User manual

Table of Contents
x ProMaster 2500 User Manual
Figure 2-8. Adjusting Plate Height....................................................................................2-9
Figure 2-9. Loading Labels in the Dot Matrix Printer...................................................2-10
Figure 2-10. Installing the Labeler Ribbon Cassette in the Dot Matrix Printer.........2-12
Figure 2-11. Threading Labels in the Thermal Printer..................................................2-14
Figure 2-12. Threading a Ribbon in the Thermal Printer.............................................2-15
Figure 2-13. TaskLink Main Screen (Administrator Mode).........................................2-18
Figure 2-14. Labeler Setup Path (Local mode on the front panel) ..............................2-23
Figure 2-15. Changing the Label Calibration Value......................................................2-24
Figure 2-16. Changing the Label Placement Value .......................................................2-25
Figure 2-17. Changing the Dot Split Value.....................................................................2-26
Figure 2-18. Print Shift (affects vertical position)..........................................................2-27
Figure 2-19. Label Calibration (affects horizontal position) ........................................2-28
Figure 2-20. Location of Firmware EPROMs on the Main Controller Board............2-31
Figure 3-1. Overview of the Steps Involved in Creating Tasks.....................................3-3
Figure 3-2. Add Task Pull-down Menu............................................................................3-4
Figure 3-3. Add Task Dialog Box.......................................................................................3-5
Figure 3-4. Edit Task Dialog Box........................................................................................3-6
Figure 3-5. Illegal Bit Condition.........................................................................................3-8
Figure 3-6. ProMaster Dialog Box......................................................................................3-9
Figure 3-7. Selecting Orientation of Device Pin 1 in the Input Tube Using
TaskLink...........................................................................................................................3-10
Figure 3-8. Recommended Device Orientation in Input Device.................................3-11
Figure 3-9. Logic Device Parameters...............................................................................3-12
Figure 3-10. Memory Device Task...................................................................................3-14
Figure 3-11. Memory Parameters Dialog Box................................................................3-15
Figure 3-12. Commands Available under Setup ...........................................................3-19
Figure 3-13. Log File Format Compared to Task Statistics Screen..............................3-19
Figure 3-14. General Parameters Dialog Box .................................................................3-20
Figure 3-15. Serialization Parameters Dialog Box.........................................................3-22
Figure 3-16. The Serialization Process.............................................................................3-23
Figure 3-17. Utilities Pull-down Menu............................................................................3-27
Figure 3-18. Commands Available from the Options Pull-down Menu....................3-28
Figure 3-19. Selecting Security Options..........................................................................3-29
Figure 3-20. Password Screen for System Operators....................................................3-30
Figure 3-21. Configuring Operating Preferences...........................................................3-31
Figure 3-22. Selecting “Add Kit” from the Main Screen ..............................................3-32
Figure 3-23. Kits are a Series of Tasks in a Single Job...................................................3-33
Figure 3-24. Edit Kit Screen ..............................................................................................3-34
Figure 3-25. Naming the First Task in the Kit................................................................3-34
Figure 3-26. Adding the Second Task to the Kit............................................................3-35
Figure 3-27. Sample Message Presented to System Operator when Kit Is Run........3-36
Figure 3-28. Selecting the Batch File Command............................................................3-38
Figure 4-1. Overview of the Procedure for Starting a Task ...........................................4-3
Figure 4-2. TaskLink Operator Screen...............................................................................4-5
Figure 4-3. Enter Your Name on the Security Screen .....................................................4-6
Figure 4-4. TaskLink Main Operator Screen....................................................................4-6
Figure 4-5. Configuring Blocks on a Programming Module.........................................4-8
Figure 4-6. Configuration Box Compartments ................................................................4-9
Figure 4-7. Configuration Box Lid—Optional Configurations for 28-pin Module..4-10
Figure 4-8. Installing a Programming Module ..............................................................4-12
Figure 4-9. Adjusting the Track Width — Turning the knob clockwise opens all
three track sections together..........................................................................................4-13
Figure 4-10. Final Track Adjustment...............................................................................4-14