User`s guide

DL-WINDOWS™ V4.0 USER'S GUIDE 25
on each press of the green button; when SLEEP THEN POWER
DOWN appears, press and hold the green button to exit
Configuration Mode. Note: UNCONDITIONAL FLASH ERASE
erases all lock information and configured settings in the AL-
DTM. To reset the AL-DTM to its factory default settings,
remove the battery, press and hold the green button for 10
seconds, then replace the battery.
7. The unit may now be powered up with the new feature(s)
enabled.
Once AL-DTM is configured, it is ready for use. If Door Select
Mode was set to "ON" (in step 5 above), then the AL-DTM will
power up in "OPERATION MODE", which offers two choices: SELECT
and STD:
SELECT – If Select Mode is chosen (by pressing left button), you
can choose between three modes: PC Comm Mode, Lock
Mode, and Door Select Mode:
• PC Comm Mode is used to transfer programming between
the PC and the AL-DTM.
• Lock Mode is used to transfer information between the AL-
DTM and the Locks. The AL-DTM will automatically
identify the LockID to which it is communicating.
• Door Select Mode is used to transfer program and assign
LockID numbers from DL-Windows.
STD ("standard") – Standard Mode will automatically put AL-DTM
in PC COMM MODE when communicating with DL-Windows
and will put the AL-DTM in LOCK MODE when performing
communications with the locks. Standard Mode should be
used for all subsequent communication after LockID has been
assigned.
Note: The AL-DTM will only allow the selection of a LockID for
which it has valid data currently programmed. Care must be taken
to that ensure the correct data is being transferred to the correct
lock.
The AL-DTM may be configured for Foreign Language support
and the Door Select feature (see below). Warning: Entering the
following Configuration Mode will clear all data (lock information)
from memory.
1. Place AL-DTM into PC COMM
MODE. If not already in PC
COMM MODE, press green
button to enter this mode.
2. Press and HOLD both the left and green buttons on the AL-
DTM. After several messages appear, release the buttons
when the display reads:
When the display reads "CONFIG. LANGUAGE", the AL-DTM
has entered Configuration Mode.
Note: Pressing the green button allows you to step through
each configuration option in turn; after the last option, the list
repeats ("CONFIG. LANGUAGE" re-appears).
3. If you wish to configure the first option, Language, press and
hold the green button (otherwise press and release the green
button to skip to the next option shown in step 4).
Set the language (as shown above) with the left and middle
black buttons, then press the green button to select the
language AND exit this option.
4. The next option appears: CONFIG. FOR DTM-III MODE. For
DL-Windows 3.5x and above, this mode MUST be set to "ON".
Therefore, enter this option by pressing and holding the green
button. The following screen appears:
As shown above, the default setting is "ON". Press the green
button to both select DTM-III mode and exit this option.
5. The next option appears: CONFIG. DOOR SELECT MODE.
Enter this option by pressing and holding the green button.
The following screen appears:
As shown above, the default setting of "ON" should be
retained if LockID numbers have not yet been programmed
and you wish to use the AL-DTM to assign a LockID number
to existing locks, or if LockID numbers are to be changed.
Otherwise set Door Select Mode to "OFF". Press the green
button to select and exit this option.
6. Additional configuration and diagnostic options display in turn
LANGUAGE = ENGLISH
<BACK NEXT> EXIT
DOOR SELECT = ON
ON OFF EXIT
CONFIG. LANGUAGE
Configure the AL-DTM
CLOCK TEST.
LCD DIS. TEST.
LOW BAT. TEST.
FLASH MEM. TEST.
EXIT TO STANDBY
UNCONDITIONAL
FLASH ERASE
SLEEP THEN
POWER DOWN
Hold Down
to Shutdown
AL-DTM
Operation Mode
DTM-III MODE= ON
ON OFF EXIT
PC COMM MODE
. . . .
Entering
Config/Test Mode
(Release buttons
when displayed)