for which a Label ID is to be configured. See Label ID on page 101 for full instructions.
PAGE 117
Label ID Label ID — continued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See Label ID on page 101 for full instructions.
PAGE 118
Data Editing Label ID — continued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See Label ID on page 101 for full instructions.
PAGE 119
Label ID Label ID — continued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See Label ID on page 101 for full instructions.
PAGE 120
Data Editing Label ID — continued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See Label ID on page 101 for full instructions.
PAGE 121
Label ID Label ID — continued Label ID Symbology Selection — continued This option selects the symbology for which a Label ID is to be configured. See Label ID on page 101 for full instructions.
PAGE 122
Data Editing Case Conversion This feature allows conversion of the case of all alphabetic characters to upper or lower case. Case conversion affects ONLY scanned barcode data, and does not affect Label ID, Prefix, Suffix, or other appended data.
PAGE 123
Character Conversion Character Conversion Character conversion is an eight byte configuration item. The eight bytes are 4 character pairs represented in hexadecimal ASCII values. The first character in the pair is the character that will be converted. The second character in the pair is the character to convert to. If the character to convert in a pair is FF, then no conversion is done.
PAGE 124
Data Editing Character Conversion — continued ENTER/EXIT PROGRAMMING MODE Configure Character Conversion DEFAULT 114 0xFFFFFFFFFFFFFFFF (No character conversion) PowerScan® PBT7100 Cordless
PAGE 125
Chapter 11 Symbologies Introduction The reader supports the following symbologies (barcode types). Options for each symbology are included in this chapter.
PAGE 126
Symbologies Coupon Control This feature is used to control the method of processing coupon labels. Options are: • Disable coupon decoding • Enable UPC-A coupon decoding • Enable GS1 DataBar coupon decoding To set this feature: 1. Scan the SWITCH bar code. 2. Scan either the enable or disable bar code below. You’ll need to cover any unused barcodes on this and the facing page to ensure that the reader sees only the barcode you intend to scan. 3.
PAGE 127
UPC-A UPC-A The following options apply to the UPC-A symbology. UPC-A Enable/Disable When disabled, the reader will not read UPC-A barcodes. ENTER/EXIT PROGRAMMING MODE UPC-A = Disable DEFAULT UPC-A = Enable UPC-A Check Character Transmission Enable this option to transmit the check character along with UPC-A barcode data.
PAGE 128
Symbologies UPC-A — cont. Expand UPC-A to EAN-13 Expands UPC-A data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. ENTER/EXIT PROGRAMMING MODE DEFAULT UPC-A to EAN-13 = Don’t Expand UPC-A to EAN-13 = Expand UPC-A Number System Character Transmission This feature enables/disables transmission of the UPC-A number system character.
PAGE 129
UPC-A UPC-A — cont. In-Store Minimum Reads This feature specifies the minimum number of consecutive times an in-store label must be decoded before it is accepted as good read. In-store labels are defined as UPC-A labels with a number-system character of 2 or 4 as well as EAN 8 and EAN 13 labels with a Flag1 character of 2 or an EAN 13 label starting with the three characters '980'.
PAGE 130
Symbologies UPC-E The following options apply to the UPC-E symbology. UPC-E Enable/Disable When disabled, the reader will not read UPC-E barcodes. ENTER/EXIT PROGRAMMING MODE UPC-E = Disable DEFAULT UPC-E = Enable UPC-E Check Character Transmission Enable this option to transmit the check character along with UPC-E barcode data.
PAGE 131
UPC-E UPC-E — cont. Expand UPC-E to EAN-13 Expands UPC-E data to the EAN-13 data format. Selecting this feature also changes the symbology ID to match those required for EAN-13. ENTER/EXIT PROGRAMMING MODE DEFAULT UPC-E to EAN-13 = Don’t Expand UPC-E to EAN-13 = Expand Expand UPC-E to UPC-A Expands UPC-E data to the UPC-A data format.
PAGE 132
Symbologies UPC-E — cont. UPC-E Number System Character Transmission This feature enables/disables transmission of the UPC-E system number character.
PAGE 133
UPC-E UPC-E — cont. UPC-E Minimum Reads This feature specifies the minimum number of consecutive times a UPC-E label must be decoded before it is accepted as good read..
PAGE 134
Symbologies GTIN Formatting This feature enables/disables the ability to convert UPC-E, UPC-A, EAN 8, and EAN 13 labels into the GTIN 14-character format. If add-on information is present on the base label prior to the conversion taking place, the addon information will be appended to the converted GTIN label.
PAGE 135
EAN 13 EAN 13 The following options apply to the EAN 13 (Jan 13) symbology. EAN 13 Enable/Disable When disabled, the reader will not read EAN 13/JAN 13 barcodes. ENTER/EXIT PROGRAMMING MODE EAN 13 = Disable DEFAULT EAN 13 = Enable EAN 13 Check Character Transmission Enable this option to transmit the check character along with EAN 13 barcode data.
PAGE 136
Symbologies EAN 13 — cont. EAN-13 Flag 1 Character Enables/disables transmission of an EAN/JAN13 Flag1 character. The Flag 1 character is the first character of the label.
PAGE 137
EAN 13 EAN-13 ISBN Conversion This option enables/disables conversion of EAN 13/JAN 13 Bookland labels starting with 978 to ISBN labels.
PAGE 138
Symbologies EAN 13 — cont. EAN 13 Minimum Reads This feature specifies the minimum number of consecutive times an EAN 13 label must be decoded before it is accepted as good read..
PAGE 139
EAN 8 EAN 8 The following options apply to the EAN 8 (Jan 8) symbology. EAN 8 Enable/Disable When disabled, the reader will not read EAN 8/JAN 8 barcodes. ENTER/EXIT PROGRAMMING MODE EAN 8 = Disable DEFAULT EAN 8 = Enable EAN 8 Check Character Transmission Enable this option to transmit the check character along with EAN 8 barcode data.
PAGE 140
Symbologies EAN 8 — cont. Expand EAN 8 to EAN 13 Enable this option to expand EAN 8/JAN 8 labels to EAN 13/JAN 13.
PAGE 141
EAN 8 EAN 8 — cont. EAN 8 Minimum Reads This feature specifies the minimum number of consecutive times an EAN 8 (Jan 8) label must be decoded before it is accepted as good read..
PAGE 142
Symbologies UPC/EAN Global Settings This section provides configuration settings for UPC-A, UPC-E, EAN 13 and EAN 8 symbologies, and affects all of these unless otherwise marked for each feature description. UPC/EAN Decoding Level Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs.
PAGE 143
UPC/EAN Global Settings UPC/EAN Global Settings — cont. UPC/EAN Decoding Level — cont.
PAGE 144
Symbologies UPC/EAN Global Settings — cont. UPC/EAN Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 145
UPC/EAN Global Settings UPC/EAN Global Settings — cont. UPC/EAN Price Weight Check This feature enables/disables calculation and verification of price/weight check digits.
