PowerScan® PBT7100 Base Station Quick Reference Guide
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
Table of Contents Statement of Agency Compliance ........................................................... 3 FCC Class B Compliance Statement .................................................. 3 Canadian Notice ............................................................................ 3 Solids and Water Protection ............................................................ 3 Power Supply ................................................................................ 3 Laser Cautions ..................
NOTES 2 PowerScan® PBT7100 Base Station
Statement of Agency Compliance Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Laser Cautions The imager may contain a laser pointer (this is a value-added option), which is certified in the U.S. to conform to the requirements of DHHS/CDRH 21CFR Subchapter J for Class II and IEC 60825-1 for Class 2 products. Class II (2) products are not considered to be hazardous.
Software Product Policy 2.2 End User shall not copy, modify, decompile, disassemble, reverse engineer, or otherwise reproduce or remanufacture the Software, whether modified or unmodified, nor sell, assign, sublicense, distribute, lend, rent, give, or otherwise transfer the Software to any other person or organization, for purposes other than as expressly provided in this Agreement, without Datalogic’s prior written consent. 3. Transfers, Support. 3.1 3.2 3.
TEMPORANEOUS, OR FUTURE AGREEMENTS OR DEALINGS BETWEEN THE PARTIES, WHETHER ORAL OR WRITTEN, EXCEPT AS SET FORTH IN A FUTURE WRITING SIGNED BY BOTH PARTIES. 8. Limitation Of Liability. EXCEPT AS PROVIDED IN SECTION 7, DATALOGIC SHALL NOT BE LIABLE FOR ANY CLAIMS AGAINST END USER BY ANY OTHER PARTY.
Getting Started Connection shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before connection and consult the manual for that equipment (if necessary) before proceeding. Figure 1 Base Station Connection and Routing — Fully insert the Power Cable and Interface (I/F) Cable connectors into their respective ports in the underside of the Base Station (see Figure 1).
Host Connection — Typically, the interface type was specified at the time your reader and/or Base Station was ordered, however you should verify before connection that the Base Station’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 2. Keyboard Wedge interface cables have a ‘Y’ connection where its female end mates with the male end of the cable from the keyboard and the remaining end at the keyboard port on the terminal/PC.
Getting Started Figure 3. Labeling and Nomenclature This illustration shows label placement ONLY. For actual regulatory, patent and other applicable information, view the labels on the product intself, or call your nearest sales or service office. Antenna Link Bar Code Link Button Amber LED Green LED Scanner Latch NOTE Regulatory Label (on underside) PowerScan® PBT7100 readers and Base Stations can be configured to be compatible with PowerScan® 7000BT imagers and Base Stations.
Select the desired interface by scanning the associated barcode below. INTERFACE SELECTION BARCODE RS-232 Standard RS-232 Wincor-Nixdorf RS-232 for OPOS/UPOS/ JavaPOS Wand Emulation IBM 46XX Port 5B IBM 46XX Port 9B USB HID POS USB Coma USB Keyboard USB Alternate Keyboard USB OEM a. 10 Download the correct USB Com driver from www.datalogic.
Getting Started Interface selection — continued INTERFACE SELECTION BARCODE Keyboard AT Keyboard Wedge for PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Standard Key Encoding Keyboard AT-NK Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard Keyboard AT-ALT Keyboard AT-ALT-NK Keyboard Wedge for AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Keyboard
Interface selection — continued Keyboard IBM-MB Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard Keyboard DIG-VT Keyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xx Keyboard USB-KBDApple 12 USB Keyboard for Apple computers PowerScan® PBT7100 Base Station
EUROPEAN DECLARATION OF CONFORMITY Datalogic Scanning, Inc. hereby declares that the apparatus specified below has been tested and found compliant to the following European Council Directives and Harmonized Standards: Apparatus: PowerScan PBT7100 System Directives: EMC 2004/108/EC Low Voltage 2006/95/EC R&TTE 1999/5/EC RoHS 2002/95/EC WEEE 2002/96/EC Standards: EN 301 489-1 v 1.6.1 reference EN 301 489-17 v 1.2.1:2002 EN 300 328 v 1.7.
Australia Japan Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Latin America Datalogic Scanning Sarl Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Singapore Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.
