User manual

CHAPTER 4: GENERAL INFORMATION AND FEATURES
4.7 Configuration Profile Set-Up
The Network Series Modem have various operating modes. To save your
energy, it provides 10 sets of factory default settings as well as 10 sets of user setup
profile which store data even the power is off. Users may choose the most similar
factory default setting; make some modifications with front panel or by AT commands
from terminal then save the modified setting to a user profile. From then on, once the
modem is turned on, it will use this user profile as default.
You may find the “Load”, ”Save” selections in the “PROFILE” Menu where you can
save the current configuration into the selected user profile or load the user or the
factory profile.
Table 4.7.1 shows the default settings of each factory profiles.
Table 4.7.1 Factory Profile Default Settings
Profile # #0 #1 #2 #3 #4 #5 #6 #7 #8 #9
SETTING
ITEM
ASY-DL-
AT-
AUTO
ASY-DL-
AT-
NONE
SYN-DL-
V25-
NONE
ASY-2L-
ANS-V34
ASY-2L-
ORG-V34
SYN-2L-
ANS-V34
SYN-2L-
ORG-V34
SYN-4L-
ANS-V34
SYN-4L-
ORG-V34
ASY-2L-
ANS-
Auto
DATA
FORMAT
ASYNC ASYNC SYNC ASYNC ASYNC SYNC SYNC SYNC SYNC ASYNC
COMMAND AT AT V25bis DUMB DUMB DUMB DUMB DUMB DUMB DUMB
LINE Type DIAL DIAL DIAL 2WL.L 2WL.L 2WL.L 2WL.L 4WL.L 4WL.L 2WL.L
RING Times 1 1 1 1 1 1 1 1 1 1
MODEM
SPD
V.34
Adapt
V.34
Adapt
V.34
Adapt
V.34 288 V.34 288 V.34 288 V.34 288 V.34 288 V.34 288 V.34 288
ORG/ANS ANS ANS ANS ANS ORG ANS ORG ANS ORG ANS
Tx level -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm -13dBm
Auto Retrain On On On On On On On On On On
DTE Speed 57600 57600 57600 57600 57600 57600 57600 57600 57600 57600
PROTOCOL V42bis Direct Direct Direct Direct Direct Direct Direct Direct V42 bis
FLOW
CTRL.
RTS/CTS Xon/Xoff Off Off Off Off Off Off Off RTS/CTS
RTS CTRL. ON ON Normal ON ON Normal Normal Normal Normal Normal
DCD CTRL Normal ON Normal Normal Normal Normal Normal Normal Normal Normal
DTR OFF ON ON DISCNT ON ON ON ON ON ON ON
DSR CTRL. ON ON Normal ON ON ON ON ON ON ON
Disconnect
Method
clear
down
immediate clear
down
clear
down
clear
down
clear
down
clear
down
clear
down
clear
down
clear
down
4.8 Remote Access
For improving service loading, the modem offers a remote access function through
secondry channel. It can read and write the parameter of the remote site modem from
local site for well maintenance purpose.
To use this function, the "Remote Access" under "CONFIG MODEM" menu must set
to be on.
4.9 Multi-standard Handshake
The modem complys with ITU-T recommendations V.34, V.32bis, V.32, V.22bis,
V.22, V.21, V.8, V.42 and V.42bis operating standard.
This functions in both calling and answering mode to automatically recognize the
remote modem standard and connect to it accordingly.
41