ORDER NO. CRT5370 DEH-X36UI/XNUC CD RDS RECEIVER DEH-X36UI /XNUC DEH-X3600UI DEH-X3650UI DEH-X3650UI DEH-X3650UI DEH-X3690UI /XNUC /XNCS /XNGS /XNGS1 /XNID This service manual should be used together with the following manual(s): Model No. CX-3287 Order No. CRT4759 Mech. Module S11.6STD Remarks CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly PIONEER CORPORATION 1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan PIONEER ELECTRONICS (USA) INC. P.O.
1 2 3 4 SAFETY INFORMATION CAUTION This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
5 6 7 8 CAUTION A Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Discord used batteries according to the manufacturer's instructions.
1 2 3 4 CONTENTS SAFETY INFORMATION..................................................................................................................................... 2 1. SERVICE PRECAUTIONS ............................................................................................................................... 5 1.1 SERVICE PRECAUTIONS ........................................................................................................................ 5 1.2 NOTES ON SOLDERING ..............
6 7 8 1. SERVICE PRECAUTIONS 1.1 SERVICE PRECAUTIONS A 1. You should conform to the regulations governing the product (safety, radio and noise, and other regulations), and should keep the safety during servicing by following the safety instructions described in this manual. 2. Before disassembling the unit, be sure to turn off the power. Unplugging and plugging the connectors during power-on mode may damage the ICs inside the unit. 3.
1 2 3 4 2. SPECIFICATIONS 2.1 SPECIFICATIONS DEH-X36UI/XNUC, DEH-X3600UI/XNUC A General Signal-to-noise ratio ......... 94 dB (1 kHz) (IHF-A network) Number of channels ........ 2 (stereo) MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3 WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) WAV signal format ........... Linear PCM & MS ADPCM (Non-compressed) Power source ...................14.4 V DC (10.8 V to 15.1 V allowable) Grounding system ............
5 6 7 8 DEH-X3650UI/XNCS A General Number of channels ........ 2 (stereo) MP3 decoding format ...... MPEG-1 & 2 Audio Layer 3 WMA decoding format ..... Ver. 7, 7.1, 8, 9, 10, 11, 12 (2 ch audio) (Windows Media Player) WAV signal format ........... Linear PCM & MS ADPCM (Non-compressed) Rated power source .........14.4 V DC (allowable voltage range: 12.0 V to 14.4 V DC) Grounding system ............Negative type Maximum current consumption ..................................10.0 A Backup current......
1 2 3 4 DEH-X3650UI/XNGS, DEH-X3650UI/XNGS1 A General WAV signal format ........... Linear PCM & MS ADPCM (Non-compressed) Rated power source .........14.4 V DC (allowable voltage range: 12.0 V to 14.4 V DC) Grounding system ............Negative type Maximum current consumption ..................................10.0 A Backup current.................. 4.0 mA or less Dimensions (W × H × D): DIN Chassis ............................ 178 mm × 50 mm × 165 mm Nose ................................
5 6 7 8 DEH-X3690UI/XNID General Rated power source .........14.4 V DC (allowable voltage range: 12.0 V to 14.4 V DC) Grounding system ............Negative type Maximum current consumption ..................................10.0 A Backup current.................. 4.0 mA or less Dimensions (W × H × D): DIN Chassis ............................ 178 mm × 50 mm × 165 mm Nose ................................ 188 mm × 58 mm × 15 mm D Chassis ............................ 178 mm × 50 mm × 165 mm Nose ...........
1 2 3 4 3. BASIC ITEMS FOR SERVICE 3.1 CHECK POINTS AFTER SERVICING A To keep the product quality after servicing, please confirm following check points. No. 1 4 Procedures Confirm whether the customer complain has been solved. If the customer complain occurs with the specific media, use it for the operation check. Play back a CD. (Track search) Check FM/AM tuner action. (Seek, Preset) Switch band to check both FM and AM. Check whether no disc is inside the product.
5 6 7 8 3.3 JIGS LIST - Jigs List Name 16P FFC Test Disc L.P.F. A Jig No. GGD1310 TCD-782 Remarks Tuner Amp Unit - CD Core Unit Checking the grating Checking the grating (Two pieces) Grease No. GEM1024 GEM1043 Remarks CD Mechanism Module CD Mechanism Module - Grease List Name Grease Grease B C 3.
