User`s guide

54 DL-WINDOWS™ V4.0 USER'S GUIDE
ACCESS = Entry into a restricted area.
AMBUSH = A special Code entered at the keypad when the User is forced
to unlock a device. The device unlocks but sends a silent alarm with no
indication at the keypad. Can be used to trip a relay, to alert security,
or trip a silent alarm on a Burglary Control Panel.
AUDIT TRAIL = A date/time stamped log of previous lock events.
BURGLARY CONTROL PANEL = Provides local alarm and remote
communication to request security for burglary/break-in. A relay output
used for Ambush can provide a silent alarm and call-for-help.
CLOCK
• REAL TIME CLOCK = An accurate built-in clock that allows date/
time stamping of events. The clock can be slowed or speeded up
to fine tune long term accuracy to within three minutes per year.
• CLOCK SETTINGS = Printout includes date, time, weekday, and
clock speed.
• CLOCK SPEED = The clock can be adjusted to allow faster/slower
speeds and therefore increasing clock accuracy.
CODE = Numeric sequence of numbers (such as: 1234) entered at the
keypad. If Star-Enter-Key is required, must be followed by a [:] key.
• AMBUSH CODE = See Ambush.
• BASIC USER CODE = User Codes assigned to User Numbers 12+
(except Users 297-300). (Does not allow programming)
• INSTALLER CODE = User Codes assigned to User Numbers 2
and 3. (Allows all programming except Master functions).
• INVALID CODE = A User Code that has not been programmed in
the lock.
• MANAGER CODE = User Codes assigned to User Numbers 4
through 6. (Allows most of the programming functions).
• MASTER CODE = User Code assigned to User Number 1. Default
(factory) Master Code is 123456. The User with the Master Code
has complete control of the lock.
• PRINT ONLY USER CODE = User Code assigned to Users 10 and
11. (Allows no programming except print functions).
• QUICK ENABLE USER 300 CODE = Refers to the User Code
entered by User 297 which (when entered at the keypad) enables
the User Code assigned to User 300 for one time only.
• QUICK PC ACCESS CODE = Permits upload/download to DL-
Windows Software on IBM/compatible computer running Microsoft
Windows 95, 98, or NT 4.0. Refers to the User Code for User 298.
• SERVICE CODE = User 300 User Code. Allows only one entry,
then needs to be re-enabled by the User 297 User Code to regain
access.
• SUPERVISOR CODE = User Codes assigned to Users 7, 8 and 9.
Can only program day-to-day operation.
• USER CODE = Code used by Users. Code is 3 to 6 numeric digits
long, allowing controlled entry.
• VALID CODE = An entered User Code that has been programmed
in the device.
COM PORT = A computer serial communications port used to
communicate with the Lock and/or Data Transfer Module.
DATA TRANSFER MODULE = A device that permits transfer of program/
data between a computer and the lock.
DATE = Month, Day and Year entered as MMDDYY.
DAY OF WEEK = Sunday through Saturday (where 1 = Sunday and 7 =
Saturday).
DEFAULT = "Default" settings are the original settings that were set at the
factory; in other words, it is the lock's original factory condition when the
lock was first taken out of its box. The default settings are permanently
encoded within the lock's fixed memory, and when the lock is first
started, or when power is removed and re-applied, the original factory
default settings are re-loaded and take effect.
DISABLE = Turn off.
DOOR AJAR = If access is granted with the lock, and the door is held open
beyond the pre-programmed amount of time, the lock will trip a ‘Door
Ajar’ event. If programmed, the lock will provide audible annunciation
and/or an auxiliary relay closure.
DOOR NUMBER = Identification of each door with a specific number (1-
2000). (Used with the AL-DTM and AL-DTM-II. For the AL-DTM-III,
see glossary entry "LockID").
DOWNLOAD = Send data to lock or AL-DTM.
EMERGENCY COMMANDS = For use only with the Trilogy Networx
™
wireless network, wireless commands can be sent to all wireless locking
devices in an Account during a crisis or other urgent situation: "Global
Lock Down", to lock all doors in the Account; "Global Passage", to
unlock all doors in the Account; and return all devices in the Account to
"normal" (non-emergency) operation. See OI352 for more information
regarding the wireless Networx
™
system, its supported locks and
features.
ENABLE = Turn on.
EVENTS = Recorded lock activity.
FUNCTION (also called Programming Functions) = are the numbers
used to program lock features (enabling/disabling Users, User Groups,
Passage Mode, Schedules, etc.).
FUNCTION CARDS (Used with the PL3000 lock only) = Nine standard
proximity cards labeled one through nine, enrolled into the PL3000 lock.
Each card can perform a specific function, such as initiating PC
communications or enrolling proximity cards. See WI1280 for more
information.
GROUP
• USER GROUP = Defining a User to specific Groups, allows User
entry when the Group is allowed entry.
• GROUP 1 DISARMS BURGLAR CONTROL = A Group 1 USER
CODE entry can disarm an alarm panel during a predefined
schedule. Should the Group 1 enter the lock outside of the
scheduled time, the alarm will not disarm. The alarm panel must be
armed through other means (such as an Alarm Panel Keypad). The
Burglary Alarm Panel must be programmed to disarm from an Armed
State Only and the zone input must be programmed for input
disarming.
• GROUP 1 ENABLES GROUP 4 USERS = A Group 1 USER CODE
entry during a predefined schedule will allow access to Group 4
Users.
• GROUP 1 PUTS UNIT IN PASSAGE = A Group 1 USER CODE
entry during a pre-defined schedule will unlock unit.
GUARD TOUR = A Guard Tour Code is used to log the movement of a
security guard as he or she makes rounds from one assigned guard tour
station to the next.
INSTALLER = See.... CODE, INSTALLER CODE.
KEYPAD = 10-numeric keys, : and special ; key.
Glossary