MagellanTM 8300/8400 Technical Guide
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 USA Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
Product Reference Guide 3
Table of Contents Chapter 1. Introduction ................................................................................... 1-1 Technical Support ........................................................................................................ Datalogic Website Support ...................................................................................... Reseller Technical Support ...................................................................................... Telephone Technical Support ....
Scale Error Reporting ................................................................................................... 3-6 Chapter 4. Calibration ...................................................................................... 4-1 Description of Calibration Sequence ................................................................................ 4-2 Motion Test .................................................................................................................
Chapter 1 Introduction Technical Support Datalogic Website Support The Datalogic website (www.scanning.datalogic.com) is the complete source for technical support and information for Datalogic products. The site offers product support, product registration, warranty information, product manuals, product tech notes, software updates, demos, and instructions for returning products for repair.
Scanner and Scanner/Scale Nomenclature Controls, indicators and other nomenclature are shown in Figure 1-1. Figure 1-1.
Connections Connections Two connector panels are located on either side of the scanner as shown in Figure 1-2. The appearance of these panels will vary depending upon the factory options purchased with your model. Additionally, a service “pigtail” extends from the scanner’s base to connect the control panel cable from the Bonnet area. Figure 1-2. Connectors Control Panel Service Loop Scanner Right Profile Scanner Left Profile 0.00 EAS Port EAS PORT Aux.
Weighing Specifications for scale capacity, settling time, minimum and maximum static weight, zeroing, and warm-up time are given below. Rated Weight Capacity The scale’s operational weight capacity is: • 15.000 kilograms, displayed in 0.005 increments. Minimum Increment The minimum weight that can be accurately measured by the scale is 0.005 kg. Maximum Static Weight (Overload) A maximum static weight of 68 kg can be sustained by the scale without incurring damage or degrading performance.
Weighing Warm-Up Time There are two pertinent warm-up times that apply to the scanner or scanner/scale: The two warm-up periods can be performed concurrently, thereby reducing the total required warm-up time to 60 minutes. NOTE Thermal Equilibrium When the unit is moved from a cooler temperature (such as a storage area) to a warmer environment (such as a checkstand location), 60 minutes must be allowed to acclimate the unit to ambient conditions prior to calibration or operation.
Figure 1-3.
Electrical Specifications Power Supply Power Off the Terminal (P.O.T) Certain units can receive power directly from the terminal (P.O.T.). A USB adapter “brick” connects the scanner to IBM-USB 12V ports. Power supplied from the terminal does not include auxiliary power for alternative scales. NOTE AC Adapter Units which do not receive power directly from the terminal will use either a Listed Class 2 or Listed LPS power source which supplies power directly to the unit.
Agency Compliances The scanner and scanner/scale meets or exceeds the requirements for its device type as set forth by the following agencies and regulations: COUNTRY COMPLIANCE COMMENTS Electrical United States UL 60950 State of California Energy Efficiency Standard Canada CAN/CSA 60950 Europe TÜV EN 60950 Mexico NOM Korea K-Mark Argentina IRAM Taiwan BSMI China CCC Japan PSE Australia/New Zealand AS/NZ 60950 Emisions United States 47CFR Part 15J FCC Class B Canada ICES-0003
Agency Compliances COUNTRY ROW COMPLIANCE CISPR 22 COMMENTS Class B Laser Safety United States CDRH, 21CFR Part 1040 CDRH Class IIa laser device Europe IEC60825-1:2007 EN60825-1:2007 Class 1 Class 1 Weights & Measures United States NIST Handbook 44 Canada Measurement Canada Australia/New Zealand National Measurement Institute Brazil INMETRO EC Countries Type Approval Cert Mexico NOM Puerto Rico Same as USA Singapore Spring Singapore ROW OIML R76 (Dept.
