User manual

ManualsBrandsDATALOGIC ManualsScannersBarcode scanner GRYPHON D4130 Linear imager White Hand-held

131

132

133

134

135

136

137

138

139

140

Table Of Contents

CONTENTS
GENERAL VIEW
INTRODUCTION
INSTALLATION
- GRYPHON™ DX30 INTERFACE CABLE CONNECTIONS
- OM-GRYPHON™ INTERFACE CABLE CONNECTIONS
- RS232 CONNECTION
- USB
- IBM USB POS
- WEDGE CONNECTION
- PEN EMULATION CONNECTION
- GRYPHON™ MX30 BATTERY MAINTENANCE
GRYPHON™ MX30 SYSTEM AND NETWORK LAYOUTS
- STAND ALONE LAYOUTS
- MULTIDROP STAR-SYSTEM™ NETWORK LAYOUTS
  - Host Master Layout
CONFIGURATION
- CONFIGURATION METHODS
- SETUP PROCEDURES
- GRYPHON™ DX30 SETUP
- GRYPHON™ MX30/OM-GRYPHON™ STAND ALONE SETUP
  - Using Multiple M-Series Readers With Same Cradle
  - Gryphon™ M/STAR-Modem™ in Stand Alone Mode
- GRYPHON™ M/STAR-SYSTEM™ SETUP
- INTERFACE SELECTION
- USB READER CONFIGURATION
- CHANGING DEFAULT SETTINGS
RS232 PARAMETERS
- Baud Rate
- Parity
- Data Bits
- Stop Bits
- Handshaking
- Ack/Nack Protocol
- Fifo
- Inter-character Delay
- Rx Timeout
- Serial Trigger Lock
USB PARAMETERS
- Handshaking
- Ack/Nack Protocol
- Fifo
- Inter-character Delay
- Rx Timeout
- Serial Trigger Lock
- Keyboard Nationality
- Fifo
- Inter-character Delay
- Inter-code Delay
- Control Character Emulation
- USB Keyboard Speed
WEDGE PARAMETERS
- Keyboard Nationality
- Caps Lock
- Caps Lock Auto-Recognition (IBM AT compatible only)
- Num Lock
- Inter-character Delay
- Inter-code Delay
- Keyboard Setting
- Control Character Emulation
PEN EMULATION
- Operating Mode
- Minimum Output Pulse
- Conversion to Code 39 and Code 128
- Overflow
- Output Level
- Idle Level
- Inter-Block Delay
DATA FORMAT
- Code Identifier
- Custom Code Identifier
- Header
- Terminator
- Special Keys
- Field Adjustment
- Field Adjustment Character
- Code Length Tx
- Character Replacement
- Address Stamping (Mx30 Series Only)
- Address Delimiter (Mx30 Series Only)
POWER SAVE
- Scan Rate
- Sleep State/USB Suspend
- Enter Sleep Timeout
- Standby
READING PARAMETERS
- Hand-Held Operation
- Stand Operation
- Hardware Trigger Mode
- Trigger-off Timeout
- Flash Mode
- Reads per Cycle
- Safety Time
- Beeper Intensity
- Beeper Tone
- Beeper Type
- Beeper Length
- PDF Decoding Recognition Intensity
- Good Read Spot Duration
- Automatic Operation Aiming Light
DECODING PARAMETERS
- Ink Spread
- Overflow Control
- Interdigit Control
- Decoding Safety
- Puzzle Solver™
CODE SELECTION
- EAN/UPC Family
- 2/5 Family
- Code 39 Family
- Code 128 Family
- Code 93
- Codabar Family
- MSI
- Plessey
- Telepen
- Delta IBM
- Code 11
- Code 16K
- Code 49
- PDF417
- RSS Codes
ADVANCED FORMATTING
- Concatenation
- Advanced Formatting
RADIO PARAMETERS
- Radio Protocol Timeout
- Power-Off Timeout
- Beeper Control for Radio Response
- Battery Type
- Single Store
REFERENCES
- RS232 PARAMETERS
- PEN PARAMETERS
- DATA FORMAT
- POWER SAVE
- READING PARAMETERS
- DECODING PARAMETERS
- RADIO PARAMETERS (MX30 SERIES ONLY)
- CONFIGURATION EDITING COMMANDS
- CONFIGURATION COPYING COMMANDS
- C-GRYPHON™ CONFIGURATION
- DEFAULT PARAMETERS FOR POS TERMINALS
TECHNICAL FEATURES
- GRYPHON DX30
- GRYPHON™ MX30
- OM-GRYPHON™ / C-GRYPHON™
- SYSTEM AND RADIO FEATURES
- STATUS INDICATORS
- READING DIAGRAMS
A HOST CONFIGURATION STRINGS
B CODE IDENTIFIER TABLE
C HEX AND NUMERIC TABLE

Exit and Save Configuration

ADVANCED FORMATTING

Ì$

?Î

Field Transmission

number of fields to transmit

ÌHK8Î

Read one number in the range 1 to 7 for the number of fields to transmit. Include only fields to

be transmitted.

ead the codes corresponding to the fields to transmit in the order in which they are to be

ansmitted. A field can be transmitted more than once. See example.

Ì12Î

field 2

field 3

Ì23Î

Ì34Î

field 4

field 5

Ì45Î

Ì56Î

additional field 1

additional field 2

Ì67Î

Ì78Î

Example:

Field Order Transmission

field 1

The barcode is divided into 3 defined fields plus 1 additional fixed field.

Transmit in the order: Field 2, Additional Field 1, Field 1, Field 2.

Number of Fields

to Transmit

+ 4 +

Field 2

Additional Field 1

Field 1

Field 2

127