PAGE 146
Symbologies UPC/EAN Global Settings — cont. UPC-A Minimum Reads This feature specifies the minimum number of consecutive times a UPC-A label must be decoded before it is accepted as good read..
PAGE 147
Add-Ons Add-Ons The following features apply to optional add-ons. Contact Customer Support for advanced programming of optional and conditional add-ons. NOTE Optional Add-ons The reader can be enabled to optionally read the following add-ons (supplementals): • P2 • P5 • GS1-128 If a UPC/EAN base label and a an add-on are both decoded, the reader will transmit the base label and add-on. If a UPC/EAN base label is decoded without an add-on, the base label will be transmitted without an add-on.
PAGE 148
Symbologies Add-Ons — cont. Optional Add-ons — cont.
PAGE 149
Add-Ons Add-Ons — cont. Optional Add-On Timer This option sets the time the reader will look for an add-on when an add-on fragment has been seen and optional add-ons are enabled. (Also see Optional GS1-128 Add-On Timer on page 142.
PAGE 150
Symbologies Add-Ons — cont. Optional Add-On Timer — cont.
PAGE 151
Add-Ons Add-Ons — cont. Optional Add-On Timer — cont.
PAGE 152
Symbologies Add-Ons — cont. Optional GS1-128 Add-On Timer This option sets the timer expiration value to read the added part after reading the linear EAN/UPC part. For UPC/EAN add-ons other than those of that type, see Optional Add-On Timer on page 139.
PAGE 153
Add-Ons Add-Ons — cont. Optional GS1-128 Add-On Timer — cont.
PAGE 154
Symbologies Add-Ons — cont. Optional GS1-128 Add-On Timer — cont.
PAGE 155
Add-Ons Add-Ons — cont. P2 Add-Ons Minimum Reads This feature specifies the minimum number of times a P2 add-on must be read before it is marked as valid and then combined with a base label.
PAGE 156
Symbologies Add-Ons — cont. P5 Add-Ons Minimum Reads This feature specifies the minimum number of times a P5 add-on must be read before it is marked as valid and then combined with a base label.
PAGE 157
Add-Ons Add-Ons — cont. GS1-128 Add-Ons Minimum Reads This feature specifies the minimum number of times an GS1-128 add-on must be read before it is marked as valid and then combined with a base label.
PAGE 158
Symbologies GS1 DataBar Omnidirectional The following options apply to the GS1 DataBar Omnidirectional (formerly RSS-14) symbology. GS1 DataBar Omnidirectional Enable/Disable When disabled, the reader will not read GS1 DataBar Omnidirectional barcodes.
PAGE 159
GS1 DataBar Omnidirectional GS1 DataBar Omnidirectional — cont. GS1 DataBar Omnidirectional Minimum Reads This feature specifies the minimum number of consecutive times a GS1 DataBar Omnidirectional label must be decoded before it is accepted as good read.
PAGE 160
Symbologies GS1 DataBar Expanded The following options apply to the GS1 DataBar Expanded (formerly RSS Expanded) symbology. GS1 DataBar Expanded Enable/Disable When disabled, the reader will not read GS1 DataBar Expanded barcodes. ENTER/EXIT PROGRAMMING MODE DEFAULT GS1 DataBar Expanded = Disable GS1 DataBar Expanded = Enable GS1 DataBar Expanded GS1-128 Emulation When enabled, GS1 DataBar Expanded barcodes will be translated to the GS1-128 label data format.
PAGE 161
GS1 DataBar Expanded GS1 DataBar Expanded — cont. GS1 DataBar Expanded Minimum Reads This feature specifies the minimum number of consecutive times a GS1 DataBar Expanded label must be decoded before it is accepted as good read.
PAGE 162
Symbologies GS1 DataBar Expanded — cont. GS1 DataBar Expanded Length Control This feature specifies either variable length decoding or fixed length decoding for the GS1 DataBar Expanded symbology. Variable Length — Fixed Length — For variable-length decoding, a minimum length may be set. For fixed-length decoding, two different lengths may be set.
PAGE 163
GS1 DataBar Expanded GS1 DataBar Expanded — cont. GS1 DataBar Expanded Set Length 1 This feature specifies one of the barcode lengths for GS1 DataBar Expanded Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 74 characters. Follow these instructions to set this feature: 1. Determine the desired character length (from 1 to 74).
PAGE 164
Symbologies GS1 DataBar Expanded — cont. GS1 DataBar Expanded Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select GS1 DataBar Expanded Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 165
GS1 DataBar Expanded GS1 DataBar Expanded — cont. GS1 DataBar Expanded Set Length 2 This feature specifies one of the barcode lengths for GS1 DataBar Expanded Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 74 characters. A setting of 0 specifies to ignore this length (only one fixed length).
PAGE 166
Symbologies GS1 DataBar Expanded — cont. GS1 DataBar Expanded Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select GS1 DataBar Expanded Set Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 167
GS1 DataBar Limited GS1 DataBar Limited The following options apply to the GS1 DataBar Limited (formerly RSS Limited) symbology. GS1 DataBar Limited Enable/Disable When disabled, the reader will not read GS1 DataBar Limited barcodes. ENTER/EXIT PROGRAMMING MODE DEFAULT GS1 DataBar Limited = Disable GS1 DataBar Limited = Enable GS1 DataBar Limited GS1-128 Emulation When enabled, GS1 DataBar Limited barcodes will be translated to the GS1-128 label data format.
PAGE 168
Symbologies GS1 DataBar Limited — cont. GS1 DataBar Limited Minimum Reads This feature specifies the minimum number of consecutive times a GS1 DataBar Limited label must be decoded before it is accepted as good read.
PAGE 169
Code 39 Code 39 The following options apply to the Code 39 symbology. Code 39 Enable/Disable When disabled, the reader will not read Code 39 barcodes.
PAGE 170
Symbologies Code 39 — cont. Code 39 Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Code 39 check character.
PAGE 171
Code 39 Code 39 — cont. Code 39 Check Character Transmission Enable this option to transmit the check character along with Code 39 barcode data. ENTER/EXIT PROGRAMMING MODE Code 39 Check Character Transmission = Don’t Send DEFAULT Code 39 Check Character Transmission = Send Code 39 Start/Stop Character Transmission Enable this option to enable/disable transmission of Code 39 start and stop characters.
PAGE 172
Symbologies Code 39 — cont. Code 39 Full ASCII In Code 39 decoding, this enables/disables the translation of Code 39 characters to Code 39 full-ASCII characters.
PAGE 173
Code 39 Code 39 — cont. Code 39 Quiet Zones This feature specifies the number of quiet zones for Code 39 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the label.
PAGE 174
Symbologies Code 39 — cont. Code 39 Minimum Reads This feature specifies the minimum number of consecutive times a Code 39 label must be decoded before it is accepted as good read..
