Gryphon™ I GM4100 General Purpose Handheld Linear Imager Barcode Reader Quick Reference Guide
Datalogic Scanning, Inc. 959 Terry Street Eugene, Oregon 97402 Telephone: (541) 683-5700 Fax: (541) 345-7140 An Unpublished Work - All rights reserved. No part of the contents of this documentation or the procedures described therein may be reproduced or transmitted in any form or by any means without prior written permission of Datalogic Scanning, Inc. or its subsidiaries or affiliates ("Datalogic" or “Datalogic Scanning”).
Table of Contents Statement of Agency Compliance .......................................................... 1 FCC Class B Compliance Statement ............................................. 1 FCC RF Radiation Exposure Statement ............................ 1 Canadian Notice .................................................................................. 2 Software Product Policy .............................................................................. 6 Customers Under Software Support ..............
NOTES
Gryphon™ I GM4100 Quick Reference Guide Statement of Agency Compliance This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Statement of Agency Compliance Canadian Notice This equipment does not exceed the Class B limits for radio noise emissions as described in the Radio Interference Regulations of the Canadian Department of Communications. Le present appareil numerique n’emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la classe B prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada.
Statement of Agency Compliance Datalogic Scanning, Inc. GRYPHON™ PRODUCT SERIES END USER LICENSE AGREEMENT Notice to End User: The Datalogic Product you have acquired contains embedded Software, which is integral to the product's operation. This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement.
Statement of Agency Compliance 3.2 3.3 logic may elect not to terminate this Agreement or the granted licenses, but instead may elect to notify End User that End User is deemed to have ordered and accepted a license for each breaching use. End User shall pay Datalogic the applicable list price for such licenses as of the date of such breach.
Statement of Agency Compliance 7.2 7.3 7.4 provided, that 1) End User notifies Datalogic promptly in writing of the claim, 2) Datalogic controls the defense or settlement of the claim, and 3) End User cooperates fully with Datalogic in such defense or settlement. All notices of a claim should be sent to Datalogic Scanning, Inc., Legal Department, 959 Terry Street, Eugene, OR 97402.
Software Product Policy writing, and shall be effective when received, with evidence of receipt. Notices to Datalogic shall be sent to the attention of Contract Administration, Datalogic Scanning, Inc., 959 Terry Street, Eugene, OR 97402, or such other address as may be specified by Datalogic in writing. 11.3 Waiver. A party's failure to enforce any of the terms and conditions of this Agreement shall not prevent the party's later enforcement of such terms and conditions. 11.
Setting Up the Reader Setting Up the Reader Follow the steps below to connect and get your reader up and communicating with its host. 1. Install the Batteries 2. Connecting the Base Station 3. Select the Interface Type 4. Configure Other Settings (if not using factory settings for that interface) Battery Safety To install, charge and/or do any other action on the battery, follow the instructions in this manual. NOTE Before installing the Battery, read “Battery Safety” on the following pages.
Setting Up the Reader WARNING Do not discharge the battery using any device except for the scanner. When the battery is used in devices other than the designated product, it may damage the battery or reduce its life expectancy. If the device causes an abnormal current to flow, it may cause the battery to become hot, explode or ignite and cause serious injury. Lithium-ion battery packs may get hot, explode or ignite and cause serious injury if exposed to abusive conditions.
Setting Up the Reader CAUTION Always charge the battery at 32° – 104°F (0° - 40°C) temperature range. Use only the authorized power supplies, battery pack, chargers, and docks supplied by your Datalogic reseller. The use of any other power supplies can damage the device and void your warranty. Do not disassemble or modify the battery. The battery contains safety and protection devices, which, if damaged, may cause the battery to generate heat, explode or ignite.
Setting Up the Reader Install the Batteries NOTE Before installing the Battery, read “Battery Safety” on the preceding pages. Datalogic recommends annual replacement of rechargeable battery packs to ensure maximum performance. To install or change the battery of your reader, you must: 1. With a screwdriver, unscrew the battery cover screw. 2. Unplug the three screws securing the battery holder, and unplug the white connector.
