MagellanTM 8300/8400 Quick Reference Guide
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
DATALOGIC SCANNING, INC. MAGELLANTM END USER LICENSE AGREEMENT Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement.
6.2 uninterrupted or error free, or that Datalogic's remedial efforts will correct any nonconformance. This limited warranty does not cover any product that has been subjected to damage or abuse, whether intentionally, accidentally, or by neglect, or to unauthorized repair or unauthorized installation, and shall be void if End User modifies the product, uses the product in any manner other than as established in the Documentation, or if End User breaches any of the provisions of this Agreement.
Quick Reference The object of this manual is to provide general operational information for the user. For more product details, including installation, set-up, programming and advanced user information, reference the Product Reference Guide (PRG), which is available for viewing and download from the website listed on the back cover of this manual. Controls and Indicators The control panel consists of an indicator LED and two push buttons as shown in Figure 1.
Power Supply The scanner may require either a Listed Class 2 or Listed LPS power source which supplies power directly to the unit. It is sometimes possible for a scanner to receive power directly from the terminal (P.O.T.). See the current product data sheet for more information about P.O.T. Scanning Items Push or slide items through the 360° scan zone (shown here) in either a left-toright or right-to-left motion.
With the 360° scan pattern and advanced FirstStrike® decoding software, the Magellan® 8300/8400 can read most hard-to-read codes quickly and without excess orientation. Weighing Items Using the All-Weighs® Platter Items to be weighed can be placed anywhere on the L-shaped All-Weighs® platter (weigh platter) surface. Oversized items can even be accurately weighed while leaned against the center of its vertical section as shown.
Table 1.
Volume/Tone Push Button The Volume/Tone Push Button also performs multiple functions depending upon the duration of time it is pressed: Table 2. Volume/Tone Push Button Functions PRESS DURATION FUNCTION COMMENT Wakes scanner from Sleep Mode Alternatively, the scanner can be awakened by: - Moving an object through the scan zone. - A weight change on the scale. - Scanning with an attached auxiliary scanner. Increments volume Press the push button momentarily to increase speaker volume.
Scale Zero Push Button The Scale Zero Push Button is used for two functions as described in Table 3. This button has no function on “scanner-only” models. Table 3. Scale Zero Push Button Functions PRESS DURATION FUNCTION COMMENT Momentary Zero Scale When programmed to do so, the yellow Scale LED should be lit when no weight is on the scale, indicating scale at zero. If it is not, press the switch to zero the scale. The unit will sound a “click” upon pressing the button.
Product Labeling The location of scanner and scanner/scale labeling is shown in Figure 4. Figure 4. Labeling Product Family Label Labels are IEC Laser Warning Model/Serial Number located under the platter, inside the unit and on its Bottom Cover. Scale Regulatory I/F Connector ID and Regulatory Labels are shown here to illustrate their general location only. Please view the labels on your product for actual details. NOTE Compliance Statement This device complies with Part 15 rules.
Adaptive Scale Platter Option Some Platters have been shipped with installed spacers on their undersides at all four corners. These specially-configured Platters are provided for customers wishing to add an adaptive scale to their unit at a later date. Until such time as the adaptive scale is installed, the four spacers should be left in place to ensure that the Platter rests evenly at its correct height when positioned on the scanner.
Appendix A — Warranty Warranty Datalogic warrants to Customer that this product will be free from defects in materials and workmanship for a period of 1 year from product shipment. In order to obtain service under this Warranty, Customer must notify Datalogic of the claimed defect before the expiration of the Warranty period and obtain from Datalogic a return authorization number for return of the product to designated Datalogic service center.
such loss or damage as may be caused by the negligence of Customer, its agents or employees. In the absence of specific written instructions for the return of product to Customer, Datalogic will select the carrier, but Datalogic shall not thereby assume any liability in connection with the return shipment.
EC DECLARATION OF CONFORMITY Non-Automatic Weighing Instrument Datalogic hereby declares that the equipment specified below and as referenced in the EC Type Approval Certificate has been tested and found compliant to the following European Council Directives and Harmonized Standards: Equipment Type: Barcode Scanning and Weighing Equipment Class Apparatus 830x / 840x, 830xb/840xb EC Type Approval Certificate: T7276 Year in which "CE"marking affixed: 09 Manufactured by: Datalogic Scanning, Inc. 959 Terry St.
Australia Japan Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Latin America Datalogic Scanning SAS Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Singapore Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.