PAGE 175
Code 39 Code 39 — cont. Code 39 Decoding Level Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a very conservative decoder at the expense of not being able to read poorly printed or damaged labels. • Choosing Level 5 results in a very aggressive decoder.
PAGE 176
Symbologies Code 39 — cont. Code 39 Decoding Level — cont.
PAGE 177
Code 39 Code 39 — cont. Code 39 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 39 symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 178
Symbologies Code 39 — cont. Code 39 Set Length 1 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 0 to 50 characters. Follow these instructions to set this feature: 1. Determine the desired character length (from 0 to 50). Pad the number with leading zeroes to yield two digits.
PAGE 179
Code 39 Code 39 — cont. Code 39 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 39 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 180
Symbologies Code 39 — cont. Code 39 Set Length 2 This feature specifies one of the barcode lengths for Code 39 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check, data, and full-ASCII shift characters. The length does not include start/stop characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
PAGE 181
Code 39 Code 39 — cont. Code 39 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 39Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 182
Symbologies Code 39 — cont. Code 39 Interdigit Ratio This feature specifies the ratio between an intercharacter space and module for Code 39 labels.
PAGE 183
Code 39 Code 39 — cont. Code 39 Interdigit Ratio — cont.
PAGE 184
Symbologies Code 39 — cont. Code 39 Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 185
Code 39 Code 39 Stitching This option enables/disables stitching for Code 39 labels. When parts of a Code 39 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 186
Symbologies Code 32 The following options apply to the Code 32 (Italian Pharamaceutical Code) symbology. Code 32 Enable/Disable When disabled, the reader will not read Code 32 barcodes.
PAGE 187
Code 32 Code 32 — cont. Code 32 Check Character Transmission Enable this option to transmit the check character along with Code 32 barcode data. ENTER/EXIT PROGRAMMING MODE DEFAULT Code 32 Check Character Transmission = Don’t Send Code 32 Check Character Transmission = Send Code 32 Start/Stop Character Transmission This option enables/disable transmission of Code 32 start and stop characters.
PAGE 188
Symbologies Code 128 The following options apply to the Code 128 symbology. Code 128 Enable/Disable When disabled, the reader will not read Code 128 barcodes. ENTER/EXIT PROGRAMMING MODE Code 128 = Disable DEFAULT Code 128 = Enable Expand Code 128 to Code 39 This feature enables/disables expansion of Code 128 labels to Code 39 labels.
PAGE 189
Code 128 Code 128 — cont. Code 128 Check Character Transmission Enable this option to transmit the check character along with Code 128 barcode data. ENTER/EXIT PROGRAMMING MODE DEFAULT Code 128 Check Character Transmission = Don’t Send Code 128 Check Character Transmission = Send Code 128 Function Character Transmission Enables/disables transmission of Code128 function characters 1, 2, 3, and 4.
PAGE 190
Symbologies Code 128 — cont. Code 128 Sub-Code Change Transmission Enables/disables the transmission of “Sub-Code exchange” characters (NOT transmitted by standard decoding).
PAGE 191
Code 128 Code 128 — cont. Code 128 Quiet Zones This feature specifies the number of quiet zones for Code 128 labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the label.
PAGE 192
Symbologies Code 128 — cont. Code 128 Minimum Reads This feature specifies the minimum number of consecutive times a Code 128 label must be decoded before it is accepted as good read..
PAGE 193
Code 128 Code 128 — cont. Code 128 Decoding Level Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a very conservative decoder at the expense of not being able to read poorly printed or damaged labels. • Choosing Level 5 results in a very aggressive decoder.
PAGE 194
Symbologies Code 128 — cont. Code 128 Decoding Level — cont.
PAGE 195
Code 128 Code 128 — cont. Code 128 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 128 symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 196
Symbologies Code 128 — cont. Code 128 Set Length 1 This feature specifies one of the barcode lengths for Code 128 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 80 characters. Follow these instructions to set this feature: 1. Determine the desired character length (from 1 to 80). Pad the number with leading zeroes to yield two digits.
PAGE 197
Code 128 Code 128 — cont. Code 128 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 128 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 198
Symbologies Code 128 — cont. Code 128 Set Length 2 This feature specifies one of the barcode lengths for Code 128 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s data characters only. The length can be set from 1 to 80 characters. A setting of 0 specifies to ignore this length (only one fixed length). Follow these instructions to set this feature: 1.
PAGE 199
Code 128 Code 128 — cont. Code 128 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 128 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 200
Symbologies Code 128 — cont. Code 128 Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 201
Code 128 Code 128 — cont. Code 128 Stitching This option enables/disables stitching for Code 128 labels. When parts of a Code 128 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 202
Symbologies GS1-128 The following options apply to the GS1-128 symbology. (Also known as USS-128, GTIN-128, UCC-128, EAN 128.) GS1-128 Enable This option enables/disables the ability of the reader to translate GS1-128 labels to the GS1-128 data format. Options are: • Transmit GS1-128 labels in Code 128 data format. • Transmit GS1-128 labels in GS1-128 data format. • Do not transmit GS1-128 labels.
PAGE 203
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) The following options apply to the I 2 of 5 symbology. I 2 of 5 Enable/Disable When disabled, the reader will not read I 2 of 5 barcodes.
PAGE 204
Symbologies Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional I 2 of 5 check character.
PAGE 205
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Check Character Transmission Enable this option to transmit the check character along with I 2 of 5 barcode data.
PAGE 206
Symbologies Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Minimum Reads This feature specifies the minimum number of consecutive times an I 2 of 5 label must be decoded before it is accepted as good read..
PAGE 207
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Decoding Level This configuration item applies to Interleaved 2 of 5, Datalogic 2 of 5 and Standard 2 of 5. NOTE Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a very conservative decoder at the expense of not being able to read poorly printed or damaged labels.
PAGE 208
Symbologies Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Decoding Level — cont.
PAGE 209
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the I 2 of 5 symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 210
Symbologies Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters in increments of two. Follow these instructions to set this feature: 1. Determine the desired character length (from 2 to 50).
PAGE 211
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) — cont. Datalogic 2 of 5 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select I 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 212
Symbologies Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for I 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Follow these instructions to set this feature: 1.
PAGE 213
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select I 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 214
Symbologies Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 215
Interleaved 2 of 5 (I 2 of 5) Interleaved 2 of 5 (I 2 of 5) — cont. I 2 of 5 Stitching This option enables/disables stitching for I 2 of 5 labels. When parts of a I 2 of 5 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 216
Symbologies Datalogic 2 of 5 The following options apply to the Datalogic 2 of 5 symbology. Datalogic 2 of 5 Enable/Disable When disabled, the reader will not read Datalogic 2 of 5 barcodes.
