PowerScanTM PBT7100 Cordless Imaging Reader Quick Reference Guide
Datalogic ADC, Inc. 959 Terry Street Eugene, OR 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 ©2008 - 2013 Datalogic, Inc. An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic ADC, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic ADC”).
Table of Contents Statement of Agency Compliance ............................................. 3 FCC Class B Compliance Statement ....................................................... 3 Canadian Notice ....................................................................................... 3 Solids and Water Protection ................................................................... 3 Laser Cautions ..........................................................................................
NOTES 2 TM PowerScan PBT7100 Cordless Imaging Reader
Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Class B Compliance Statement The user is cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user’s authority to operate the equipment.
Laser Cautions The imager may contain a laser pointer (this is a value-added option), which is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC 60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous.
2.2 Datalogic has obtained a licensed right. As used in this Agreement, the term “purchase” or its equivalents when applied to the Software shall mean “acquire under license.” End User is not entitled to receipt or use of the source code to any Software.
CLAIMS OF PATENT, COPYRIGHT, OR OTHER INTELLECTUAL PROPERTY INFRINGEMENT, CANCELS AND SUPERCEDES ANY PRIOR AGREEMENTS, WHETHER ORAL OR WRITTEN, BETWEEN THE PARTIES CONCERNING SUCH CLAIMS, AND WILL NOT BE MODIFIED OR AMENDED BY ANY PAST, CONTEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES. 8. Limitation Of Liability.
Getting Started Installing the Battery Pack To charge the Battery Pack, See “Battery Pack Charging and Maintenance” on page 11. NOTE WARNING Datalogic recommends annual replacement of rechargeable battery packs to ensure maximum performance. Do not discharge the battery using any device except for the reader. When the battery is used in devices other than the linear imager, it may damage the battery or reduce its life expectancy.
Always charge the battery at 32° – 113°F (0° - 45°C) temperature range. CAUTION Use only the authorized power supplies, battery pack, chargers, and docks supplied by your Datalogic reseller. The use of any other power supplies can damage the linear imager and void your warranty. Do not disassemble or modify the battery. The battery contains safety and protection devices, which, if damaged, may cause the battery to generate heat, explode or ignite.
Getting Started Figure 1-1. Battery Pack Installation & Removal Scanner Alignment Pins Battery Pack Release Latch Release Latch Verifying Reader Operation Before Linking Once a charged Battery Pack has been installed in the reader, scan a good sample barcode of the symbology1 type your reader is programmed to read. If unsure how to do this, see the section on How to Scan in this manual. Tip: The part number barcode on the back cover of this manual is a Code 39 symbology sample.
Figure 1-2. Labeling and Nomenclature This illustration shows label placement ONLY. For actual regulatory, patent and other applicable information, view the labels on the product intself, or call your nearest sales or service office.
Getting Started Linking the Reader to a Base Station To link the reader to its own Base Station, refer to the instructions provided in the Base Station Quick Reference Guide (QRG). NOTE Linking the Reader to a Bluetooth® Enabled Device A reader can optionally be linked to a PC with a Bluetooth radio installed. 1. Ensure that the Bluetooth enabled device and its driver are installed on the PC. 2. On the PC, open the control window for the Bluetooth device (usually called “My Bluetooth Places”).
There presently are no US, North America or World disposal requirements for Lithium-Ion batteries such as the Battery Pack, so when they won't hold a charge anymore they can be disposed of; preferably through a recycling center. Contact your local government for disposal or recycling practices in your area. Figure 1-3. Charging the Battery Pack in a Docked Reader Programming The reader is typically factory-configured with a set of default features.
Defaults Defaults For your convenience, standard factory defaults 1are shown here for each of the major interface types. For more details or to change these settings, reference the Product Reference Guide (PRG).
How to Scan When the trigger is pressed, a red laser aiming beam is activated, enabling the user to align its horizontal and vertical position with the desired barcode. The aiming beam will remain on until a configurable time-out1 period elapses, then the red scan LEDs are activated to read the barcode. If the barcode is not decoded before another configurable period has expired, the laser aiming beam will begin blinking to allow the user to continue pointing the reader at the desired barcode.
Troubleshooting • the battery is charged. See Battery Pack Charging and Maintenance on page 11. • the battery is properly installed. See Installing the Battery Pack on page 7. • the reader is linked to the desired Base Station. See the Quick Reference Guide (QRG) for the Base Station. • the reader is within reasonable operating range of the Base Station, with no major obstructions between the radio units such as thick walls or heavy machinery.
• The reader may not be programmed to output your barcode data properly. For example, you scan “12345” and the host displays “A12345B.” Reprogram the reader with the proper Data Editing selections. Reference the PRG. • The reader won’t read your barcode at all. • Scan the part number barcode on the back of this manual or other known-good barcode samples. If the reader reads sample barcodes, check that your target barcode is readable. • Verify that your barcode symbology is enabled. See the PRG.
Troubleshooting units and at its sole discretion can return the units in the “factory default” configuration or with any software or firmware update available at the time of the repair (other than the firmware or software installed during the manufacture of the product). Customer accepts responsibility to maintain a back up copy of its software and data.
(vi) any damage or malfunctioning caused by non-restoring action as for example firmware or software upgrades, software or hardware reconfigurations etc.; (vii) the replacement of upper window/cartridge due to scratching, stains or other degradation and/or (viii) any consumable or equivalent (e.g., cables, power supply, batteries, keypads, touch screen, triggers etc.).
Troubleshooting WEEE Statement Waste Electrical and Electronic Equipment (WEEE) Statement. English For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.datalogic.com. Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.datalogic.com. French Pour toute information relative à l’élimination des déchets électroniques (WEEE), veuillez consulter le site internet www.
China RoHS 20 PowerScan PBT7100TM Cordless Imaging Reader
DECLARATION OF CONFORMITY 13 EC-094 Rev.:1 Pag.: 1 di 1 Datalogic ADC, Inc. 959 Terry Street Eugene, Oregon 97402 USA La presente dichiarazione di conformità è rilasciata sotto la responsabilità esclusiva di Datalogic ADC, Inc. per: This Declaration of Conformity is issued under the sole responsibility of Datalogic ADC, Inc.
www.datalogic.com ©[2008-2013] Datalogic, Inc. All rights reserved. Datalogic and the Datalogic logo are registered trademarks of Datalogic S.p.A. in many countries, including the U.S.A. and the E.U. Datalogic ADC, Inc. 959 Terry Street | Eugene |OR 97402 | USA Telephone: (1) 541-683-5700 | Fax: (1) 541-345-7140 820029414 (Rev.
