Installation manual

ManualsBrandsDAS ManualsComputer equipmentNX-148E LCD Codepad

Table of Contents

Enterin

the Pro

ram Mode

...............................

Selectin

the Module to Pro

ram

...........................

Pro

rammin

a Location

..................................

NX-148 Library

.........................................

Loadin

Factory Defaults

.................................

Enrollin

Modules and Keypads

............................

Pro

rammin

the NX-148 Keypad

.......................

3 - 5

Adjusting the View

..........................................

Programming Custom Messages

..............................

Set Keypad Options

........................................

Set Keypad Number & Partition

...............................

Keypad Functions

....................................

5 - 7

Reading the Event Log

......................................

Set Elapsed Increments

.....................................

Set System Time & Date

.....................................

Adjust Keypad Tone

........................................

View Zone Status

..........................................

View Alarm Memory

........................................

Change User Codes

........................................

Assigning Authority Level

....................................

Partitioned System Operation

...........................

7 - 9

Service Display

.....................................

9 - 10

Maximum Wire Run

....................................

Specifications & Warranty

..............................

Back

NX-148 LCD KEYPAD

INSTALLATION MANUAL

Summary of content (12 pages)

PAGE 1
NX-148 LCD KEYPAD INSTALLATION MANUAL Table of Contents Entering the Program Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Selecting the Module to Program . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Programming a Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 NX-148 Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Loading Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 2
ENTERING THE PROGRAM MODE To enter the Program Mode, press [U]-[8]. At this time, the LCD screen will prompt you for the programming code. Next, enter the "Go To Program Code" (FACTORY DEFAULT IS [9]-[7]-[1]-[3]). If the "Go To Program Code" is valid, the LCD screen will prompt you for the device address you wish to program. You are now in the Program Mode and ready to select the module to program.
PAGE 3
A B C D E F G a b c d e f g " # $ % & ' ( • H h ) I i U ä J j + K L M N O k l m n o , - .
PAGE 4
[U]-[9]-[2] PROGRAMMING CUSTOM MESSAGES IN THE KEYPAD NOTES: The messages (custom, zone, and shutdown) are transferred to other LCD keypads after this mode is exited. All keypads must be addressed and enrolled for this to happen. Set the keypad numbers with [U]-[9]-[4] prior to programming custom messages. If a keypad is added after messages are programmed, you should either program ALL messages in it, or enter custom message programming on an existing keypad and make changes.
PAGE 5
[U]-[9]-[4] SET KEYPAD NUMBER AND PARTITION The LCD screen will prompt for a code. 1) Enter [U]-[9]-[4] 2) Enter [program code] The LCD will now prompt you for the keypad number followed by [U]. The current keypad number will be displayed in the lower right hand corner. 3) Enter the keypad number followed by [U] The LCD will now prompt you for the partition number followed by [U]. The current partition will be displayed in the lower right hand corner.
PAGE 6
[U]-[0] ADJUST KEYPAD TONE 1) Press [U]-[0] The LCD screen will prompt you to use the scroll keys located on the right of the display to raise or lower the tone. 2) Use the up scroll key to raise the tone. Use the down scroll key to lower the tone. The keypad will emit a continuous tone to allow you to hear the current selection. 3) When the desired tone is reached, press the [#] key to set this tone and exit the mode.
PAGE 7
4) Enter a partition number. Note: The default allows access to all partitions. The first keypress will remove access to the partition. To reestablish access, press the partition number again. When completed, press [U]. The LCD Screen will prompt you for the next user code. 5) If another user code needs to be programmed, return to Step 3. 6) To exit this feature, press [#].
PAGE 8
DISPLAYS IN THE PARTITIONING MASTER MODE Armed and Ready Status The LCD screen will display the Armed and Ready status of ALL eight (8) partitions if any or all of the areas is armed or not ready. Ready Armed 12345678 1234-678 System Ready Type code to arm This display is reflecting all 8 areas are Ready, and Area 5 is disarmed. NOTE: If a number is flashing on the armed line, that area is armed Instant. If a number is flashing on the ready line, that area is ready to be Force Armed.
PAGE 9
Area 5 Ready Type code to arm Area 5 is selected and Area 5 is ready to arm. To exit the individual partition mode, enter [#]-[#]. Silencing Alarms in the Multi-Partition Mode If the keypad is sounding an alarm or the siren is running, it can be silenced by entering a code with the authority for the area(s) that are in alarm. NOTE: The [EXIT], [BYPASS], and Alarm Memory [U]-[3] function keys will only work if an individual partition is selected.
PAGE 10
Expansion Power Trouble The main power to an expansion power supply is not on. Expansion Low Battery An expansion power supply has a low battery. Expander Box Tamper A box containing an expansion device has been opened. Expansion Over-current A short circuit of an expansion device’s power supply has occurred. Expansion Trouble An expansion device or keypad is not reporting to the control panel.
PAGE 11
NX-124 MAXIMUM WIRE RUN (Note: These numbers are for one keypad at the end of the wire. When connecting more than one keypad to the end of the wire, a heavier gauge wire will be required.
PAGE 12
SPECIFICATIONS OPERATING POWER 12 VDC Regulated Supplied by NX-8 or NX-320 OPERATING TEMPERATURE 32 to 120 degrees F CURRENT DRAW 110 mA Maximum 75 mA without Sounder LCD KEYPAD DIMENSIONS 6.4" Wide 5.3" High 1.0" Deep SHIPPING WEIGHT 2 lbs. FIVE YEAR LIMITED WARRANTY CADDX CONTROLS, INC. GUARANTEES THIS PRODUCT AGAINST DEFECTIVE PARTS AND WORKMANSHIP FOR TWENTY-FOUR (24) MONTHS FROM DATE OF MANUFACTURING. IF ANY DEFECT APPEARS DURING THE WARRANTY PERIOD, RETURN IT TO CADDX POSTAGE PREPAID.