PAGE 217
Datalogic 2 of 5 Datalogic 2 of 5 — cont. Datalogic 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional Datalogic 2 of 5 check character.
PAGE 218
Symbologies Datalogic 2 of 5 — cont. Datalogic 2 of 5 Minimum Reads This feature specifies the minimum number of consecutive times an Datalogic 2 of 5 label must be decoded before it is accepted as good read. ENTER/EXIT PROGRAMMING MODE DEFAULT I 2 of 5 Minimum Reads = 1 I 2 of 5 Minimum Reads = 2 I 2 of 5 Minimum Reads = 3 I 2 of 5 Minimum Reads = 4 Datalogic 2 of 5 Decoding Level The Datalogic 2 of 5 Decoding Level feature is set using I 2 of 5 Decoding Level on page 197.
PAGE 219
Datalogic 2 of 5 Datalogic 2 of 5 — cont. Datalogic 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Datalogic 2 of 5 symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 220
Symbologies Datalogic 2 of 5 — cont. Datalogic 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Datalogic 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters in increments of two. Follow these instructions to set this feature: 1. Determine the desired character length (from 2 to 50).
PAGE 221
Datalogic 2 of 5 Datalogic 2 of 5 — cont. Datalogic 2 of 5 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Datalogic 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 222
Symbologies Datalogic 2 of 5 — cont. Datalogic 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Datalogic 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Follow these instructions to set this feature: 1.
PAGE 223
Datalogic 2 of 5 Datalogic 2 of 5 — cont. Datalogic 2 of 5 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Datalogic 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 224
Symbologies Datalogic 2 of 5 — cont. Datalogic 2 of 5 Interdigit Maximum Ratio This feature specifies the maximum ratio between intercharacter space and module for Datalogic 2 of 5.
PAGE 225
Datalogic 2 of 5 Datalogic 2 of 5 Interdigit Maximum Ratio — cont.
PAGE 226
Symbologies Datalogic 2 of 5 — cont. Datalogic 2 of 5 Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 227
Datalogic 2 of 5 Datalogic 2 of 5 — cont. Datalogic 2 of 5 Stitching This option enables/disables stitching for Datalogic 2 of 5 labels. When parts of a Datalogic 2 of 5 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 228
Symbologies Codabar The following options apply to the Codabar symbology. Codabar Enable/Disable When disabled, the reader will not read Codabar barcodes.
PAGE 229
Codabar Codabar — cont. Codabar Check Character Calculation Enable this option to enables/disables calculation and verification of an optional Codabar check character. When disabled, any check character in the label is treated as a data character ENTER/EXIT PROGRAMMING MODE DEFAULT Codabar Check Character Calculation = Don’t Calculate Codabar Check Character Calculation = Enable AIM standard check char. Codabar Check Character Calculation = Enable Modulo 10 check char.
PAGE 230
Symbologies Codabar — cont. Codabar Check Character Transmission Enable this option to transmit the check character along with Codabar barcode data. ENTER/EXIT PROGRAMMING MODE Codabar Check Character Transmission = Don’t Send DEFAULT Codabar Check Character Transmission = Send Codabar Start/Stop Character Transmission Enable this option to enable/disable transmission of Codabar start and stop characters.
PAGE 231
Codabar Codabar — cont. Codabar Start/Stop Character Set This option specifies the format of transmitted Codabar start/stop characters.
PAGE 232
Symbologies Codabar — cont. Codabar Start/Stop Character Match When enabled, this option requires that start and stop characters match.
PAGE 233
Codabar Codabar — cont. Codabar Quiet Zones This feature specifies the number of quiet zones for Codabar labels. Quiet zones are blank areas at the ends of a barcode and are typically 10 times the width of the narrowest bar or space in the label.
PAGE 234
Symbologies Codabar — cont. Codabar Minimum Reads This feature specifies the minimum number of consecutive times a Codabar label must be decoded before it is accepted as good read..
PAGE 235
Codabar Codabar — cont. Codabar Decoding Level Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a very conservative decoder at the expense of not being able to read poorly printed or damaged labels. • Choosing Level 5 results in a very aggressive decoder.
PAGE 236
Symbologies Codabar — cont. Codabar Decoding Level — cont.
PAGE 237
Codabar Codabar — cont. Codabar Length Control This feature specifies either variable length decoding or fixed length decoding for the Codabar symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 238
Symbologies Codabar — cont. Codabar Set Length 1 This feature specifies one of the barcode lengths for Codabar Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s start, stop, check and data characters. The length must include at least one data character. The length can be set from 3 to 50 characters. Follow these instructions to set this feature: 1.
PAGE 239
Codabar Codabar — cont. Codabar Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Codabar Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 240
Symbologies Codabar — cont. Codabar Set Length 2 This feature specifies one of the barcode lengths for Codabar Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. The length includes the barcode’s start, stop, check and data characters. The length must include at least one data character. The length can be set from 3 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length).
PAGE 241
Codabar Codabar — cont. Codabar Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select CodabarLength 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 242
Symbologies Codabar — cont. Codabar Interdigit Ratio This feature specifies the ratio between an intercharacter space and module for Codabar labels.
PAGE 243
Codabar Codabar — cont. Codabar Interdigit Ratio — cont.
PAGE 244
Symbologies Codabar — cont. Codabar Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 245
Codabar Codabar Stitching This option enables/disables stitching for Codabar labels. When parts of a Codabar barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 246
Symbologies Code 11 The following options apply to the Code 11 symbology. Code 11 Enable/Disable When disabled, the reader will not read Code 11 barcodes.
PAGE 247
Code 11 Code 11 — cont. Code 11 Check Character Calculation This option enables/disables calculation and verification of optional Code 11 check character.
PAGE 248
Symbologies Code 11 — cont. Code 11 Check Character Transmission This feature enables/disables transmission of an optional Code 11 check character.
PAGE 249
Code 11 Code 11 — cont. Code 11 Minimum Reads This feature specifies the minimum number of consecutive times a Code 93 label must be decoded before it is accepted as good read..
PAGE 250
Symbologies Code 11 — cont. Code 11 Length Control This feature specifies either variable length decoding or fixed length decoding for the Code 11 symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 251
Code 11 Code 11 — cont. Code 11 Set Length 1 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. Follow these instructions to set this feature: 1. Determine the desired character length (from 2 to 50). Pad the number with leading zeroes to yield two digits.
PAGE 252
Symbologies Code 11 — cont. Code 11 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 11 Set Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 253
Code 11 Code 11 — cont. Code 11 Set Length 2 This feature specifies one of the barcode lengths for Code 11 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 2 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Follow these instructions to set this feature: 1.
PAGE 254
Symbologies Code 11 — cont. Code 11 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Code 11 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 255
Code 11 Code 11 — cont. Code 11 Interdigit Ratio This feature specifies the ratio between an intercharacter space and module for Code 11 labels.
