User manual

iv Technical Review UniSite User Manual
Figure 7-8. Input and Output Orbital Assemblies.....................................7-8
Figure 7-9. Note the Wire Colors and Positions.........................................7-9
Figure 7-10. Align the Slit in the Collar with the Slit in the Spindle.....7-10
Figure 7-11. Removing the Print Drive Motor (Dot Matrix Printer shown;
Thermal Printer similar)..............................................................................7-12
Figure 7-12. Removing the Print Head......................................................7-13
Figure 7-13. Remove the Track Springs.....................................................7-15
Figure 7-14. Remove the Track Springs.....................................................7-16
Figure 7-15. Removing the Air Cylinder...................................................7-18
Figure 7-16. Right Lead Screw Bearing Assembly...................................7-22
Figure 7-17. Beam Cable and Switch Locations.......................................7-26
Figure 7-18. Baffle Plate Reinstallation......................................................7-27
Figure 7-19. Removing the DIP Module from the Circuit Board...........7-29
Figure 7-20. Removing the Retaining Block .............................................7-29
Figure 7-21. Removing or installing the Contact Set...............................7-30
Figure 7-22. Removing the Configuration Blocks....................................7-31
Figure 7-23. Removing the Programming Block......................................7-31
Figure 7-24. Removing the Device Ejector Pin and Spring.....................7-32
Figure 7-25. Removing the Contact Set.....................................................7-32
Figure 7-26. Replacing the Defective Pins.................................................7-34
Figure 7-27. Pin Insulation Block in the Programming Module............7-35
Figure 7-28. PLCC Programming Module (Exploded View).................7-37
Figure 7-29. Test Site Clamp Assembly.....................................................7-39
Figure 7-30. Carriage Assembly .................................................................7-41
Figure 7-31. Input Assembly.......................................................................7-43
Figure 7-32. Output Tube Clamp Assembly.............................................7-48
Figure 7-33. Beam Assembly.......................................................................7-50
Figure 7-34. Main Plate Assembly..............................................................7-55
Figure 7-35. Thermal Printer Assembly ....................................................7-59
Figure C-1. ProMaster 2500 Wiring Diagram............................................ C-2
Figure C-2. ProMaster 2500 Handler Controller Board Layout (not to scale)
C-3
Figure D-1. An Example of ASCII Binary Format ....................................D-5
Figure D-2. An Example of TI SDSMAC Format......................................D-7
Figure D-3. An Example of Formatted Binary Format...........................D-10
Figure D-4. An Example of Formatted Binary Format...........................D-11
Figure D-5. An Example of Spectrum Format.........................................D-12
Figure D-6. An Example of ASCII Octal and Hex Formats...................D-19
Figure D-7. An Example of RCA Cosmac Format..................................D-21
Figure D-8. An Example of Fairchild Fairbug.........................................D-22
Figure D-9. An Example of MOS Technology Format...........................D-23
Figure D-10. An Example of Motorola EXORciser Format...................D-24
Figure D-11. An Example of Intel Intellec 8/MDS Format ...................D-25
Figure D-12. An Example of Signetics Absolute Object Format...........D-26
Figure D-13. An Example of Tektronix Hex Format..............................D-27
Figure D-14. An Example of Motorola EXORmacs Format ..................D-28
Figure D-15. An Example of Intel MCS-86 Hex Object..........................D-29
Figure D-16. An Example of HP 64000 Absolute Format......................D-31
Figure D-17. An Example of TI SDSMAC Format..................................D-33
Figure D-18. An Example of JEDEC Full Format....................................D-38
Figure D-19. An Example of JEDEC Kernel Mode Format....................D-46
Figure D-20. An Example of Tektronix Extended Format.....................D-47
Figure D-21. An Example of Motorola S3 Format..................................D-49