MANUAL ENGLISH IMIX 5.3 Ordercode: D2352 Highlite International B.V.
IMIX 5.3 Table of contents Warning ...............................................................................................................................................................................2 Unpacking Instructions .................................................................................................................................................2 Safety Instructions .............................................................................................................
IMIX 5.3 Warning FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY BEFORE YOUR INITIAL START-UP! Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
IMIX 5.3 Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never remove warning or informative labels from the unit. Never use anything to cover the ground contact. Never leave any cables lying around. Do not insert objects into air vents. Do not connect this system to a dimmerpack.
IMIX 5.3 Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International L N EU Cable UK Cable US Cable BROWN RED YELLOW/COPPER BLUE BLACK SILVER YELLOW/GREEN GREEN GREEN Make sure that the device is always connected properly to the earth! Pin FASE NUL EARTH Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
IMIX 5.
IMIX 5.3 Rear IEC cable inlet Zone B RCA unbalanced out connector Zone C XLR balanced out connectors Channel 4 line 1/line 2 input connectors Zone B XLR balanced out connectors Channel 3 line 1/line 2 input connectors Zone A XLR balanced out connectors Channel 2 line input connectors Zone C RCA unbalanced out connector Channel 1 line input connectors Zone A RCA unbalanced out connector GND screw Installation Remove all packing materials from the IMIX-5.3.
IMIX 5.3 Functions 1. Mic gain control The input sensitivityof the Mic (2) input is determined by the gain control. With the gain control you are able to adjust the input-sensitivity for an optimal match with the mixer’s internal operation level. The high gain of this mixer is ideal when dealing with very low input levels. 2. Mic input combo connector Electronically balanced combo-type input for connecting low impedance microphones. The input has extremely low noise and low hum.
IMIX 5.3 9. Input selection switch (channel 1/2) With this you are able to assign the line inputs or the phono inputs to the according channel. 10. Peak LED The peak LED shows peak levels in a channel’s incoming signal level. If the red peak LED frequently blinks or constantly lights, the corresponding channel is likely to enter clipping and you have to reduce the input’s amplification using the gain (8) control. The peak LED lights at a level of 8 dB below clipping.
IMIX 5.3 17. Aux mini jack in connector Unbalanced stereo mini jack aux input for connecting a line/phones level device. Use the phone/Line (21) button to set up this input for connecting either headphone or line level output devices. 18. Power LED Indicates that the IMIX-5.3 is switched on. 19. Power on/off switch Do not supply power before the whole system is set up and connected properly. 20. Aux RCA in connectors Unbalanced stereo RCA aux input for connecting a line/phones level device.
IMIX 5.3 30. Power adapter connector This is the remote AC power supply input socket for the IMIX-5.3 It is a special three core socket. Please use the supplied DAP audio adapter only. 31. Zone C XLR balanced out connectors Use these outputs to connect an amplifier with balanced inputs. 32. Zone B XLR balanced out connectors Use these outputs to connect an amplifier with balanced inputs. 33. Zone A XLR balanced out connectors Use these outputs to connect an amplifier with balanced inputs. 34.
IMIX 5.3 Set Up and Operation Before plugging the unit in, always make sure that the power supply matches the product specification voltage. Do not attempt to operate a 115V specification product on 230V power, or vice versa. Connection Cables Take care of your cables, always holding them by the connectors and avoiding knots and twists when coiling them: This gives the advantage of increasing their life and reliability. Periodically check your cables.
IMIX 5.3 Troubleshooting DAP Audio IMIX-5.3 This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit operates properly, do not carry out following steps. 1. 2. 3. 4. 5. If the device does not operate properly, unplug the device. Check power from the wall, all cables, connections, etc. If all of the above appears to be O.K., plug the unit in again.
IMIX 5.
IMIX 5.
©2013 DAP Audio