PAGE 256
Symbologies Code 11 — cont. Code 11 Interdigit Ratio — cont.
PAGE 257
Code 11 Code 11 Decoding Level Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a very conservative decoder at the expense of not being able to read poorly printed or damaged labels. • Choosing Level 5 results in a very aggressive decoder.
PAGE 258
Symbologies Code 11 — cont. Code 11 Decoding Level — cont.
PAGE 259
Code 11 Code 11 — cont. Code 11 Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 260
Symbologies Code 11 Stitching This option enables/disables stitching for Code 11 labels. When parts of a Code 11 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 261
Standard 2 of 5 Standard 2 of 5 The following options apply to the Standard 2 of 5 symbology. Standard 2 of 5 Enable/Disable When disabled, the reader will not read Standard 2 of 5 barcodes.
PAGE 262
Symbologies Standard 2 of 5 — cont. Standard 2 of 5 Check Character Calculation This option enables/disables calculation and verification of an optional Standard 2 of 5 check character. ENTER/EXIT PROGRAMMING MODE DEFAULT Standard 2 of 5 Check Character Calculation = Disable Standard 2 of 5 Check Character Calculation = Enable Standard 2 of 5 Check Character Transmission This feature enables/disables transmission of an optional Standard 2 of 5 check character.
PAGE 263
Standard 2 of 5 Standard 2 of 5 — cont. Standard 2 of 5 Minimum Reads This feature specifies the minimum number of consecutive times a Standard 2 of 5 label must be decoded before it is accepted as good read.
PAGE 264
Symbologies Standard 2 of 5 — cont. Standard 2 of 5 Length Control This feature specifies either variable length decoding or fixed length decoding for the Standard 2 of 5 symbology. Variable Length — For variable length decoding, a minimum and maximum length may be set. Fixed Length — For fixed length decoding, two different lengths may be set.
PAGE 265
Standard 2 of 5 Standard 2 of 5 — cont. Standard 2 of 5 Set Length 1 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 1 is the minimum label length if in Variable Length Mode, or the first fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 1 to 50 characters. Follow these instructions to set this feature: 1. Determine the desired character length (from 1 to 50).
PAGE 266
Symbologies Standard 2 of 5 — cont. Standard 2 of 5 Set Length 1 — cont. ENTER/EXIT PROGRAMMING MODE Select Standard 2 of 5 Length 1 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 267
Standard 2 of 5 Standard 2 of 5 — cont. Standard 2 of 5 Set Length 2 This feature specifies one of the barcode lengths for Standard 2 of 5 Length Control. Length 2 is the maximum label length if in Variable Length Mode, or the second fixed length if in Fixed Length Mode. Length includes the barcode’s check and data characters. The length can be set from 1 to 50 characters. A setting of 0 specifies to ignore this length (only one fixed length). Follow these instructions to set this feature: 1.
PAGE 268
Symbologies Standard 2 of 5 — cont. Standard 2 of 5 Set Length 2 — cont. ENTER/EXIT PROGRAMMING MODE Select Standard 2 of 5 Length 2 Setting Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 269
Standard 2 of 5 Standard 2 of 5 — cont. Standard 2 of 5 Character Correlation When correlation is enabled, the barcode reader will combine label data from multiple scans when decoding. Enabling correlation will help the scanner read labels that have some spots and/or voids. It may also help read labels that have damaged areas. Enabling correlation will also increase the chances that a label will be read incorrectly.
PAGE 270
Symbologies Standard 2 of 5 Stitching This option enables/disables stitching for Standard 2 of 5 labels. When parts of a Standard 2 of 5 barcode are presented to the reader with this feature enabled, the barcode parts will be assembled by the reader’s software, and the data will be decoded if all barcode proofing requirements are met.
PAGE 271
ISBT 128 ISBT 128 The following options apply to the ISBT 128 symbology. ISBT 128 Enable/Disable When disabled, the imager will not read ISBT barcodes. ENTER/EXIT PROGRAMMING MODE DEFAULT ISBT 128 = Disable ISBT 128 = Enable ISBT 128 Concatenation Use this option to enable/disable ISBT128 concatenation of 2 labels.
PAGE 272
Symbologies ISBT 128 — cont. ISBT 128 Force Concatenation When enabled, this feature forces concatenation for ISBT. This option is only valid when ISBT 128 Concatenation is enabled. (see page 261). NOTE ENTER/EXIT PROGRAMMING MODE DEFAULT ISBT 128 Force Concatenation = Disable ISBT 128 Force Concatenation = Enable ISBT 128 Advanced Concatenation Options Contact Customer Support to set up pairs of label types for concatenation.
PAGE 273
Code 4 Code 4 The following options apply to the Code 4 symbology. Code 4 Enable/Disable Enables/Disables ability of imager to decode Code 4 labels.
PAGE 274
Symbologies Code 4 — cont. Code 4 Check Character Transmission This feature enables/disables transmission of an optional Code 4 check character. ENTER/EXIT PROGRAMMING MODE Code 4 Check Character Transmission = Don’t Send DEFAULT Code 4 Check Character Transmission = Send Code 4 Hex to Decimal Conversion This feature enables/disables the conversion of hexidecimal label data to decimal label data.
PAGE 275
Code 5 Code 5 The following options apply to the Code 5 symbology. Code 5 Enable/Disable Enables/Disables ability of imager to decode Code 5 labels.
PAGE 276
Symbologies Code 5 — cont. Code 5 Check Character Transmission This feature enables/disables transmission of an optional Code 5 check character. ENTER/EXIT PROGRAMMING MODE Code 5 Check Character Transmission = Don’t Send DEFAULT Code 5 Check Character Transmission = Send Code 5 Hex to Decimal Conversion This feature enables/disables the conversion of hexidecimal label data to decimal label data.
PAGE 277
Code 4 and Code 5 Common Configuration Items Code 4 and Code 5 Common Configuration Items The following options apply to both Code 4 and Code 5 symbologies. Code 4 and 5 Decoding Level Decoding Levels are used to configure a barcode symbology decoder to be very aggressive to very conservative depending on a particular customer’s needs. • Choosing Level 1 results in a very conservative decoder at the expense of not being able to read poorly printed or damaged labels.
PAGE 278
Symbologies Code 4 and Code 5 Common Configuration Items — cont. Code 4 and 5 Decoding Level — cont.
PAGE 279
Code 4 and Code 5 Common Configuration Items Code 4 and Code 5 Common Configuration Items — cont. Code 4 and Code 5 Minimum Reads This feature specifies the minimum number of consecutive times a Code 4 or Code 5 label must be decoded before it is accepted as good read.
PAGE 280
Symbologies Follett 2 of 5 The following options apply to the Follett 2 of 5 symbology. Follett 2 of 5 Enable/Disable Enables/Disables ability of imager to decode Follett 2 of 5 labels.