1 2 3 4 4. BLOCK DIAGRAM A ANTENNA A TUNER AMP UNIT JA401 DACOUTL 1 5 16 2,3 18 57 FMMIXIN1 A :DEH-X3 B :DEH-X3 C :DEH-X3 E :DEH-X3 F :DEH-X3 G :DEH-X3 PINDIN LNAIN FM/AM TUNER IC401 TDA7706 I2CSCL I2CSDA RSTN 34 93 33 94 31 88 TUN_SCL RESET IC671 S-80827CNMC-B8M TUN_SDA TUNRES B 39 RES 1 VDD OUT 2 VDD3.
5 6 7 8 A ELECTRONIC VOLUME/ SOURCE SELECTOR IC201 PM9013A A :DEH-X36UI/XNUC B :DEH-X3600UI/XNUC C :DEH-X3650UI/XNCS E :DEH-X3650UI/XNGS F :DEH-X3650UI/XNGS1 G :DEH-X3690UI/XNID JA251 PL 35 OUTPL INAN1L PL 3 PREOUT 40 TUNL RCAG 1 FL FL 6 RCAG 4 Q251 P251 Q252 B 3.3V EVOL_LRCK EVOL_BCK EVOL_DATA EVOL_DT EVOL_CK EVOL_CS EVOL_RST 81 19 104 20 103 21 106 22 110 23 108 24 111 25 87 26 AUXL 37 JA901 MCLK LRCLK FUSE 10A 18 17 15 B.UP B.
1 2 3 4 5. DIAGNOSIS 5.1 OPERATIONAL FLOWCHART A Power ON Vcc : Pin 12, 20, 43, 78, 86, 109 PVcc : Pin 3, 16, 28, 36, 48, 69, 82,101, 112 Vcc = 1.2 V PVcc = 3.3 V BSENS B Pin 90 BSENS = L ASENS Pin 89 ASENS = L DSENS Pin 34 C DSENS = L Starts communication with Grille microcomputer. D 300 ms SWVDD <- H Pin 113 300 ms Source keys operative In case of the above signal, the communication with Grille microcomputer may fail.
5 6 7 8 5.2 ERROR CODE LIST ERROR CODES If a CD memory device is inoperable, or operation of such media is stopped by an error, the error mode is established and a cause of the error is displayed by an error code. Indication of error codes is intended to reduce the number of calls from customers and facilitate failure analysis and repair work in servicing.
1 A 2 Symptoms are written in bold and causes in regular, non-indented text. Regular, indented text is used to indicate actions to be taken. 4 USB storage device/iPod FORMAT READ Sometimes there is a delay between the start of playback and when you start to hear any sound. Wait until the message disappears and you hear sound. Common AMP ERROR B 3 This unit fails to operate or the speaker connection is incorrect; the protective circuit is activated. Check the speaker connection.
5 6 7 ERROR-19 MAINTENANCE Communication failed. Perform one of the following operations. –Turn the ignition switch OFF and back ON. –Disconnect the USB storage device. –Change to a different source. Then, return to the USB source. Pandora system is undergoing maintenance. Try again later. SKIP LIMIT iPod failure. Disconnect the cable from the iPod. Once the iPod’s main menu is displayed, reconnect the iPod and reset it. CHECK APP 8 A Skip limit reached. Do not exceed the skip limit.
1 2 3 4 5.3 CONNECTOR FUNCTION DESCRIPTION A B WIRED REMOTE CONTROL ANTENNA INPUT 15 13 11 9 7 5 3 1 FRONT OUTPUT 16 14 12 10 8 6 4 2 C 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 FL+ FR+ FLFRRL+ RR+ RLRR- REAR OUTPUT or SUBWOOFER OUTPUT NC NC NC NC ACC B.REM B.
5 6 7 8 6. SERVICE MODE 6.1 DISPLAY TEST MODE 1 A [How to enter Test mode] Press and hold "MIX" and "LIST" buttons together, and turn BUP and ACC on. SOURCE LIST MIX B BAND ROTARY Grille condition Conf. item All light up All light off Conf. LCD pattern 1 (* And change ILM color) Conf.
1 2 3 4 6.2 DISPLAY TEST MODE 2 A The information such as the system microcomputer version is checked. [How to enter Test mode] Press and hold "1" and "3" buttons together, and turn BUP and ACC on. [Operation key] Operation key Processing 1+3 Enter display test mode Switch to next test mode Remarks B [Test items] Start display test mode. Press and hold "1" and "3" buttons together, and turn BUP and ACC on.