NOTES 1-10 Magellan® 8300/8400
Chapter 2 Site Preparation and Installation Models Scanner and scanner/scale models (reference Figure 2-1) are available in different lengths, allowing them to fit with little or no modification into openings cut for previously installed scanners such as Datalogic® Magellan® scanners, or NCR® scanner models 7820/24 and 7870. Other models are designed for applications with smaller footprint requirements. Figure 2-1 provides simplified illustrations of short, medium and long models.
Figure 2-1. Model Examples Scanner ONLY models Scanner/Scale models Model 8301/8401 Short Model 8304/8404 Model 8302/8402 Medium Medium Model 8305/8405 Model 8303/8403 Long Long Figure 2-2. Flanged and Shelf Model Examples Flange Model Shelf Model Flanges Figure 2-3.
Pre-Installation Considerations Pre-Installation Considerations It should be noted that the scope of this manual does not encompass all factors related to worker safety and checkstand design. It does, however, offer a list of considerations that may be helpful in ensuring greater safety and productivity. Careful planning using these general guidelines should result in a more efficient, comfortable work environment. The U.S.
5. Select a design which encourages the cashier to slide products across the scanner rather than gripping and lifting. Make sure the horizontal surface of the scanner is flush with all surrounding surfaces. 6. Choose a design which integrates the scanner and scale to eliminate extended reaches and lifts during weighing tasks. 7. Provide an easily accessible bag stand at a height 13 - 17 inches (33 43.
Scanner Usage Scanner Usage 1. Minimize handling of heavy/bulky products. Leave these items in the cart and use an alternative entry method such as key entry of short PLUs, or handheld scanning. 2. Regularly train cashiers in proper scanning methods and ergonomics principles, such as: • Develop a smooth fluid motion during scanning, sharing work equally between hands. • Use the entire hand for grasping and lifting items.
Service Access Requirements — Routine operations such as ‘zero- ing’ and calibration do not require removal of the scanner from the checkstand or disassembly of the product. The installer should plan service access for the AC/DC Power Supply and cables. Recommended Power Installation — Since the typical grocery environment includes conveyor belts and electric motors, care should be taken to ensure that the scanner has a supply of “clean” power (power without excessive electrical noise).
Ventilation and Spacing Vertical Clearance — Provision must be made to allow adequate space above the scanner bonnet for removal and replacement of an L-shaped platter. Optimal clearance permits the platter to be grasped at its top vertical edge and lifted for removal without obstruction (such as a fixed keyboard mount or any type of enclosure). Should such an enclosure be unavoidable, an alternate method of platter removal using two coins may be employed, however a minimum vertical clearance of 1.5” (3.
• A source of air that provides adequate cooling by convective air flow. DO NOT place the scanner in a close-fitting, fully enclosed checkstand. Provide a MINIMUM of 16 square inches (103.2 square centimeters) of air intake from below the installation for sufficient convective cooling. NOTE If motors, conveyor belts, or other heat producing equipment are located near the scanner, forced air ventilation may be required. In most installations, a 30 cfm (.
Power Installation Power Installation Reference the wiring diagram in Figure 2-6 for the recommended fusing arrangement. Grounding The AC/DC Power Supply should have an AC outlet with a clean earth ground. If you are not sure how to verify the amount of electrical noise (interference) on the power line, ask a qualified electrician to measure the input line voltage. Figure 2-6.
Liquid Spills and Moisture Select a checkstand design which allows fluids to flow through, and directs liquids away from any electronic equipment or storage areas. Counter Cutout The most important consideration when planning the counter opening for the scanner is the operator’s comfortable reaching distance. The ideal, ergonomically sound installation allows items to be directed within easy reach, and a scanning area requiring no lifting or special orientation of items.
Counter Cutout 3. Install the AC/DC Power Supply, the Remote Scale Display cable (if Remote Display is used) and the interface cable(s) observing the following: Interface cables (and display cable, if applicable) should be routed away from all highly inductive electrical devices, like motors and conveyor belts, and even away from the unit’s power cable if possible. Cables should be easy to remove in the event that replacement is required. A little planning now will save a lot of frustration later. 4.
