MANUAL ENGLISH GIG-124C Order code: D2284 Highlite International B.V.
GIG-124C Table of contents Warning ...............................................................................................................................................................................2 Unpacking Instructions .................................................................................................................................................2 Safety Instructions .............................................................................................................
GIG-124C Warning FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
GIG-124C Never use anything to cover the ground contact. Never leave any cables lying around. Do not insert objects into air vents. Do not connect this system to a dimmer pack. Do not switch the system on and off in short intervals, as this would reduce the system’s life. Do not open the device and do not modify the device. Do not drive the inputs with a signal level bigger, than required to drive the equipment to full output.
GIG-124C Operating Determinations This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. The minimum distance between light-output and the illuminated surface must be more than 0.5 meter. The maximum ambient temperature ta = 45°C must never be exceeded. The relative humidity must not exceed 50 % with an ambient temperature of 35° C.
GIG-124C Description of the device Features Ultra-low noise discrete MIC Preamps with +48V Phantom Power. 4 MIC Input Channels with XLR and balanced Line Input and Insert I/O and Compressor control. Low Cut for each MIC Input. 2 Stereo Input Channels with mono XLR Input and TRS Jack. 2 Stereo Input Channels with RCA Jack and TRS Jack. 3-band EQ and Peak LEDs on each MIC channel. 2-band EQ and Peak LEDs on Stereo channels.
GIG-124C Installation Introduction This is a professional compact mixer that gives you great quality and better reliability than ever before. You will get the smooth, accurate more natural and open sound from this apparatus. It is really ideal for gigs, recording and fixed PA installations.
GIG-124C Control Elements 1. MIC INPUT JACKS (CHs 1 to 7/8) The balanced XLR input connects to microphones, DI boxes and multicores. 2. LINE INPUT JACKS (CHs 1 to 4) This is a ¼" jack connector which connects to line-level signal sources (for example, keyboards, CD players and wireless microphone receivers). The input is balanced (TRS connector) but can also be used with unbalanced connectors (TS connector). 3.
GIG-124C 9. EQUALIZER Hi The high-frequency range is processed with a shelving filter above 12 kHz. You can boost or cut the bands up to 15 dB. When in center position (0 dB), the equalizer has a flat response. MID The HIGH MID control adjusts the mid frequency range. This is a peak filter which boosts and cuts the frequencies centered at 2,5 kHz. You can boost or cut the bands up to 15 dB. When in center position (0 dB), the equalizer has a flat response.
GIG-124C 17. GR1-2 Each channel is equipped with a GR1-2 switch, which allow you to feed multiple channels to a stereo mixdown. The volume level can be adjusted using the GR1-2 LEVEL fader. 18. MAIN Each channel is equipped with a MAIN switch, pressing this button will send the signal to the MAIN MIX bus. 19. LEVEL The channel fader adjusts the level of the channel signal as part of the main mix (or subgroup). 20. MAIN MIX LEVEL Use this high-precision MAIN fader to control the output level of the main mix.
GIG-124C 28. AUX 1 SEND The Master AUX 1 SEND control adjusts the signals volume level of the respective aux send connector. This way you adjust the sum of the AUX signal on the input channels. 29. ST RETURNS TO AUX This control assigns the ST RETURN signal to their respective AUX SEND outputs. 30. ST RETURNS TO MAIN This control assigns the ST RETURN signal to their respective MAIN MIX outputs. 31. PHANTOM LED This LED indicates when the phantom power is switched on for the microphone inputs. 32.
GIG-124C 41. OPTIONAL MODULES SECTION This section can be selected and installed according to the user's requirements. Open the cover and connect the module to connector CN6. The optional modules are: SMP-R, SMP-S, & Bluetooth-2.1. The signal for module playback can be assigned to Main Mix by 2TK routing. When using SMP-R recording function, the Cn12 needs to be connected. The signal comes from the Main Mix.
GIG-124C Modules Option One - SMP-S (Order code: D2290) The file system should be FAT16 or FAT32. This player can only decode MP3. It has 7 rank subordinate folders at most. A USB port: Allows the connection of any USB memory stick. B PRE: Use this button to go back to the beginning of the current track or select a previous track for playing. C NEXT: Use this button to skip to the next track. D PLAY / PAUSE: Use this button to start playback.
GIG-124C D E "Program" mode 1). In Fig. 02, select "Program" to enter into the following interface: "Play list Set ": Set the play list. "Playing List": Play list. Press PRE/ NEXT key to select, press STOP key to return the Fig. 02. 2). After entering into the "Play List Set", the display will show as Fig. 03. Selecting the desired folder, the display will show the following interface. The display will show all the MP3 files, the selected song will be inserted into the play list and a mark will appear.
GIG-124C Option Two - SMP-R (Order code: D2291) The file system of USB memory for USB players is FAT16 and FAT32and these players can only decode MP3. It has 7 rank subordinate folders at most. A USB port: Allows the connection of any USB memory stick. B PRE: Use this button to go back to the beginning of the current track or select a previous track for playing. C NEXT: Use this button to skip to the next track. D RPT: Use this button to repeat one track, one folder or all tracks.
GIG-124C Option Three - Bluetooth Version 2.1 (Order code: D2292) Can be paired with mobile phones, tablets or PC Bluetooth adapters to play stereo audio. A DISPLAY These two LEDs are used to display different working states: 1) For the first time that the module is powered on, it is in stand-by state and the right LED flashes twice about 2 seconds. 2) Matching state, two LED's alternately flash quickly. 3) After connecting the device, the right LED is lighted constantly.
GIG-124C 42. AC INLET WITH FUSE HOLDER Before connecting the unit to the mains, ensure that the voltage setting matches your local voltage. Blown fuses should only be replaced by fuses of the same type and rating. To disconnect the unit from the mains, pull out the main cord plug. 43. POWER ON / OFF Use the POWER switch to turn on the mixing console. The POWER switch should always be in the “Off” position when you are about to connect your unit to the mains. 44.
GIG-124C Connection Cables Take care of your cables, always holding them by the connectors and avoiding knots and twists when coiling them: This gives the advantage of increasing their life and reliability. Periodically check your cables. A great number of problems (faulty contacts, ground hum, discharges, etc.) are caused entirely by using unsuitable or faulty cables.
GIG-124C Block Diagram Order code: D2284 18
GIG-124C Technical Specifications MODEL: Mono channels Microphone input Frequency response Distortion(THD+N) Gain range Max.
GIG-124C Main mix section Max. MAIN MIX output AUX range Fader range PHONES/CONTROL-ROOM range Hum & Noise Crosstalk Power supply Main voltage Fuse Rated power consumption Order code: D2284 +22dBu XLR balanced (+16dBu un-balanced) OFF to +15dB OFF to +10dB OFF to +15dB <-80dB@20Hz~22KHz A-weighted 1 channel & MAIN level:0dB,the other :minimum <-80dB@0dB 20Hz~22KHz A-weighted MAIN level:0dB, the other :minimum, 100-240V~ 50/60Hz T1.
GIG-124C Notes Order code: D2284 21
GIG-124C Dimensions Order code: D2284 22
©2013 DAP Audio
