VS-1212-F 10/100/1000 Mb and 10 Gb VS-1224-F 10/100/1000 Mb and 10 Gb Data Access Switches QUICKinstall August 2012 541-0136-Q-A.
VS-1212-F and VS-1224-F Data Access Switches Table of Contents Section 1 Terms of Use 3 1 Copyright ................................................................................................................................... 3 2 License................................................................................................................................... Agreement 3 3 Proprietary .........................................................................................................
Terms of Use 1 3 Terms of Use The following terms and conditions relate to the use of this document. Please note that Datacom Systems Inc. reserves the right, at its entire discretion, to change, modify, add, or remove portions of these Terms of Use at any time. Please read the Terms of Use carefully as your use of this document is subject to the Terms of Use stipulated herein. 1.1 Copyright Copyright ©2012 by Datacom Systems, Inc. All rights reserved. Printed in the United States of America.
1.4 VS-1212-F and VS-1224-F Data Access Switches Certifications and Marks CAUTION: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Terms of Use 5 IMPORTANT: Rack Mount Instructions are included here to call the attention of installation technicians to pertinent safety and warning issues prior to the installation of the product as follows: A. Elevated Operating Ambient — If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment may be greater than room ambient.
2.1 VS-1212-F and VS-1224-F Data Access Switches What Shipped? 1 - VS-1212-F or VS-1224-F 2 - AC Line Cords 1 - DRL512-2M-R cables, DB9 M/F straight thru 2.2 Specifications VS-1212-F Ports: 12 - SFP; SFP+ VS-1224-F Ports: 24 - SFP; SFP+ Management Port (rear): RJ45 @ 10/100/1000 Mbs Full-Duplex Serial Port (rear): DB9 @ 115,200 bps; 8 data bits; Parity none; 1 stop bit; Flow control none Input Power Requirement: 100-240VAC 50-60Hz, 4.0-2.0 A Dimensions (H x W x D): 1.72 x 19.00 x 20.50 inch (4.
Overview 7 10G fiber transceivers: Finisar FTLX8571D3BCV SR/MM dual rate 1G/10G transceiver (SFP+) Finisar FTLX8571D3BCL SR 10G transceiver (SFP+) Finisar FTLX1471D3BCV LR/SM dual rate 1G/10G transceiver (SFP+) Finisar FTLX1471D3BCL LR 10G transceiver (SFP+) 1G copper transceivers: Finisar FCLF-8521-3 copper multi-rate transceiver (SFP) 1G fiber transceivers: Finisar FTLF8519P2BCL 1G 850nm MM fiber transceiver (SFP) Finisar FTLF8519P2BNL 1G 850nm MM fiber transceiver (SFP) Finisar FTL1318P2BTL 1310nm SM f
VS-1212-F and VS-1224-F Data Access Switches power the VS-1212-F and VS-1224-F, use of a second independent power source is strongly recommended to assure uninterrupted monitoring. To power the unit ON: Power ON by depressing the AC power switch bar icon located on the rear panel.
Overview 9 Furthermore, connecting the second AC input power socket to a different external power source circuit than the first AC input power source eliminates power as a single point of failure. The AC power switch is a rocker style switch. The circle icon depressed is OFF and the bar icon depressed is ON. To power the unit ON, depress switch bar icon. The powered ON VS-1212-F and VS-1224-F is indicated by the illuminated green POWER 1 and POWER 2 LEDs on the front panel. 2.
VS-1212-F and VS-1224-F Data Access Switches NOTE: For PCs without 9-pin serial ports, check with you product representative for available sources of a USB to RS-232 Plug-in Adapter. Step 2. Using a supplied AC Line Cord, plug the VS-1212-F Data Access Switch or VS-1224-F Data Access Switch into the external power source. Note that either POWER 1 or POWER 2 LED is illuminated green indicating power is available at the rear AC power socket to which the AC Line Cord is connected.
Network IP Address Configuration 11 Step 11. Disconnect the DRL512-2M-R serial cable from your VS-1212-F Data Access Switch or VS-1224-F Data Access Switch and proceed to install the VS-1212-F or VS-1224-F in your chosen network location. 4 Stand-Alone Installation This section will focus on a simple configuration which describes the typical VS-1212-F Data Access Switch and VS-1224-F Data Access Switch hardware installation at the network location of your choice. 4.
4.2 VS-1212-F and VS-1224-F Data Access Switches Port Connection This section will focus on the PORT connection of the typical VS-1212-F Data Access Switch hardware installation. The VS-1224-F Data Access Switch hardware installation is similar to the typical VS-1212-F Data Access Switch hardware installation. Step 1. Connect the network cables to PORT sockets as has been determined in your data access switch network layout.
Management Connection 5.1 13 Web Browser This section describes the intuitive Web Browser Graphical User Interface (GUI) Login session. Web Browsers supported are Microsoft Internet Explorer 8.0 and Mozilla Firefox 9.0.1. Only encrypted (HTTPS) web sessions are supported, unencrypted (HTTP) web sessions are NOT supported. Step 1. Users access the GUI through the Web Browser with the following address: https:// .
VS-1212-F and VS-1224-F Data Access Switches Step 3. If additional user operational GUI navigational help or information is necessary, detailed support, documentation and help can found on the Datacom Systems website http://www. datacomsystems.com. Step 4. In the upper right window Click 'Logout' to end the session> Step 5. Close the Web Browser. 5.2 TELNET or SSH Most network equipment and operating systems with a TCP/IP stack also support some kind of TELNET service server for remote connection.
Management Connection 15 IMPORTANT: For Host Name (or IP address), if initial IP Address HAS BEEN configured, as shown below, use the Local Area Network address setting input during initial 'SERIAL Port (DB9) Network IP Address Configuration 9 '. Otherwise, if initial IP Address HAS NOT BEEN configured, a direct-connect cross-over cable to PC and custom configured computer IP and Subnet must be set in order to use the factory default IP Address:192.168.1.1, Subnet Mask 255.255.0.0, Gateway: 192.168.1.
6 VS-1212-F and VS-1224-F Data Access Switches Customer Service Datacom Customer Service is available via telephone and Internet. Please leave a voice message and our Customer Service Staff will return your call as soon as possible. You may also find the assistance you need at our website: http://www.datacomsystems.com. Telephone: +1 315 463-9541 Internet website: http://www.datacomsystems.com 6.1 Warranty See http://www.datacomsystems.com for warranty detailed information. 6.
Datacom Systems Inc. 9 Adler Drive • East Syracuse, NY 13057 TEL: +1 315 463-9541 • FAX: +1 315 463-9557 http://www.datacomsystems.
