Specifications

i50 Manual (5.10)
Page 59
© 2015 Datalink Systems, Inc.
www.datalinksystemsinc.com
ID
Name
Description
Default
122
I_JOILPRESS
J1708 Min oil pressure. Range=0-99 PSI
5
123
I_HEADCHANGE
Heading change reports. Range=0-90 degrees. 0=Off
0
124
I_HEADTIME
Time required to trigger heading change event. Range=0-64800 sec
10
125
I_IDLELIMIT
Max idle time allowed. Range=0-64800 sec. 0=No Limit
0
126
I_ENGINE1
Engine Hours (seconds)
0
127
I_ENGINE2
"
0
128
I_ODO1
Odometer (1/10 km)
0
129
I_ODO2
"
0
130
I_PERIODICWAKEUP
Time between wakeup events while sleeping (sec)
0
131
I_MAXGPSWAIT
Max time to wait for GPS signal during periodic wakeup (sec)
120
132
I_MAXSENDWAIT
Max time to wait for network during periodic wakeup (sec)
120
133
I_IRIDIUMTIME
Satellite time reporting limit in dual-mode. Range=0-64800 sec
0
134
I_IRIDIUMDIST
Satellite distance reporting limit in dual-mode. Range=0-65500 metres
0
135
I_GPSUDPPORT
UDP port for sending GPS data during a dial-up or Wi-Fi connection. Set to
zero to disable.
2000
136
I_DYNIRIDIUM
Send Unit ID over Iridium to allow modems to be swapped between units
(1=Yes 0=No)
0
137
I_STATUS
Status report interval (Bits 7-6: Units 00=Days 01=Hours 10=Min. Bits 5-0:
Interval). Firmware versions < 4.26 only support 0 and 1 (off and daily)
1
138
I_ALARMID
Current Alarm ID used by MDS
0
139
I_FULLHEADING
Send full heading (0-360 degrees) instead of 8-point compass heading. Adds
one byte to each position packet (1=Yes 0=No)
0
140
I_COM1FLOW
Turn flow control on for COM1 port (1=Yes 0=No)
0
141
I_COM2FLOW
Turn flow control on for COM2 port (1=Yes 0=No)
0
142
I_COM1ROUTE
COM1 route (0=COM1 1=RJ45 2=WiFi)
0
143
I_SLEEPPIN
Pin used to trigger sleep mode. Bit 7=polarity. Bit 6=report at start-up. Bit
5=Motion wakeup. Bits 2-0=Input # (0=IGN, 1=Input 1, 2=Input 2, 3=Input 3,
4=Input 4)
0
144
I_ROUTERIP1
Router IP address used by WiFi DHCP server
192
145
I_ROUTERIP2
"
168
146
I_ROUTERIP3
"
0
147
I_ROUTERIP4
"
1
148
I_WIFICHANNEL
WiFi Channel Number (1-11)
6
149
I_FIREWALL
Limit WiFi traffic to IP addresses assigned in the I_IPx and I_GSIPx settings
(1=Yes 0=No)
1
150
I_ENCRYPT
Turn on AES-256 Encryption (1=Yes 0=No)
0
151
I_PAGERSYSTEMID
System ID for Grace pager system. Other IDs will be ignored. Set to zero to
process all IDs
0
152
I_PAGERTIMEOUT
Timeout (sec) before showing pager signal lost message
45
153
I_GARMIN
Bit 1=Send stop status. Bit 0=Send ETA updates
3
154
I_TRANSCONFIG
Bits 7-5=Sign On Time. Bits 4-2=Sign Off Time. Bit 1=Don’t buffer multiple
packets (existing transparent packets will be overwritten when new data is
received). Bit 0=Add position and date/time to transparent data packets
1
155
I_TOWALERT
Send alert if asset moves while engine is off (1=Yes 0=No)
1
156
I_ACCELZ
Accelerometer rotation around Z axis (radians*10000). Set to zero to
recalibrate. Set to 65535 to leave uncalibrated (no acceleration alerts will be
sent)
65535
157
I_MAXACCEL
Max allowed accelerating g-force (1/100 g). Set to zero to disable
50
158
I_MAXBRAKE
Max allowed braking g-force (1/100 g). Set to zero to disable
80