Owner's manual

Page 2 DEU/TS - fs 059 659d Page 3
Draft, CopyDraft, Sans Serif LQ and OCRB will be handled in the
same way like MT50D OCRB. The selected Font in the menu is
choosen. E.g. recognizing the OCRB sequence “ESC(?” leads
automatically to the selected font. Getting OCRA sequence leads
always to OCRA font. Is the setting any NLQ font, the printout will
be performed in OCRA NLQ. This is also valid for LQ quality. It is
recommended only to use LQ OCR due to better legibility.
The implemented character sets correspond to the MT50 sets. Natio-
nal characters form 80
hex
to BF
hex
will match MT50D sets.
Factor MT 50 this printer/emulation
with without
descenders
3 times 60 60 48
5 times 90 80 72
7 times 120 120 120
The LCP character frame (reserved space)
however is identical to MT50D


back
next
Print Menu Reset Quiet Font CPI LPI Skip
VT-Code Emulate
BiDir I/O
Country SlZero
AutoCR AutoLF
Wrap LineAdvMenLock LanguagePaper AutoCut
Width ColorOpt
Bit8Mode
Matr357 Barmode
FFMode
ParameterGroup Parameter Description
VT-Code VerTab * set printer handling of control code VT (0B
hex
). The
LF+Cut VT print the line buffer, create a CR, move to next
FF+Cut vertical tab, or LF or FF and Cut will be added.
Emulate MT-Standard *
MT-Ansi
I/O Protocol and Special only with serial interface available
Protocol XON/XOFF * If ENQ/STX or ETX/ACK is selected, the XON/
ENQ/STX XOFF protocol is additionally working.
Robust XON-XOFF There is no XON/XOFF protocol by using the
ETX/ACK ACK/NAK protocol.
ACK/NAK
Special Only available if serial interface is assembled and one of following
protocols is selected: ENQ/STX, ETX/ACK or ACK/NAK
ErrMode=On substitute wrong character with „ ? “
ErrMode=Off * delete the whole block at fault
Blockend=On ETX, DEL, LF, FF, CR, VT
Blockend=Off * ETX, DEL
Status=On * printer sends status byte on ENQ
Status=Off no status byte on ENQ
Delete=DEL * delete at DEL
=ENQ delete at ENQ
=Del+ENQ delete at DEL and ENQ
=DEL>Reset DEL clean printer buffer
=No no delete function
Remote=On Offline and paperend switch DTR, RTS and RDY
Remote=Off * no level response to DTR, RTS and RDY
LineAdv CR, LF * CR active, LF active
LF LF active, CR ignored
CR CR active, LF ignored
Bit8Mode Char * change Bit 8 for next character
Line change Bit 8 for complete line
Matr357 LCP * 3-, 5- or 7-times expansion uses LCP font or
Matrix current matrix font
Menue Structure
Fonts
LCP Matrix 3-5-7
in x/180 inch
Opposite to original MT 50 the signal CTS is not controlled. It is
possible to gain the state “Offline” and “PaperEnd” monitoring the
DTR, RTS and BUSY line, the parameter REMOTE must be set to
ON. Transparent ESC sequences will be ignored. Additionally the
ETX/ACK protocol is implemented. Using ACK/NAK protocol the
data buffer should be set to maximum. The meaning of the ENQ
character can be choosen in the setup menu (Status Request and/or
Delete Function is only valid in ACK/NAK protocol). The function
“Delete = Del>Reset” in menu leads only to a buffer clear. Also the
block end function can be switched either to ETX or to ETX, LF, VT,
FF and CR. Automatic block clear is programmable. Wrong
characters will be substituted by a “?” then.
Serial Interface