Figure 2-7. Typical Checkstand Design & Cutout Location Remote Display Conveyor POS Terminal & Printer Optional Item Diverter Deadplate 6.3" (16.
Counter Cutout Figure 2-8. Medium Shelf Models 8302/8304/8402/8404 Cutout Dimensions Models 8302/8304/8402/8404 (Medium Shelf) Minimum Cutout Dimensions Max. Radius = 0.25" (0.635cm) Optional Leveling Feet 4x 15.825" (40.2cm) min. 11.625" (29.53cm) min. 1.76" (4.47cm) Leveling Feet 6.89" (17.5cm) Models 8302/8304/8402/8404 (Medium Shelf) Supports 4.08" (103.6mm) Shelf/ Support Rails 10.83" (27.5cm) Liquid Drainage Support Rails Liquid Drainage Figure 2-9.
Figure 2-10. Medium Flanged Models 8302/8304/8402/8404 Cutout Dimensions Models 8302/8304/8402/8404 (Medium Flanged) Minimum Cutout Dimensions 18.00" (45.7cm) 16.625" (42.23cm) Max. Radius = 0.25" (0.635cm) 4x Rail 3.06" (7.77cm) 0.75" (1.905cm) 11.625" (29.53cm) (Center Line) Rail 3.06" (7.77cm) 0.75" (1.905cm) If leveling feet are needed, use the placement shown here, represented with plus signs (+). 0.375" (0.952cm) 0.375" (0.952cm) Models 8302/8304/8402/8404 (Medium Flanged) Supports 18.
Counter Cutout Figure 2-12. Long Shelf Models 8303/8305/8403/8405 Cutout Dimensions Models 8303/8305/8403/8405 (Long Shelf) Cutout Optional Leveling Feet Max. Radius = 0.25" (0.635cm) 4x 17.87" (45.4cm) 11.625" (29.53cm) 1.76" (4.47cm) Leveling Feet 6.89" (17.5cm) Models 8303/8305/8403/8405 (Long Shelf) Supports 4.08" (10.36cm) Shelf/ Support Rails 10.83" (27.5cm) Liquid Drainage Liquid Drainage Support Rails Figure 2-13.
Figure 2-14. Long Flanged Models 8303/8305/8403/8405 Cutout Dimensions Model 8303/8305/8403/8405 (Long Flanged) Cutout 20.00" (50.8cm) 18.625" (47.308cm) Max. Radius = 0.25" (0.635cm) 4x Rail 3.06" (7.77cm) 0.75" (1.905cm) 11.625" (29.53cm) (Center Line) Rail If leveling feet are needed, use the placement shown here, represented with plus signs (+). 3.06" (7.77cm) 0.75" (1.905cm) 0.375" (0.952cm) 0.375" (0.952) Model 8303/8305/8403/8405 Supports 20.00" (50.8cm) 0.75" (1.9 cm) 1.5" (3.8 cm) 0.
Installation Overview Installation Overview The preceding Site Preparation Overview dealt with installed location and counter preparations to accommodate the scanner or scanner/scale. Having completed those steps, physical installation of the scanner or scanner/scale can begin. The following instructions apply to all models. This chapter describes: 1. Unpacking the unit. 2. Verifying operation before connecting to a POS system. 3. Routing and connecting cables. 4.
• Carefully lift off the L-Platter as shown in Figure 2-22 and remove the protective foam pieces securing the weigh mechanism. Set the platter back in place. For added protection during shipment, the L-Platter is covered with a tightfitting layer of vinyl. This vinyl layer MUST BE REMOVED before placing the unit into service.
Installation Overview Scale Diagnostic Mode To enter Scale Diagnostic Mode, press the Scale Zero Push Button for approximately four seconds. Six rapid tones will be sounded, indicating the unit is leaving normal operation and entering Scale Diagnostic Mode. The Remote Display will flash a ‘1’ across the display while the dignostic routine is being run. When diagnostics are completed successfully, the display will indicate that the unit has passed the diagnostic test by displaying PASS .