PAGE 281
Follett 2 of 5 NOTES Product Reference Guide 271
PAGE 282
Symbologies 272 PowerScan® PBT7100 Cordless
PAGE 283
Chapter 12 BT Features Introduction This section provides options and programming related to the reader’s radio communication features. Standard Factory Settings Reference Appendix B, Standard Defaults for a listing of standard factory settings.
PAGE 284
BT Features BT Beeper Features Several options are available to configure beeper behavior for BT operation. ACK Beep Enables/disables the ACK beep indication. The ACK beep occurs in reponse to the label acknowledgement (HACK) from the Base Station. The HACK signal is sent according to the settings made for BT Address Stamping on page 296.
PAGE 285
BT Beeper Features Beep Frequency Adjusts radio-specific beep indications to sound at a low, medium or high frequency, selectable from the list below. (Controls the beeper’s pitch/tone.
PAGE 286
BT Features Beep Duration This feature controls the duration of radio-specific beep indications.
PAGE 287
BT Beeper Features Beep Duration — cont.
PAGE 288
BT Features Beep Volume Selects the beeper volume (loudness) of radio-specific beep indications. There are three selectable volume levels.
PAGE 289
BT Beeper Features BT Base Station Beep Enables/disables a beep indication when the handheld is placed in the Base Station. ENTER/EXIT PROGRAMMING MODE BT Base Station Beep = Disable DEFAULT BT Base Station Beep = Enable Disconnect Beep Enables/disables the beep indication that a handheld has become disconnected from a Base Station.
PAGE 290
BT Features BT Leash Alarm This setting specifies the number of seconds to sound the Leash Mode beeps (three per second) when the handheld goes out of range. This is especially useful in instances where the reader might inadvertently have been placed in a bag or cart. For this mode to be effective, the feature Sleep Mode Timeout on page 21, must be disabled.
PAGE 291
BT Beeper Features BT Leash Alarm — cont.
PAGE 292
BT Features Flash Update BT Automatic Flash Update This feature enables/disables the automatic flash update of a reader. ENTER/EXIT PROGRAMMING MODE DEFAULT BT Automatic Flash Update = Disable BT Automatic Flash Update = Enable Request Flash Update Scan this barcode to request a flash update from a Base Station Do not scan an ENTER/EXIT PROGRAMMING MODE label in conjunction with this barcode.
PAGE 293
Configuration Update Configuration Update Automatic Configuration Update When this feature is enabled, a reader and its linked Base Station can automatically ensure they stay in sync with regard to application hardware and/or configuration. This is accomplished by the linked reader and Base Station comparing application version number and configuration file check sum. If either is different, the Base Station will automatically update the reader with its application/configuration.
PAGE 294
BT Features Configuration Update — cont. Copy Configuration From Handheld to Base Station Use this barcode to manually copy the handheld configuration to the Base Station. Do not scan an ENTER/EXIT PROGRAMMING MODE label in conjunction with this barcode.
PAGE 295
Battery Charge Mode Battery Charge Mode This feature specifies the battery charge mode for the Base Station.
PAGE 296
BT Features Powerdown Timeout The Powerdown Timeout feature sets the time for automatically switching the unit off when the imager has been idle.
PAGE 297
Powerdown Timeout Powerdown Timeout — continued ENTER/EXIT PROGRAMMING MODE DEFAULT Powerdown Timeout = 60 Minutes Powerdown Timeout = 90 Minutes Powerdown Timeout = 120 Minutes Product Reference Guide 287
PAGE 298
BT Features BT Poll Rate This feature Specifies the time between BT polls.
PAGE 299
BT Poll Rate BT Poll Rate — cont.
PAGE 300
BT Features Batch Features Batch Mode This option specifies which mode to use to store labels in the handheld while disconnected from the base. Options are as follows: • Disabled — The handheld will not store/batch labels. • Automatic — The handheld will store labels to RAM when the handheld goes out of range and is disconnected from the remote device. • Manual — The handheld will always store labels to Flash memory.
PAGE 301
BT Security Features Batch Features — cont. Send Batch Use this barcode to initiate sending of labels stored in batch memory. Do not scan an ENTER/EXIT PROGRAMMING MODE label in conjunction with this barcode. NOTE Send Batch Erase Batch Memory Use this barcode to erase any labels stored in batch memory. Do not scan an ENTER/EXIT PROGRAMMING MODE label in conjunction with this barcode.
PAGE 302
BT Features 3. Scan the ENTER/EXIT PROGRAMMING MODE barcode to enter Programming Mode. 4. Scan the barcode: SELECT BT PIN CODE. 5. Scan the appropriate alpha-numeric characters from the keypad in Appendix E, Keypad representing the hexidecimal entries which was determined in the steps above. You will hear a two-beep indication after the last character. If you make a mistake before the last character, scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 303
BT Security Features BT Pin Code — cont. ENTER/EXIT PROGRAMMING MODE Select BT Pin Code Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 304
BT Features BT Security Mode This feature enables/disables authentication and encryption of the BT link. Use the feature, BT Pin Code on page 291, to specify the pin code used to authenticate the BT Link. Changing the security mode setting will unlink the devices. The setting must also be changed on the Base Station using Aladdin, then the Base Station and reader must be relinked.
PAGE 305
BT SPP Mode BT SPP Mode Enables/disables the ability of the Base Station to emulate a PowerScan 7000 model Base Station. When enabled, the Base Station can link with a PowerScan 7000BT handheld. To use this feature, BT Security Mode on page 294 must be disabled.
PAGE 306
BT Features BT Address Stamping These features allow configuration of source radio data inclusion. Source Radio Address Transmission Enables/disables the ability of source radio information to be transmitted to the host and, if so, at what position with respect to the label data. Options are: Do Not Include — Do not include source-radio ID Prefix — Include source-radio ID as prefix When included as a prefix, the source-radio ID is displayed after all label formatting has been applied.
PAGE 307
BT Address Stamping Source Radio Address Delimiter Character This option specifies the delimiter character to be placed between the label data and radio address when address stamping is enabled. This feature only applies if Source Radio Address Transmission on page 296 is enabled. NOTE Follow these instructions to select the delimiter character: 1. Determine the desired character, then find its hexadecimal equivalent on the ASCII Chart on the inside back cover.
PAGE 308
BT Features Source Radio Address Delimiter Character — cont. ENTER/EXIT PROGRAMMING MODE Set Source Radio Address Delimiter Character Make a mistake? Scan the CANCEL barcode to abort and not save the entry string. You can then start again at the beginning.
PAGE 309
Appendix A Technical Specifications Table 37 contains Physical and Performance Characteristics, User Environment and Regulatory information. Table 38 provides Standard Cable Pinouts. Table 37. Technical Specifications Item Description Physical Characteristics — Reader Color Yellow/Black Black/Black Dimensions Height 7.5”/190 mm Length 4.5”/115 mm Width 3.0”/75 mm Weight (battery included) Approximately 13.