Setting Up the Reader 3. Carefully lift out the gold contacts circuit, and remove the battery holder while letting the white connector pass through the hole in the battery holder (as shown in the picture below). Pass-through hole 4. Remove the old battery from its place (if present), and insert the new battery in the same position. 5. Replace the battery holder, plug in the connector and return the contacts circuit to its previous location.
Configuring the Base Station Configuring the Base Station The base charger/station may be configured in desk application to hold the reader in two different positions, either a horizontal or standing position, in order to provide the most comfortable use depending on needs. Standing Horizontal Changing the Base Station Position The base station is configured by installing one of two sets of mechanical parts that come with the cordless kit.
Configuring the Base Station 2. Using your thumbs, push open the plastic tabs on the bottom of the base to free the wing holders. Tab Tab 3. The stand can now be repositioned in either horizontal or standing position.
Configuring the Base Station Connecting the Base Station Figure 1 shows how to connect the Base Station to a terminal, PC or other host device. Turn off the host before connection and consult the manual for that equipment (if necessary) before proceeding. Connect the interface cable before applying power to the Base Station. NOTE Gryphon Mobile can also be Powered by the Terminal. The external power supply is recommended but not necessary.
Configuring the Base Station Figure 2. Options for routing the DC cord Please refer to the arrows depicted on the bottom of the base when placing the cables, detailed in Figure 3. Figure 3. Arrows showing routing Host Connection: Verify before connection that the reader’s cable type is compatible with your host equipment. Most connections plug directly into the host device as shown in Figure 4 on page 16.
Configuring the Base Station B Figure 4. Connecting to the Host Wa Ke W nd US or... yb ed oard g or... e M or... IB Power Connection : Plug the AC Adapter in to an approved AC wall socket with the cable facing downwards (as shown in Figure 1) to prevent undue strain on the socket. NOTE Gryphon Mobile can also be Powered by the Terminal. The external power supply is recommended but not necessary. When powered by the Terminal, the battery charger is automatically set as Slow charge.
Linking the Reader to a Base Station Linking the Reader to a Base Station RF Devices For RF devices, before configuring the interface it is necessary to link the handheld with the base. To link the handheld and the base, press the trigger to wake it and place it on the base. If the reader was previously linked to another base, you must first scan the Unlink action command before relinking to the new base. Unlink System and Network Layouts Stand Alone Layouts Figure 6.
System and Network Layouts Figure 7. Multiple Reader Layout In stand alone systems, each cradle is connected to a single Host. Figure 8. Multiple Stand Alone Layouts Many stand alone connections can operate in the same physical area without interference, provided all readers and cradles in the system have different addresses.
Using the BC40xx™ Radio Base Using the BC40xx™ Radio Base Base LEDs LEDs on the Gryphon I Base provide information about the Base’s status, as shown in Figure 9. Figure 9. Gryphon I Base LEDs YELLOW LED BUTTON RED LED — GREEN LED The following table describes the significance of each LED: LED STATUS Power on / Data Yellow On = Base is powered Yellow Blinking = Base receives data and commands from the Host or the Reader. Charging Red On = the Battery is in progress.
Programming Display The Gryphon I is also available with an optional Display. The FSTN Display with white LED backlight provides additional information. Figure 10. Gryphon™ I Display Programming The reader is factory-configured with a set of standard default features.
Programming Select the Interface Type Upon completing the physical connection between the reader and its host, proceed directly to Interface Selection on page 22 for information and programming for the interface type the reader is connected to (for example: RS-232, Keyboard Wedge, USB, etc.) and scan the appropriate barcode to select your system’s correct interface type.
Interface Selection Interface Selection Each reader model will support one of the following sets of host interfaces: General Purpose Models: RS-232, RS-232 OPOS, USB, Key- board Wedge Retail Point of Sale Models : RS-232, RS-232 OPOS, USB, IBM 46XX Configuring the Interface Scan the programming barcode which selects the appropriate interface type matching the system the reader will be connected to.
Interface Selection RS-232 (continued) RS-232 for use with OPOS/UPOS/JavaPOS Select RS-232 OPOS USB Com to simulate RS-232 standard interface Select USB-COM-STDa IBM IBM-46xx Port 5B reader interface Select IBM-P5B IBM-46xx Port 9B reader interface Select IBM-P9B USB-OEM USB-OEM (can be used for OPOS/UPOS/JavaPOS) Select USB-OEM a. Download the correct USB Com driver from www.datalogic.