5 6 7 8 6.3 SOFTWARE VERSION UP METHOD Overview This mode is used for upgrading the MCU software of system using USB memory. A How to enter in USB rewriting mode Press and hold "1" and "2" buttons together, and turn BUP and ACC on.
1 2 3 4 6.4 CD TEST MODE - Flow Chart A To enter the test mode: [4] + [6] -> BUP + ACC ON [Key] [CD] or [SOURCE] Source ON TRK Contents MIN Display [BAND] [2] RF AMP *1 Gain switching TRK MIN SEC Power On (T.Offset is adjusted) TRK MIN SEC 00 B [BAND] MIN SEC [BAND] 91 91 SEC TRK MIN *2 TRK MIN SEC 0X 0X 0X [BAND] TRK MIN SEC [>] Tracking Servo Close 00 00 00 or 99 99 99 [3] SEC [1] Power Off GG ?? ?? ?? [3] F,T,RF AGC*5 F.
5 6 7 8 7. DISASSEMBLY While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same. A - Removing the Panel Assy (Fig.1) 1 1 Release the two latches. 2 Release the two latches and then remove the Panel Assy. 1 2 2 Panel Assy B Fig.1 - Removing the CD Mechanism Module (Fig.2) 1 Remove the screw. 2 Remove the two screws. 1 2 The CD Mechanism Module side is made a bottom.
1 A 2 3 4 - Removing the Tuner Amp Unit (Fig.3) Tuner Amp Unit 1 Remove the two screws. 2 Remove the two screws and then remove the Tuner Amp Unit. 2 B 2 1 1 C Fig.3 - Attention of removing (Fig.4) D Don’t remove this screws excluding the dismantlement of the CD Mechanism Module. E CD Mechanism Module F Fig.
5 6 7 8 - Disassembling the Panel Part (Fig.5, 6) A 1. Remove the arm while bending the rib of the panel upward. B Fig.5 2. Press the upside hook and the bottom side hook of the button at the same time, and pull out the button. C Fig.6 - Assembling the Panel Part (Fig.7, 8, 9) 1. Attach the button from the front side of the panel. D E Fig.7 2. Attach the spring to the arm as shown in the figure. The bended tip of the spring is set to this side. F Hitch the spring to the groove.
1 2 3 4 3. Fit the spring in the groove at the position shown in the figure. A 4. Fit the boss on the lower side of the arm in the lower hole of the panel, and then warp the rib on the panel in the direction shown in the figure and fit the boss of the arm in the panel. B Fig.
5 6 7 8 How to carry the mecha unit A 1. Hold the designated points (shown with dashed lines) of the upper chassis and the front/rear bracket. 2. Be careful not to hold the solid line portions or the CRG mecha part or insert foreign substances, to prevent distortion. 3. When holding the sides of the upper chassis, do not apply excessive force to prevent distortion. (Approx.
1 2 3 4 How to remove the PU unit A 1. Create an empty-clamp state according to “How to create empty clamp state (motor drive)”. 2. Hook the feeding screw biasing spring to a tentative hooking portion (Fig 2b). Be careful not to get injured by the spring edge. 3. Hold the PU at the position A as shown in Fig 1. Slide the PU as far as possible toward the holder in the feeding screw so that a joint on the outer end of the feeding screw is loosened. 4.
5 6 7 8 8. EACH SETTING AND ADJUSTMENT 8.1 CD ADJUSTMENT A 1) Cautions on adjustments In this product the single voltage (3.3 V) is used for the regulator. The reference voltage is the REFO1 (1.65 V) instead of the GND. If you should mistakenly short the REFO1 with the GND during adjustment, accurate voltage will not be obtained, and the servo’s misoperation will apply excessive shock to the pickup. To avoid such problems: a.
1 2 3 4 8.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT A Note : The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the PU unit must be changed, the grating should be checked using the procedure below.
5 6 Grating waveform 7 8 Ech -> Xch 20 mV/div, AC Fch -> Ych 20 mV/div, AC 0 degrees A 30 degrees B 45 degrees 60 degrees C D 75 degrees 90 degrees E F DEH-X36UI/XNUC 5 6 7 8 31
1 2 3 4 8.3 PCL OUTPUT CONFIRMATION A - PCL Output In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled), shift the TESTIN IC601(Pin 99) terminal to H. The clock signal is output from the PCL terminal IC601(Pin115). The frequency of the clock signal is 600 kHz that is divided by 20th of the oscillation frequency of X601 (12MHz). The clock signal should be 600 kHz(- 25 Hz, + 25 Hz).