Figure 2-16 provides physical dimensions for the AC/DC Adapter (part number 8-0582). Figure 2-16. Physical Measurements: AC/DC Adapter 1.23" (3.1 cm) 1.97" (5 cm) 5" 3.3 m) c (8.5 Remote Scale Display Placement/Installation The modular Remote Display is designed so that single display heads can be stacked to form a dual display as shown in Figure 2-17a in order to address the specific viewing needs of both the customer and the cashier.
Remote Scale Display Placement/Installation Viewing Angle The optimum display angle is directly facing the viewer. Tilt and rotatioin adjustments can be made as shown in Figure 2-17b. To ensure that displays are easily readable for customers/cashiers of average height, display heads should be between 48” to 60” (122 to 152 cm) from the floor. Check with local Weights and Measures authorities regarding proper positioning of scale displays used in retail trade. NOTE Figure 2-17.
Remote Display Cabling Your installation should also take into account the routing of Remote Display cabling. Ensure that distance and obstacles spanned by the routed cable will not kink, pinch or stretch it. Also keep in mind you may need to drill a hole through which to route it. NOTE The Remote Scale Display connector end may be secured with a rubber band during shipping to prevent damage to the “locking tabs” (see Figure 2-19). After routing the cable, remove this rubber band before connecting.
Remote Scale Display Placement/Installation Figure 2-18. Physical Measurements: Remote Display 18.5mm Dual Display Single Display 28.4mm 60mm 60mm 112mm 112mm 329mm 264mm 292.5mm 325mm 227.5mm 116.39mm 116.39mm 25.5mm 41.99mm 85.1mm 5. Feed the entire length of the Remote Scale Display interface cable through the cable routing hole so that the assembled Remote Scale Display can be positioned over the mounting screw holes. 6. If present, remove the rubber band from the connector end. 7.
Figure 2-19. Remote Scale Display Mounting 36" (91cm) 48 - 60" (122 - 152cm) 24" (61cm) Dual Display Heads 11.5" (29cm) Mounting Example Single Display Head (optional cable routing) Figure 2-20. Remote Scale Display Mounting Template 116.39mm 41.99mm 85.1mm 2-24 25.
Set-Up & Installation Set-Up & Installation These setup and installation procedures assume that you have already prepared your checkstand to receive the scanner or scanner/scale. If you have not already made the counter cutout and routed power and interface cables, do so now as described in the previous instructions. If your checkstand has been prepared, proceed as follows: Set-up 1. Place the scanner on the checkstand next to the counter cutout. 2.
Figure 2-21. Connecting Cables to the Scanner/Scale Control Panel Service Loop Scanner Right Profile Scanner Left Profile 0.00 EAS Port EAS PORT Aux. Port AUXILIARY PORT Power POS Terminal POWER · Test Port AC Brick Input Connection to OR external EAS device. · On Screen Programming (OSP) Power off Terminal Controls EAS deactivation system.
Set-Up & Installation Installation 1. Make sure that all cables are firmly attached (except that the AC/ DC power supply should not be connected to the AC outlet yet). Reference Figure 2-21. 2. Remove the platter to gain access to the interior lift handle. Grasp the platter in the positions shown in Figure 2-22 and gently lift it from the scanner. If the top edge of the platter is blocked, you may find it easier to grasp the platter vertical bezel as shown in Figure 222b.
3. Rotate the Interior Lift Handle up as shown in Figure 2-23 and hook the fingers of both hands in the lift handles indicated. DO NOT attempt to lift the unit using the plastic edges, scale frame, or any features other than the lift handles. 4. Lower the unit into the counter opening, ensuring that none of the cables are pinched, pierced or crimped. 5. Re-install the Platter and verify that it is flush or just below flush with the countertop.
