Datasheet

Datalogic Memor™ Single
Ethernet-USB Host Cradle
The Datalogic Memor™ Single Ethernet-USB Host Cradle paired
with a Datalogic Memor™ mobile computer provides a solution
for the collection, decoding and transmission of barcode data.
Communication options for this accessory include Ethernet and
serial or USB and serial.
The cradle also functions as a charger both for the mobile
computer and a spare battery pack. The spare battery pack
recharging slot accommodates both 1100 mAh and 2000 mAh
Battery packs.
Figure 1 – Datalogic Memor™ Single Ethernet-USB Host Cradle
A) LED Indicators
B) Spare Battery Slot
C) Mini USB Connector
D) RS232 Connector
E) Power Jack
F) Ethernet Port with LED indicators
G) Switch Ethernet/USB
NOTE
Read this manual carefully before performing any
type of connection through the cradle.
The user is responsible for any damages caused by
incorrect use of the equipment or by inobservance of
the indication supplied in this manual.
NOTE
Do not attempt to disassemble the cradle, as it does
not contain parts that can be repaired by the user.
Any tampering will invalidate the warranty.
822000911 (Rev. A)
COMPATIBILITY TABLE
The Single Ethernet-USB Host Cradle new technology is not
compatible with previous versions of Datalogic Memor™.
The following table shows the compatibility between the
Datalogic Memor™ models and the two versions of the single
ethernet cradle.
To help visually identify the new and old devices a set of yellow
stickers has been included with the Datalogic Memor™ Single
Ethernet-USB Host Cradle. Please apply these as needed to the
front of your new devices to ensure expected communications.
944201014 DL-Memor+802.11g+BT+1DGS+WM6.1
944201015 DL-Memor+802.11g+BT+2D+WM6.1
944201016 DL-Memor+Batch+1DGS+CE5
944201017 DL-Memor+EdgeE+BT+1DGS+WM6.1
944201018 DL-Memor+EdgeE+BT+2D+WM6.1
944201019 DL-Memor+802.11g+BT+1DGS+CE5
944201022 DL-Memor+802.11g+BT+2D+CE5
944201023 DL-Memor+EdgeA+BT+1DGS+WM6.1
Datalogic
Memor™
Single
Ethernet-
USB Host
Cradle
94A151122
944201024 DL-Memor+EdgeA+BT+2D+WM6.1
944201001 DL- Memor 000-904-416 MIN+FNC
944201003 DL-Memor 001-904-416 BT,MIN+FNC
944201005 DL-Memor 600-904-416 WIFI6,MIN+FNC
Datalogic
Memor™
Single
Ethernet
Cradle
94A151116
944201007 DL-Memor 800-904-416 WIFI,MIN+FNC
The Datalogic Memor™ Single Ethernet-USB Host Cradle can be
used with device software versions starting at the following:
- WinMobile: Ver: 4.01, Build: 1.02.00.20090918
- WinCE: Ver: 4.01, Build: 3.12.105.20090918.
CHARGING AND COMMUNICATION
By inserting the Datalogic Memor™ into the cradle, data can be
transmitted to the host and batteries will automatically begin
charging.
In addition, a spare battery can be charged by inserting it into the
slot at the back of the cradle as shown in the following figure.
Figure 2 – Datalogic Memor™ Single Ethernet-USB Host Cradle and
Communication
SPARE BATTERY REMOVAL
Figure 3 – Correct removal
Figure 4 – Incorrect removal
LED INDICATORS
The LEDs positioned on the front part of cradle (see figure below)
indicate the cradle and spare battery charger status:
Figure 5 - LED Indicators
Front LED indicators
LED STATUS
Red Constant Spare battery charging*
Charger
Green Constant
Spare battery charge
completed
Power Green
Constant when the cradle is
powered
* During charging, the LED may turn off to indicate a temporary
suspension of charging.
Ethernet Connector LED Indicators
Solid Green 100 Mbps connection
Ethernet
Green
LED (right)
Off 10 Mbps connection
Off No link established
Solid Yellow Link established
Ethernet
Yellow
LED (left)
Flashing Yellow Link activity
A
B
C
D
F
G
E
Spare Battery
Charger LED
Power LED
Spare battery
Charge Slot with
Spare Battery
Inserted
Data Transmission and
Mobile Computer
Battery Charging