Interface Selection KEYBOARD AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/ Standard Key Encoding Select KBD-AT Keyboard Wedge for IBM AT PS2 with standard key encoding but without external keyboard Select KBD-AT-NK AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Select KBD-AT-ALT Keyboard Wedge for IBM AT PS2 with alternate key encoding but without external keyboard Select KBD-AT-ALT-NK 24 Gryphon™ I GM4100
Interface Selection KEYBOARD (continued) PC/XT w/Standard Key Encoding Select KBD-XT Keyboard Wedge for IBM Terminal 3153 Select KBD-IBM-3153 Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make only keyboard Select KBD-IBM-M Keyboard Wedge for IBM Terminals 31xx, 32xx, 34xx, 37xx make break keyboard Select KBD-IBM-MB Quick Reference Guide 25
Interface Selection KEYBOARD (continued) Keyboard Wedge for DIGITAL Terminals VT2xx, VT3xx, VT4xx Select KBD-DIG-VT USB Keyboard with standard key encoding Select USB Keyboard USB Keyboard with alternate key encoding Select USB Alternate Keyboard USB Keyboard for Apple computers Select USB-KBD-APPLE WAND EMULATION Wand Emulation Select WAND 26 Gryphon™ I GM4100
Keyboard Interface Keyboard Interface Use the programming barcodes to select options for USB Keyboard and Wedge Interfaces. Standard Factory Settings Reference the Gryphon™ I GD4100/GM4100 Product Reference Guide (PRG) for a listing of standard factory settings. Scancode Tables Reference the Gryphon™ I GD4100/GM4100 PRG for information about control character emulation which applies to keyboard interfaces. Country Mode This feature specifies the country/language supported by the keyboard.
Country Mode COUNTRY MODE ENTER/EXIT PROGRAMMING MODE Country Mode = U.S.
Country Mode COUNTRY MODE (continued) Country Mode = Czechoslovakia* Country Mode = Denmark* Country Mode = France Country Mode = Germany Country Mode = Hungary* Country Mode = Italy *Supports only the interfaces listed in the Country Mode feature description Quick Reference Guide 29
Country Mode COUNTRY MODE (continued) Country Mode = Japanese 106-key* Country Mode = Norway* Country Mode = Poland* Country Mode = Portugal* Country Mode = Romania* Country Mode = Slovakia* *Supports only the interfaces listed in the Country Mode feature description 30 Gryphon™ I GM4100
Country Mode COUNTRY MODE (continued) Country Mode = Spain Country Mode = Sweden Country Mode = Switzerland* *Supports only the interfaces listed in the Country Mode feature description Quick Reference Guide 31
Caps Lock State Caps Lock State This option specifies the format in which the reader sends character data. This applies to keyboard wedge interfaces. This does not apply when an alternate key encoding keyboard is selected.
Numlock Numlock This option specifies the setting of the Numbers Lock (Numlock) key while in keyboard wedge interface. This only applies to alternate key encoding interfaces. It does not apply to USB keyboard.
Technical Specifications Technical Specifications The following table contains Physical and Performance Characteristics, User Environment and Regulatory information. Item Description Physical Characteristics Color White/Gray Black/Gray Dimensions Height 7.1”/181 mm Length 3.9”/100 mm Width 2.8”/71 mm Weight (without cable) Approximately 8.7 ounces/246 g (reader with display) 8.
Technical Specifications Item Description Print Contrast Minimum 15% minimum reflectance Decode Capability UPC/EAN/JAN, P2 /P5 add-ons; Code 39; Italian Pharmacode 39; Code 128; C128 ISBT; Code 128 addons; I 2 of 5; Standard 2 of 5; Code 11;Codabar; EAN 128; Code 93; MSI; GS1 DataBar™ Omnidirectional, GS1 DataBar™ Limited, GS1 DataBar™ Expanded; Code4, Code5. Interfaces Supportedd RS-232 Std, RS-232 Wincor-Nixdorf, RS-232 OPOS, IBM 46xx (ports5B and 9B), USB Com Std.