5 6 7 8 9. EXPLODED VIEWS AND PARTS LIST NOTES : Parts marked by " * " are generally unavailable because they are not in our Master Spare Parts List. The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screw adjacent to mark on the product are used for disassembly. For the applying amount of lubricants or glue, follow the instructions in this manual.
1 2 3 4 9.
5 6 7 8 (1) PACKING SECTION PARTS LIST Mark No. Description Mark No. Part No. Part No.
1 2 3 4 9.
5 6 7 8 (1) EXTERIOR SECTION PARTS LIST Mark No. > Description Mark No. Part No. Description Part No.
1 2 3 4 9.
5 6 7 8 CD MECHANISM MODULE SECTION PARTS LIST Mark No. Description Mark No. Part No. Description Part No. 50 Damper CNW1198 CBA1835 51 Arm CNW1726 Washer CBF1038 52 Motor Unit(M2)(LOAD/CRG) CXC4026 Spring CBH3010 53 Screw Unit CXC8894 54 Arm Assy CXE6232 55 Washer CBF1037 CBF1038 1 .....
1 2 3 4 10. SCHEMATIC DIAGRAM 10.1 TUNER AMP UNIT (GUIDE PAGE) A Note: When ordering service parts, be sure to refer to " EXPLODED VIEWS AND PARTS LIST" or "ELECTRICAL PARTS LIST".
5 6 7 8 A A-b 10u 22k C258 R258 100p/50 100p/50 22k R257 C257 1 Q252 5 4 C261 0.01u/10 NM C260 C259 100p/50 100p/50 0.1u/10 22k R254 R253 C254 RN1910 3 6 C334 NM C319 100p/50 1p/50 C320 C321 C326 C325 C324 13 14 15 16 17 18 19 20 21 22 23 24 25 No connection 1000p/50 10p/50 10p/50 10p/50 10p/50 ACC 10 9 RL2 RL1 FR2 FL2 FR1 FL1 RFGND FUSE YEK5001 8 7 TEL RRRL- 6 RR+ 5 RL+ 4 FR- 3 FL- 2 FR+ 1 FL+ C930 NM RFGND GND FM:+20.3 dBs AM:+20.
VDD 9 GND 10 NM C702 GND DGND1 C 5 K 6 8 C 3 7 M NM C703 L701 NM C620 PVcc 69 QSPCLK 0.1u/10 0 11 DATA DATA 150 R715 R685 DGND 14 GND R618 47k 22k NM R619 NM 47k 47k AVref AVcc AVss C710 X602 CSS1603- 1 2 47 Vss 46 Vss PVcc 48 DM 49 DP 50 ASEMD 51 CDSKIP 52 ROT0 53 ROT1 54 KEYAD 56 VDSENS 55 MODELAD 57 58 59 60 3 16.9344MHz NM L681 R723 NM R722 NM R721 NM 10p/50 C706 10p/50 10p/50 C705 C704 100k GND C202 C206 2.
RGBDT/DIMMER CTF1713- L801 3 3 2 2 CPRST 47 41 38 PVcc 36 CKIO 37 Vss RES 39 Vss 40 PLLVcc NMI 42 Vcc 43 EXTAL 44 XTAL 45 Vss 46 Vss PVcc 48 DM 49 2.2k R817 2.2k GND 2.2k 2.2k 0.1u/10 C610 GND 100k NM R671 DM DP AUXR AUXG AUXL SSENS SWVDD NM ROT1 ROT0 KYDT RGBCK/ILMCLR1 L851 1.5k R613 D671 RGBST/ILMCLR2 NM 0.1u/10 DSENS1 R608 C606 R611 C609 0.
KN2 C410 *1 33p/50 RFGND 2 RFGND L405 68n C466 L407 0.27u CTF1389 C419 15p/50 L406 1u/10 1 GND (W/R) (RMIC) NM JA892 2 MIC1N 5 GND 3 6 BTTOSYS GND 7 SYSTOBT 4 8 MIC1P 9 GND NRST_CPU 6 5 4 3 2 1 BTLRCK 10 BTBCK 11 BTDATA 12 GND 13 GND 14 VCC 15 VCC 16 NM CN971 R976 C973 47p/50 GND C462 GND R973 NM L971 MIC1P MIC1N C974 NM TCAM2 VCCVCO LF1 LFREF *1 NM 0.