Chapter 3 Problem Isolation In the event of a suspected functional problem, use the troubleshooting references provided in this chapter. This useful information will help you to identify and resolve the cause of the problem. The scanner/scale has a number of features that indicate when a scanner or scale problem occurs.
Operational Tests These are the tests that run continually during Normal Operation and Sleep Mode. Firmware checks all subsystems, accessory connections and the POS interface to verify everything is operating normally. If a problem is detected at any time, a long, low tone is sounded, an error code is shown on the 7-segment display, and operation may be halted. If you press the Volume/Tone Push Button at that time, a series of tones will be sounded that matches the error code displayed.
Error Codes Error Codes If an error is detected, the scanner will sound a long low tone (for one second) and alternately flash its LEDs, indicating a failure. Following the long low tone, an error code will appear on the 7-segment display (refer to Figure 3-1). Pressing the Volume/Tone Push button will cause the scanner to sound a series of beeps corresponding to that error code. Table 3-1 on the following page describes what these codes mean and what action should be taken for each.
Table 3-1. Error Codes Error Code Probable Cause Corrective Action Configuration No POS interface has been selected (Null interface). See Chapter 5, Interface Type to select the required interface using programming bar codes. 1 Configuration Error See Chapter 5, Programming, for details about configuring the scanner using programming bar codes. 2 Interface Board Unplug unit and call technical support personnel. 3 Motor Unplug unit and call technical support personnel.
Error Codes Figure 3-1.
Scale Error Reporting Scale diagnostics uses the Remote Scale Display and the Zero Status lamp to communicate specific scale failures. The following chart shows the Remote Display messages, the Scale Status lamp indication, the problem that the scale is experiencing and what action should be taken. When troubleshooting, always remember to check all cable connections first before proceeding with other problem isolation steps.
Scale Error Reporting Remote Display -0- Scale Status Lamp Off Problem Description Cannot zero at power- up or weight remains on scale for more than 2 minutes or weight has not returned to zero between POS weight requestsa. Action Required - Check debris chutes. - Verify that the weigh platter moves freely. - Remove item(s) from scale - Press Scale Zero Push Button - for more information. - If the scale still fails to zero, recalibrate the scale. a. This is a configurable feature.
Figure 3-2. Problem Isolation: Remote Display REMOTE DISPLAY START Is the unit configured for a Remote Display ? NO Scanner-scale models that include a Remote Display when shipped from the factory, are configured for use with the display. If you're unsure of the settings for your unit, contact Tech Support. Use the programming bar codes in Chapter 5 to enable operation using a Remote Display.
Chapter 4 Calibration A number of situations require the scale to be calibrated. They are: • at initial installation of the scanner/scale • if the scale cannot be re-zeroed • if diagnostics indicate a calibration error • the weigh module has been replaced Follow the procedures on the following pages to ensure that the scanner/ scale will meet Weights and Measurement requirements.
Description of Calibration Sequence The Calibration Sequence sets the scale to an accurate reference point for weighing. This process involves the use of a Field Standard Weight Set (18.5-kilograms) for Metric. Once calibration has been successfully completed, the scanner/scale uses the certified weight as a reference for subsequent weighing activities. These verification procedures follow the U.S. National Institute of Standards and Technology 44 Handbook guidelines for bench/counter scale installations.
Motion Test Motion Test This test verifies that the scale will not ‘zero’ when the weighing surface of the scanner/scale is in motion. 1. Verify that the Yellow LED1 is on and the Remote Display reads 0.000 kilograms. 2. Press lightly on the weigh platter of the scanner/scale with one hand and at the same time press and release the Zero Push Button on the operator’s panel. The Yellow LED should turn Off and the Remote Display should not display 0.000 kilograms. 3.
Preparing the Scanner/Scale for Calibration 1. Assure that the scanner/scale is stable, secure and properly installed. (Refer to Chapter 2, Site Preparation and Installation, for instructions on the proper installation of the scanner/scale). 2. Power-up the scanner/scale. 3. Allow the unit to reach temperature equilibrium for at least one hour. If the scanner/scale is already at room temperature, allow at least 15 minutes for acclimatization. 4.