Technical Specifications Item Description Regulatory Electrical Safety EMI/RFI UL 60950, CSA C22.2 No. 60950, IEC 60950 433 MHz model 910 MHz model Europe - CE, Russia – Gost; USA/Canada – FCC/IC; Australia – Ctick; Pending: China – SRRC; Mexico – NOM + Cofetel Singapore – IDA, Pending: Brasile – Anatel LED class safety IEC Class 1 Radio Features Working Center Frequency Range (in open air) 433MHz model 910MHz model 433.920 MHz 910.
LED and Beeper Indications LED and Beeper Indications The reader’s beeper sounds and its LED illuminates to indicate various functions or errors on the reader. An optional “Green Spot” also performs useful functions. The following tables list these indications. One exception to the behaviors listed in the tables is that the reader’s functions are programmable, and may or may not be turned on. For example, certain indications such as the power-up beep can be disabled using programming barcode labels.
LED and Beeper Indications INDICATION DESCRIPTION LED BEEPER Reader Disabled The reader has been disabled by the host. The LED blinks continuously N/A Green Spot is on continuously While in Stand Mode or Trigger Stand Mode the green spot shall be on while in stand watch state. N/A N/A Green Spota flashes momentarily Upon successful read of a label, the software shall turn the green spot on for the time specified by the configured value.
Error Codes INDICATION DESCRIPTION Label Programming Mode Acceptance of Programming Configuration option(s) have been successfully programmed via labels and the reader has exited Programming Mode. Label Programming Mode Cancel Item Entry Cancel label has been scanned. LED BEEPER N/A Reader sounds one high frequency beep and 4 low frequency beeps followed by reset beeps. N/A Reader sounds two times at low frequency and current volume. a.
Base Station Indications Base Station Indications INDICATION LEDS Power-up Complete Yellow LED on Reader Disabled by the HOST or the communication with HOST is not established Yellow LED blinking ~1Hz Data/labels are transmitted to the HOST Yellow LEDs turned off for 100mSec Programming Mode Yellow LED blinks quickly Configuration alignment with the HH is in progress Red LED blinks quickly Battery charger in progress Red LED on Battery charger complete Green LED on Battery charger error Gr
Ergonomic Recommendations Ergonomic Recommendations CAUTION • • • • • • • • • • • In order to avoid or minimize the potential risk of ergonomic injury follow the recommendations below. Consult with your local Health & Safety Manager to ensure that you are adhering to your company’s safety programs to prevent employee injury.
Regulatory Information Imager Labeling Labels are shown here to illustrate their location only. Please view the labels on your product for actual details. Scanner Regulatory Label C R US 10 239045 N263 INC.
Regulatory Information WEEE Statement Waste Electrical and Electronic Equipment (WEEE) Statement English For information about the disposal of Waste Electrical and Electronic Equipment (WEEE), please refer to the website at www.scanning.datalogic.com. Italian Per informazioni sullo smaltimento delle apparecchiature elettriche ed elettroniche consultare il sito Web www.scanning.datalogic.com.
Warranty Warranty Datalogic warrants to Customer that Datalogic's products will be free from defects in materials and workmanship for a period of 3 years from product shipment. This warranty does not extend to batteries and cables. As consumable items batteries and cables carry a 90 day warranty from time of purchase for DOA (dead on arrival) defects.
Warranty NOTES Quick Reference Guide 45
Warranty NOTES 46 Gryphon™ I GM4100
DECLARATION OF CONFORMITY EC-056 Rev.: 0 Pag.: 1 di 1 09 Datalogic Scanning Group Srl Via S.
Australia Datalogic Scanning Pty Ltd Telephone: [61] (2) 9870 3200 australia.scanning@datalogic.com Japan Datalogic Scanning KK Telephone: 81 (0)3 3491 6761 japan.scanning@datalogic.com France and Benelux Datalogic Scanning SAS Telephone: [33].01.64.86.71.00 france.scanning@datalogic.com Latin America Datalogic Scanning, Inc Telephone: (305) 591-3222 latinamerica.scanning@datalogic.com Germany Datalogic Scanning GmbH Telephone: 49 (0) 61 51/93 58-0 germany.scanning@datalogic.