0.1u/10 C531 R531 4 3 PAD 9 5 6 7 8 C893 NC3 SCL RST 100 100 R537 R538 USB5V GND CKS6437- NM R539 NM R540 L551 CTH1524- JA891 1 3 2 GND DGND NM : No Mount The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. C892 0.
NM 46 1 B 2 3 B R G B S29 4 2 1 3 CSG1155- 1 LIST S1836 CSG1155CSG1155- 6 4 S1839 S1840 4 2 4 2 4 2 3 1 3 1 3 CSG1155CSG1155- 1 3 1 SOURCE DGND IC1941 PNJ4833M REMOTE 100 R G F DEH-X36UI/XNUC 4 DGND B R 12 S28 36 2 3 13 35 SEG29 4 1 VFS SEG28 2 3 2 AO2 CSG1155- 4 5 RIGHT 4 P02 KST2 S1835 14 1 VSS 2 3 3 IC1851 4 1 1 AO1 2 3 2 1 3 4 1 5 10k NM R1810 D1801 2 3 2 2 3 HN1C01FU(YGR) 0.
5 6 7 8 KDT3 A B REFERENEC AREA MAP S1824 4 2 3 1 GRILLE uCON & LCD KEY MATRIX&ROTARY RGB USB AUX CONNECTOR REMOTE CSG1155- BAND S1832 4 2 3 1 KEYBOARD UNIT :1801-1820 :1821-1850 :1851-1910 :1911-1920 :1921-1930 :1931-1940 :1941-1950 SOURCE CSG1155- KYDT BACK 1 CSG1155- B NM 2 3 D1932 4 NM D1931 DPDT S1837 5 DGND DGND 2 NM 27k S1830 5 R1825 R1824 SWVDD CN1931 CKS6451 3 DGND 1 4 ILMGND L1931 CSD1168-A DGND NM MULTI-CONTROL ILM+B R1851 R1931 R1852 2.2k 2.
1 2 3 4 10.3 CD CORE UNIT (S11.6VA) PU UNIT(P11)(SERVICE) CXX4754 2.4 2.7 (1/10W) PUEN 4.7u/6.3 (2125) Q102 LTA123JUB R111 R110 LD1 Q101 VR LD LD_CURRENT LD AC TOM HOLOGRAM UNIT FOM FOP FOCUS ACT TOP TRK ACT 11 10 10 9 9 8 8 7 7 6 6 5 5 4 4 3 3 2 2 1 1 1M NM PD NM 11 EFM C PD 76 C221 V+3A f E A TOM C220 FOM 0.1u/10 TOP 1u/10 (1608) C204 E F B A TOP FOP FOM TOM CKS4808-A 79 C219 81 0.
5 6 7 8 PUEN LD_CURRENT 12k 12k R303 PUEN SKIP /CDSRQ TEMP 93 95 96 97 98 99 ADENA IO.GND1 TEO C.GND C.Vdd NM NM LOEJ 40 CLCONT 39 CONT R264 38 1k DSCSNS 37 R245 100k R253 8SNS NM C R254 35 HOME EJSW 100k R240 47k /CDSTBY ICECK ICECK R297 C211 NM 0.1u/10 29 R237 28 C233 27 0.01u/16 C210 26 RESET 220 R232 0.1u/10 XTAL X.
1 2 3 4 10.4 WAVEFORMS - CD CORE UNIT(S11.6VA) A 1DSCSNS 3HOME 4LOEJ 5 V/div 5 V/div 5 V/div 500 ms/div Note : 1. The encircled numbers denote measuring points in the circuit diagram. 2. Reference voltage REFO1(1.65 V) 1DSCSNS 5CLCONT 4LOEJ 6VD1 5 V/div 5 V/div 5 V/div 10 V/div 12 cm CD Loading operation 12 cm CD Loading operation Ref.: GND Ref.
5 fRFAGC cTE 9TIN 6 1 V/div 500 mV/div 500 mV/div 2 ms/div fRFAGC cTE 8CIN 7SIN 7 1 V/div 200 ms/div 1 V/div 500 mV/div 2 V/div 8 gLRCK 2 V/div hBCLK 2 V/div iDOUT(DATA) 2 V/div 32 Tracks Jump waveform (Zoom of 100 Track Jump waveform) Search operation(Outter to Inner) Digital Out waveform Ref.: REFO Ref.: REFO Ref.