Calibrating the Scale Figure 4-1. Calibration Switch Access Spider Calibration Switch 4. Press and release the Calibration Switch to place the scanner/scale in Calibration Mode. The scanner/scale will sound a tone indicating it is in Calibration Mode. If the motor was spinning when you initiated Calibration Mode, the motor will stop and the Yellow LED will begin flashing indicating the scale is in Calibration Mode. The display will show the message “ESCL” (empty scale). 5. Reinstall the weigh platter.
8. The Yellow LED will extinguish for approximately 10 seconds and the Remote Display will alternately display and until the scale is ready to proceed. 9. If the calibration was successful, the speaker sounds a single tone, the Scale Status LED begins blinking again, and “End-” appears in the Remote Display. 10.
Calibration Verification (Kilograms) Calibration Verification (Kilograms) Once you have completed the calibration sequence, you may be required to perform these step-by-step verification procedures. These procedures follow the National Institute of Standards and Technology Handbook-44 guidelines for grocery scale installations. You may be required by state or local law to have these procedures performed by a certified technician or verified by a proper official.
8. Place an additional 200 grams on the center of the weighing surface and check that the display reads 1.000 kg. 9. Increase the weight on the scale to 7.50 kg on the center of the weighing surface and check that the display reads between 7.495 and 7.505 kg. 10. Remove the weights and verify that the display reads 0.000 kg. You have completed the Increasing-Load Test (Phase 1).
Calibration Verification (Kilograms) Figure 4-2. European Shift Test (Metric) A B CENTER A B TER CEN C C D D Increasing- Load Test (Phase 2) After completing the Shift Test, you must complete the Increasing Load Test using 10.00, 12.50 and 15 kilograms of weight. NOTE The upper limit of the scale is configurable according to POS interface type and may not necessarily be set at 15 kilograms, which is the standard setting. For this test, continue to place weights in 2.
5. You have completed phase two of the increasing load test. Blanking Test This test ensures that the scanner/scale will indicate its weighing capability has been exceeded if a weight greater than 0.82 over its maximum upper weight limit is placed upon the unit. 1. Place weights that total the upper limit plus 0.82 kilograms on the weigh platter. For example: If the upper limit is set at 15 kilograms, place weights equaling 15.82 kilograms. 2.
Calibration Verification (Kilograms) Decreasing-Load Test This test ensures that the scanner/scale responds properly when a heavy object is followed by a significantly smaller object. 1. Place weights that total 15.8 kilograms. If the upper weight limit for your scale is not set at 15 kilograms, begin by placing weight equaling your upper limit setting plus 0.8 kilograms. NOTE 2. Remove weights to leave 10 kilograms on the scale and verify that the display shows between 9.990 and 10.010 kilograms. 3.
NOTES 4-12 Magellan® 8300/8400
Chapter 5 Programming Entering and Exiting Programming Mode. Use the bar code label below to enter and exit (‘switch” into and out of) Programming Mode.
Return to Factory Settings Scan this bar code to return the scanner to the default settings configured at the factory for the currently active interface. This bar code is typically used to return the scanner to a “known” operating state when the present programming status is not known, faulty, or suspect. Use this bar code with caution, since it will reset ALL features that may have been programmed since the scanner’s installation.
Scale Features Scale Features Scale Enable Use this feature to enable or disable scale operation. Recalibration/recertification may be required when adding scale functionality. Consult your local Weights and Measures authority. NOTE If this feature is enabled the scanner will expect that it is to function as a scanner-scale, and will indicate an error if it is not a scale-equipped unit. See Chapter 3, Error Codes, for more information. To set this feature: 1. Scan the SWITCH bar code. 2.
Scale Enforced Zero Return This feature enables/disables the enforced zero return of the scale. Three settings are available for this feature: • Disable • Scale Must Return to Zero Weight Within Two Minutes — Scale will require re-zeroing if a non-zero weight is left on for more than two minutes or if the scale is below zero.
