User manual

Chapter 4 Connecting Signals
NI 6034E/6035E/6036E User Manual 4-6 ni.com
Analog Input Signal Overview
The analog input signals for the NI 6034E/6035E/6036E device are
ACH<0..15>, ASENSE, and AIGND. Connection of these analog input
signals to your device depends on the type of input signal source and the
configuration of the analog input channels you are using. This section
provides an overview of the different types of signal sources and analog
input configuration modes. More specific signal connection information is
provided in the Connecting Your Analog Input Signals section.
VCC DO 0.1 Short-circuit
to ground
1A fused
DIO<0..7> DIO V
cc
+0.5 13 at (V
cc
0.4) 24 at
0.4
1.1 50 kpu
SCANCLK DO 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
EXTSTROBE* DO 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI0/TRIG1 DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI1/TRIG2 DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI2/CONVERT* DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI3/GPCTR1_SOURCE DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI4/GPCTR1_GATE DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
GPCTR1_OUT DO 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI5/UPDATE* DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI6/WFTRIG DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI7/STARTSCAN DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI8/GPCTR0_SOURCE DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
PFI9/GPCTR0_GATE DIO V
cc
+0.5 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
GPCTR0_OUT DO 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
FREQ_OUT DO 3.5 at (V
cc
0.4) 5at0.4 1.5 50 kpu
AI = Analog Input DIO = Digital Input/Output pu = pullup
AO = Analog Output DO = Digital Output
The tolerance on the 50 kpullup resistors is very large. Actual value may range between 17 and 100 k.
Table 4-2. I/O Signal Summary for the NI 6034E/6035E/6036E (Continued)
Signal Name
Signal
Type and
Direction
Impedance
Input/
Output
Protection
(Volts)
On/Off
Source
(mA at V)
Sink
(mA
at V)
Rise
Time
(ns)
Bias
UM.book Page 6 Monday, May 14, 2001 10:32 AM