PAGE 310
Item Description Roll (Tilt) Tolerance ± 30° from normal Pitch Tolerance ± 82° Skew (Yaw) Tolerance ± 65° Field of View 2” wide at 1” from the reader 7” wide at 7” from the reader Depth of Field 100 mil: typical 5.1" to 208.7" (13 cm to 530 cm) 55 mil: typical 1.9" to 118.1" (4.7 cm to 300 cm) 40 mil: typical 0.8" to 94.5" (2 cm to 240 cm) 20 mil: typical 0.1" to 46.9" (0.3 cm to 119 cm) 13 mil: typical 0" to 31.5" (0.1 cm to 80 cm) 10 mil: typical 0" to 23.6" (0 cm to 60 cm) 7.5 mil: typical 0.
PAGE 311
Item ESD Level Description 25 KV User Environment — Base Station & Charger Contaminants Spray/rain Dust/particulates IEC 529-IPX4 IEC 529-IP5X Regulatory Electrical Safety UL 60950-1, CSA C22.2 No. 60950-1, IEC 60950-1 EMI/RFI USA FCC Part 15 Class B. Canada ICES-003 Class B. European Union EMC and R&TTE Directives. EN 301 489-17 — Radio Immunity. EN 300 328 v 1.7.1 Radio Emissions. EN 61000 6-2 — Generic Immunity for Industrial Environments. EN 50392 — Human exposure to electromagnetic fields.
PAGE 312
Standard Cable Pinouts Figure 8 and Table 38 provide standard pinout information for the Base Station’s cable. Figure 8. Standard Cable Pinouts Bottom of Base Station Cable Cable Strain Relief To Host Interface Cable Port (in Base cavity) Pin 1 Pin 10 Cable Clip (Latch) The signal descriptions in Table 38 apply to the connector on the Base Station and are for reference only. Table 38.
PAGE 313
Appendix B Standard Defaults The most common configuration settings are listed in the “Default” column of the table below. Page references are also provided for feature descriptions and programming barcodes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 39. Standard Defaults Parameter Default Your Setting Page Number General Features Double Read Timeout 0.
PAGE 314
Parameter Green Spot Duration Default Your Setting Page Number 300 ms 45 9600 47 Data Bits 8 Data Bits 49 Stop Bits 1 Stop Bit 50 None 51 Disable 52 No Delay 52 Beep On ASCII BEL Disable 56 Beep On Not on File Enable 56 ACK Character ‘ACK’ 58 NAK Character ‘NAK’ 60 600 ms 62 3 Retries 64 Ignore Errors Detected 66 Enable 67 Disable Character ‘D’ 68 Enable Character ‘E’ 70 Country Mode U.S.
PAGE 315
Parameter USB Keyboard Speed Default Your Setting Page Number 1 ms 85 Handheld Reader 88 No Global Prefix Global Suffix = 0x0D (CR) 96 Global AIM ID Disable 98 Label ID Control Disable 105 Case Conversion Disable 112 No Char Conversion 113 Enable UPC/EAN coupon decoding 116 UPC-A Enable/Disable Enable 117 UPC-A Check Character Transmission Enable 117 Don’t Expand 118 Transmit 118 UPC-A Minimum Reads 1 136 In-Store Minimum Reads 2 119 Enable 120 Send 120 Expand UPC
PAGE 316
Parameter Default Your Setting Page Number EAN 13 EAN 13 Enable/Disable Enable 125 Send 125 EAN-13 Flag 1 Character Transmit 126 EAN-13 ISBN Conversion Disable 127 EAN 13 Minimum Reads 1 128 Enable 129 Send 129 Disable 130 1 131 3 132 UPC/EAN Correlation Disable 134 UPC/EAN Reconstruction Disable 134 UPC/EAN Price Weight Check Disable 135 Disable P2, P5 and P8 137 Optional Add-On Timer 70 ms 139 Optional GS1-128 Add-On Timer Disable 142 P2 Add-Ons Minimum Reads
PAGE 317
Parameter Default Your Setting Page Number DataBar Expanded GS1 DataBar Expanded Enable/Disable Disable 150 GS1 DataBar Expanded GS1-128 Emulation Disable 150 GS1 DataBar Expanded Minimum Reads 1 151 GS1 DataBar Expanded Length Control Variable 152 GS1 DataBar Expanded Set Length 1 1 153 GS1 DataBar Expanded Set Length 2 74 155 GS1 DataBar Limited Enable/Disable Disable 157 GS1 DataBar Limited GS1-128 Emulation Disable 157 1 158 Enable 159 Calculate 160 Code 39 Check Charac
PAGE 318
Parameter Code 32 Feature Setting Exceptions Default Your Setting Page Number 3 176 Code 32 Check Character Transmission Don’t Send 177 Code 32 Start/Stop Character Transmission Don’t Transmit 177 Enable 178 Don’t Expand 178 Code 128 Check Character Transmission Send 179 Code 128 Quiet Zones Auto 181 Code 128 Minimum Reads 1 182 Code 128 Decoding Level 3 183 Code 128 Length Control Variable 185 Code 128 Set Length 1 1 186 Code 128 Set Length 2 80 188 Code 128 Character
PAGE 319
Parameter I 2 of 5 Length Control Default Your Setting Page Number Variable 199 I 2 of 5 Set Length 1 12 200 I 2 of 5 Set Length 2 100 202 I 2 of 5 Character Correlation Disable 204 I 2 of 5 Stitching Disable 205 Datalogic 2 of 5 Enable/Disable Enable 206 Datalogic 2 of 5 Check Character Calculation Disable 207 Datalogic 2 of 5 Minimum Reads 1 208 Datalogic 2 of 5 Length Control Variable 209 Datalogic 2 of 5 Set Length 1 12 210 Datalogic 2 of 5 Set Length 2 100 212 Datal
PAGE 320
Parameter Default Your Setting Page Number Codabar Character Correlation Disable 234 Codabar Stitching Disable 235 Disable 236 Check C and K 237 Send 238 Code 11 Minimum Reads 1 239 Code 11 Length Control Variable 240 Code 11 Set Length 1 4 241 Code 11 Set Length 2 50 243 Code 11 Interdigit Ratio 4 245 Code 11 Decoding Level 3 247 Code 11 Character Correlation Disable 249 Code 11 Stitching Disable 250 Standard 2 of 5 Enable/Disable Disable 251 Standard 2 of 5 Check
PAGE 321
Parameter Default Your Setting Page Number Code 4 Code 4 Enable/Disable Code 4 Check Character Transmission Code 4 Hex to Decimal Conversion Disable 263 Don’t Send 264 Enable 264 Disable 265 Send 266 Enable 266 Code 5 Code 5 Enable/Disable Code 5 Check Character Transmission Code 5 Hex to Decimal Conversion Code 4 and Code 5 Common Configuration Items Code 4 and 5 Decoding Level 3 267 Code 4 and Code 5 Minimum Reads 1 269 Disable 270 Enable 274 Low 275 Beep Duration 80 ms 276
PAGE 322
Parameter BT Pin Code Your Setting Page Number 1234 291 BT Security Mode Disable 294 BT SPP Mode Disable 295 Send HACK as soon as the Base Station receives a label 296 Do Not Include 296 No Delimiter Character 297 BT Address Stamping Source Radio Address Transmission Source Radio Address Delimiter Character 312 Default PowerScan® PBT7100 Cordless
PAGE 323
Appendix C LED and Beeper Indications The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The tables below list these indications. One exception to the behaviors listed in the tables is that the reader’s functions are programmable, and may or may not be turned on. For example, certain indications, such as the power-up beep can be disabled using programming barcode labels.