1 2 3 4 11. PCB CONNECTION DIAGRAM 11.1 TUNER AMP UNIT TUNER AMP UNIT 150 W.REM JA891 PREOUT 140 6 SIDE A Chip Part P.C.Board SIDE B R259 C254 R254 P251 130 Q251 3 VA891 C891 3 2 1 4 1 R891 5 R892 6 C894 VA892 3 R893 R255 1 C252 5 C893 Q252 1 2 C260 1 2 C328 C319 C320 C331 C301 C318 C251 R555 C562 C551 C556 120 C557 C563 C558 C555 C570 1 C565 C554 R551 C553 110 C564 R553 R552 R554 1 C552 D552 L551 100 C > P 251 (A,6,130) Fuse 3.
5 6 7 8 A SIDE A C326 POWER SUPPLY 25 C325 R312 3 5 7 9 11 13 15 1 18 17 Q752 D902 C323 C324 JA401 C421 P402 P401 R406 C422 L401 C453 60 55 50 L414 C448 R416 L415 C417 C404 C413 L403 C403 R415 L417 C419 R413 D912 D911 1 R879 E Q874 R873 L601 R621 D R871 L602 R609 R872 R659 R670 C449 L418 C445 R620 R664 E R660 C914 15 Q871 C871 R604 C414 C416 C412 C438 Q872 E R876 R603 R662 CN971 C616 C617 C605 R616 C614 C615 C971 1 X401 Q873 D671 R671 R6
1 A A 2 3 4 TUNER AMP UNIT 1 B 1 C TESTIN PCL D 1 1 E 1 F 160 A 54 150 140 130 120 110 100 90 DEH-X36UI/XNUC 1 2 3 4 80
5 6 7 8 SIDE B A 150 1 140 1 1 130 B 120 110 100 C 90 80 70 D 60 50 40 E 30 20 10 Y 80 70 60 50 40 30 20 10 X F 0 A DEH-X36UI/XNUC 5 6 7 8 55
40 30 20 X 0 Y R1866 10 20 R1857 40 30 BACK S1832 MULTI-CONTROL BAND S1824 R1825 R1824 Q1859 R1867 10 10 R1855 D1883 IC1851 C1870 R1854 R1858 Q1858 D1882 Q1853 C1855 C1854 R1865 Y 0 20 50 LEFT S1821 R1861 R1860 D1931 D1886 60 1 5 10 15 20 25 30 35 40 45 50 130 1 35 V1802 2 S1838 40 SEGMENT LCD 30 3 S1839 45 65 S1837 60 S1836 5 120 4 110 25 S1840 100 20 DISP S1834 90 55 80 RIGHT S1823 15 50 70 X1801 Q1857 R1864 X MIX S1826 C1805 C1804
5 6 7 8 A B C D E F DEH-X36UI/XNUC 5 6 7 8 57
1 2 3 4 11.3 CD CORE UNIT (S11.6VA) C CD CORE UNIT(S11.
5 7 8 CD CORE UNIT(S11.
1 2 3 4 12. ELECTRICAL PARTS LIST A B NOTE: Parts whose parts numbers are omitted are subject to being not supplied. The part numbers shown below indicate chip components. Chip Resistor RS1/_S___J,RS1/__S___J Chip Capacitor (except for CQS.....) CKS....., CCS....., CSZS..... The > mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation.
5 6 Circuit Symbol and No. L L L L 403 404 405 406 (A,151,102) (A,146,102) (A,151,108) (A,148,105) Inductor Inductor Inductor(A,B,C) Inductor(A,B,C) CTF1786 CTF1786 LCYB68NJ1608 CTF1389 L 407 L 408 (A,147,107) (A,141,104) (A,141,104) (A,143,109) Chip Coil(E,F,G) Inductor(A,B,C) Inductor(E,F,G) Chip Coil(E,F,G) LCTAWR27J2520 LCTC4R7K1608 LCTC1R5K1608 LCTAWR39J2520 L 409 L 410 Circuit Symbol and No.
1 Circuit Symbol and No. A B 2 3 Part No. Circuit Symbol and No.
5 6 Circuit Symbol and No.
1 2 Circuit Symbol and No. C 969 A (A,135,113) 10 uF 3 Part No.
5 Circuit Symbol and No. 6 Part No.
