User manual

UniSite User Manual Technical Review iii
Figure 5-3. Beam Air Holes.........................................................................5-11
Figure 5-4. Power Supplies..........................................................................5-14
Figure 5-5. Missing Character Dots in Label Printout.............................5-22
Figure 5-6. Adjusting Label Calibration....................................................5-25
Figure 5-7. Print Shift (affects vertical position).......................................5-26
Figure 5-8. Label Calibration (affects horizontal position).....................5-26
Figure 5-9. Thermal Printer Ribbon Path..................................................5-29
Figure 5-10. Diagnostics Command Tree..................................................5-30
Figure 5-11. Inserting the Hood Interlock Switch....................................5-31
Figure 5-12. Optic and Microswitch Locations ........................................5-33
Figure 5-13. Adjusting the Dot Matrix Printer ADC Optic During Calibration
5-35
Figure 5-14. Thermal Printer, Front View, Showing the ADC Label Optic.
5-37
Figure 5-15. Locations of the Solenoids Under the Main Plate..............5-38
Figure 5-16. Solenoids on the Beam (test numbers shown)....................5-39
Figure 5-17. Location of the Motors...........................................................5-41
Figure 5-18. Recommended Orientation of Pin 1 for DIP and PLCC Devices
5-45
Figure 5-19. Interior View of the 2500’s Base............................................5-47
Figure 5-20. Print Head LEDs on Handler Controller Board.................5-47
Figure 5-21. Position of the 78-pin Connector on the Mass Storage Module
5-52
Figure 5-22. Test Points on the MSM 78-pin Connector .........................5-53
Figure 5-23. Removing the Ribbon Cassette.............................................5-58
Figure 5-24. Installing a New Dot Matrix Printer Ribbon Cassette.......5-58
Figure 5-25. Threading the Ribbon in the Thermal Printer....................5-59
Figure 5-26. Location of the Lead Screw and the Carriage.....................5-63
Figure 5-27. Adjusting the Track Height...................................................5-64
Figure 5-28. Input and Output Track Funnel Adjustment.....................5-65
Figure 5-29. Adjusting the Track Width Cables.......................................5-66
Figure 6-1. Power-up Failures (page numbers are in parentheses).........6-7
Figure 6-2. The Beam Does Not Pick Up the Device Correctly (page
numbers are in parentheses).........................................................................6-8
Figure 6-3. The Beam Does Not Insert the Device Correctly into the
Programming Module (page numbers are in parentheses) .....................6-9
Figure 6-4. Programming Failures (page numbers are in parentheses)6-10
Figure 6-5. Label Printing Problems, Dot Matrix Printer (page numbers are
in parentheses).............................................................................................. 6-11
Figure 6-6. Label Application Problems, Dot Matrix Printer (page numbers
are in parentheses)........................................................................................6-12
Figure 6-6 (continued). Label Application Problems, Dot Matrix Printer
(page numbers are in parentheses)............................................................6-13
Figure 6-7. The Beam Does Not Deliver the Device Correctly (page
numbers are in parentheses).......................................................................6-14
Figure 7-1. Opening the Power Input Assembly to Access the Fuse......7-2
Figure 7-2. Removing the Fuse.....................................................................7-2
Figure 7-3. Location of the Main Plate Screws...........................................7-3
Figure 7-4. Polarity of the Cables on the Programming Electronics Assembly
7-4
Figure 7-5. Remove the Module Clamp Assembly Screws ......................7-5
Figure 7-6. Lower the Clamp Assembly and Remove the Retaining Bar7-6
Figure 7-7. Programming Electronics Assembly Alignment ...................7-6