PAGE 324
General Functions — LED and Beeper Indications INDICATION DESCRIPTION Power-up Beep The reader is in the process of powering-up. Good Read Beep A label has been successfully scanned by the reader. ROM Failure There is an error in the reader's software/programming Limited Scanning Label Read LED BEEPER Reader beeps four times at highest frequency and volume upon powerup.
PAGE 325
BT Beeper Indications BT Beeper Indications Beep Type Description Behavior Acknowledge (ACK) Label A label has been sent to the Base Station, which has accepted the data and responded. Control via ACK NAK Options on page 57. 1 beep. Duration, frequency and volume vary, since these are all configurable for this feature. Label Rejected Label data sent is rejected by the Base Station (responds with NAK). Control via ACK NAK Options on page 57. 2 beeps at low frequency.
PAGE 326
BT LED Indications Applies to: LED Indication Linking in progress Behavior Yellow LED blinks at 2 Hz Base Station Reader YES YES NO YES Green LED blinks 10 times after either of the following events occur: -After every 10th trigger pull. Low battery -After 30 seconds of idle time. NOTE: Low battery LED indication coincides with the low battery beep. Disconnected LEDs off YES YES Unlinked LEDs off YES YES BT transmission in progress Flash yellow LED at 50 Hz while transmitting.
PAGE 327
Error Codes Error Codes Upon startup, if the reader sounds a long tone, this means the reader has not passed its automatic Selftest and has entered FRU1 isolation mode. If the reader is reset, the sequence will be repeated. The following table describes the LED flashes/beep codes associated with an error found.
PAGE 328
NOTES 318 PowerScan® PBT7100 Cordless
PAGE 329
Appendix D Sample Barcodes The sample barcodes in this appendix are typical representations for their symbology types.
PAGE 330
Sample Barcodes — continued Code 32 00246897634 Codabar 5765485 Code 93 Code 11 7554628485 MSI 74759330108 320 PowerScan® PBT7100 Cordless
PAGE 331
DataBar (RSS) DataBar (RSS) DataBar variants must be enabled to read the barcodes below (see DataBar (RSS) on page 321).
PAGE 332
NOTES 322 PowerScan® PBT7100 Cordless
PAGE 333
Appendix E Keypad Use the barcodes in this appendix to enter numbers as you would select digits/characters from a keypad.
PAGE 334
6 7 8 9 A B C 324 PowerScan® PBT7100 Cordless
PAGE 335
D E F Product Reference Guide 325
PAGE 336
NOTES 326 PowerScan® PBT7100 Cordless
PAGE 337
Appendix F Scancode Tables Control Character Emulation Control character emulation selects from different scancode tables as listed in this appendix. Each of the control character sets below are detailed by interface type in the tables. These apply to Wedge and USB Keyboard platforms. Control Character 00 . Characters from 00 to 0x1F are sent as control character Ctrl+Keys, special keys are located from 0x80 to 0xA1. Control Character 01 .
PAGE 338
Product Reference Guide Extended characters (sky blue) are sent through dedicated keys (when available in the selected country mode) or by using an Alt Mode sequence. Table F-1.
PAGE 339
Product Reference Guide Table F-2. Scancode Set When Control Character is 02 Interface Type PC AT PS/2 or USB-Keyboard — cont.
PAGE 340
Product Reference Guide Table F-3.
PAGE 341
Product Reference Guide Table F-4. Scancode Set When Control Character is 02 Interface type PC AT PS/2 Alt Mode or USB-Keyboard Alt Mode — cont.
PAGE 342
Product Reference Guide Table F-5.
PAGE 343
Product Reference Guide Table F-6. Scancode Set When Control Character is 02 Digital Interface — cont.
PAGE 344
Product Reference Guide Table F-7.
PAGE 345
Product Reference Guide Table F-8. Scancode Set When Control Character is 02 IBM31xx 102-key — cont.
PAGE 346
Product Reference Guide Table F-9.
PAGE 347
Product Reference Guide Table F-10. Scancode Set When Control Character is 02 IBM XT — cont.
PAGE 348
Microsoft Windows Codepage 1252 Windows-1252 is a character encoding of the Latin alphabet, used by default in the legacy components of Microsoft Windows in English and some other Western languages.
PAGE 349
Index A E Ambient Light Immunity 300 Electrical Safety 301 EMI/RFI 301 Error Codes 317 Errors 317 B bar codes RS-232 baud rate 85 RS-232 parameters parity 261, 263, 265, 268, 270 barcodes cancel 323 numeric barcodes 323 RS-232 parameters parity 76 Beeper Pitch, Good Read 25, 26 Volume, Good Read 28 Beeper Volume 300 Beeper, Good Read 23 C G Good Read, Beeper Pitch 25, 26 Volume 28 Good Read, Beeper Good Read, Beeper Good Read, Beeper Green Spot 313 – 23 Pitch – 25, 26 Volume – 28 H Handheld Scanner
PAGE 350
M symbology types 319 Mixed OEM Standard + Code 39 Format 93 T N Table Top Scanner 88 numbers lock key 77 U O UPC 117 USB interface selection 12 User Environment 300, 301 Operating Temperature 300 P Performance Characteristics 299 Physical Characteristics 299 Pitch – Good Read, Beeper 25, 26 Pitch Tolerance 300 Prefix/Suffix 96 Print Contrast Minimum 300 Product Specifications 299 Programming Barcodes 9 V Volume – Good Read, Beeper 28 W Weight 299 X XON/XOFF 52 R Read, Beeper – Good 23 Read,
PAGE 351
ASCII Chart ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. NUL SOH STX ETX EOT ENQ ACK BEL BS HT LF VT FF CR SO SI DLE DC1 DC2 DC3 DC4 NAK SYN ETB CAN EM SUB ESC FS GS RS US 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F SP ! “ # $ % & ’ ( ) * + , .
PAGE 352
Australia Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Japan Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Datalogic Scanning Sarl Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Latin America Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.