Scale Features Scale Enforced Zero Return — continued Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Scale Enforced Zero Return — continued Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Scale Features Scale Interface Type Use this feature to select the scale interface type. Choices are: • No Scale Interface • RS-232 — SASI • RS-232 — ICL To set the Scale Interface Type: 1. Scan the SWITCH bar code. 2. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. 3. Complete the programming sequence by scanning the SWITCH bar code.
Scale Interface Type — continued Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Scale Features Scale Calibration Notification When enabled, this feature allows the host to be notified of a calibration event. To set this feature: 1. Scan the SWITCH bar code. 2. Scan your selection from the two bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. 3. Complete the programming sequence by scanning the SWITCH bar code.
Scale Intercharacter Delay Sets the delay between the end of one character and the beginning of the next, in 10 millisecond increments. To specify the intercharacter delay: 1. Scan the SWITCH bar code. 2. Scan the bar code below, SCALE INTERCHARACTER DELAY. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. 3. Scan the appropriate digits from the keypad in Appendix A that represent the desired delay.
Scale Features Remote Display — Enable/Disable The scanner-scale can be configured to operate with or without a Remote Display. Recalibration/recertification may be required when adding a Remote Display. Consult your local Weights and Measures authority. NOTE If this feature is enabled the scanner-scale will expect that it is connected to a Remote Display, and will indicate an error if one is not. See Chapter 3, Error Codes, for more information.
Interface Related Features Interface Type Specifies the current scanner interface. INTERFACE (I/F) TYPE RS-232 Standard RS-232 Wincor-Nixdorf RS-232 Single Cable IBM USB IBM Port 17 Null Interface a. I/F I.D. NUMBERa 05 12 20 45 04 NOT USER-SELECTABLE 7-segment FRU display indicates 0 at start-up (accompanied by trill beep for approx. 2 seconds) To access a scanner’s interface identification number, place the scanner in Scanner Diagnostic Mode and view the 7-segment FRU display.
Interface Related Features Interface Type — continued NOTE A new scanner may have been shipped from the factory with a Null Interface (no interface type selected) to ensure system compatibility at installation. In this case, the correct Interface Type programming bar code must be scanned first before the scanner can be used with a POS system. NOTE If the scanner’s interface type must be changed, always be sure that interface configuration is the FIRST item scanned during a programming session.
Interface Type — continued 4. Complete the programming sequence by scanning the SWITCH bar code. NOTE Once the correct interface has been set, it will be necessary to proceed to the appropriate pages in this manual that select parameters and options for that interface. For example, if RS-232 is selected, turn to the pages in this manual headed as features specific to the RS-232 interface. 5. Connect new interface cable(s).
Interface Related Features RS-232 Wincor-Nixdorf Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. CAUTION Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED.
RS-232 Single Cable Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. CAUTION Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED.
Interface Related Features IBM USB Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. CAUTION Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED.
IBM Port 17 Interface Selection Remember to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan. CAUTION Great care should be taken to select the correct interface type, since you can cause damage to the scanner and/or POS terminal by attempting to change to an incompatible interface. ALWAYS make interface selections with the host cable DISCONNECTED. Single cable installations require connection at the POS Terminal (host) port.
Interface Related Features NOTES Technical Guide 5-19
NOTES 5-20 Magellan® 8300/8400
Appendix A Keypad Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
Use the bar codes in this appendix to enter numbers and characters as you would select digits/characters from a keypad. Scan your selection from the bar codes below. You’ll need to cover any unused bar codes on this and the facing page to ensure that the scanner reads only the bar code you intend to scan.
ASCII Character Set The table on this page shows a set of ASCII characters and their corresponding Hex Values. The Hex Values in this table are needed for setting symbology specific label identifiers, as well as enabling custom prefix and suffix characters. ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No. ASCII Char. Hex No.
Australia Japan Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Latin America Datalogic Scanning SAS Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Singapore Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.
