PROFESSIONAL AUGER SERIES MODELS 615 1025 1530 2035 Hex, Hex, Hex, Hex, 615 Round 1025 Round 1530 Round 2035 Round Owner: Date Purchased: Model #: Serial #: Manual #: DANGER Si no entiende ingles, se prefiere que busque a alguien que interprete las instrucciones para usted. 9MPRO2455212 Operator’s Manual Danuser LLC 500 E. 3rd St. P.O. Box 368 Fulton, MO 65251 Tel: (573) 642-2246 Fax: (573) 642-2240 E-mail: sales@danuser.com Website: www.danuser.
Dear Owner/Operator, Thank you for purchasing this Danuser Hydraulic Earth Auger. We appreciate your business. Your safety as an operator of our product is very important to us. Therefore, before you assemble, install, operate, or maintain your Danuser Earth Auger, read and understand this manual thoroughly. If there is anything you do not understand, immediately contact your dealer, or contact our factory direct. Tel: Fax: E-mail: (573) 642-2246 (573) 642-2240 sales@danuser.
Foreword Please read this manual thoroughly! Before you assemble, install, operate, or maintain your Danuser Earth Auger, read this manual thoroughly. If there is anything you do not understand, immediately contact your dealer, or call our factory direct at (573) 642-2246. Powered equipment can be dangerous if not assembled, installed, operated, or maintained properly.
Safety WARNING Working with unfamiliar equipment can lead to careless injuries. Read and understand this manual and the manual for your vehicle before assembling, installing, operating, or maintaining this earth auger. If there is anything in this manual you do not understand, contact your dealer or Danuser LLC. The safe use of this machine is strictly up to you, the operator.
Safety (continued) • Do not allow riders on the equipment at any time. There is no safe place for any riders. • Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this equipment. Consult your doctor about operating this machine while taking prescription medications. • Consult local utility companies to make certain there are no buried gas lines, electrical cables, etc., in the work area before beginning operation.
Drive Unit Specifications 615 1025 1530 2035 Minimum Hydraulic Flow 6 GPM 10 GPM 15 GPM 20 GPM Maximum Hydraulic Flow 15 GPM 25 GPM 30 GPM 35 GPM Maximum Continuous Operating PSI 3000 PSI 3000 PSI 3000 PSI 3000 PSI Maximum Auger Diameter 24 inches 30 inches 36 inches 36 inches 2” Hex or 2-9/16" Rd. 2” Hex or 2-9/16" Rd. 2” Hex or 2-9/16" Rd. 2" Hex or 2-9/16" Rd. Output Spindle Model 615 PSI 2000 2500 3000 TORQUE 1115 Ft.-Lbs. 1393 Ft.-Lbs. 1672 Ft.-Lbs.
Hydraulic Requirements Filtration Requirements: • A filter of, at least, 25 micron filtration is required. A filter capable of 10 micron filtration is preferred. The majority of paper type filters are 25 microns or better. NOTE The life of the hydraulic motor is almost entirely dependent upon cleanliness of the oil. Instructions in your vehicle operator’s manual regarding filter and oil changes should be carefully followed.
Assembly & Installation Drive unit and auger exploded views and part lists are detailed on separate pages in this manual. Skid-Steer Mount 1 = Safety Sign Location 4 5 9 3 6 2 11 7 8 10 Because of the weight of some components, and because some components are difficult to balance, two people are required for safe assembly and installation of this equipment.
Assembly & Installation Mini-Excavator Mount 5 Drive unit and auger exploded views and part lists are detailed on separate pages in this manual. 7 REF. NO. PART NO. 1 ----2 10219 3 10032 4 1600 5 ----6 10220 7 6196 8 10038 10039 9 10041 10042 Because of the weight of some components, and because some components are difficult to balance, two people are required for safe assembly and installation of this equipment. DESCRIPTION QTY.
Assembly & Installation Drive unit and auger exploded views and part lists are detailed on separate pages in this manual. 7 TLB & Excavator Mount 5 REF. NO. PART NO. 1 ---- 2 10247 3 10032 4 1600 5 ---- 6 10242 7 10243 8 3092 9 10038 10039 10 10041 10042 DESCRIPTION Drive Unit Knuckle Sub-Assembly Pin (1-1/4” x 7-5/8”) Klik Pin Ear Assembly Tube-Clamp Bolt (5/8” 11 x 2”) Nut (5/8” 11) Special Retaining Bolt - 2" Hex (3/4” 10 x 4”, Gr.
Assembly & Installation Drive unit and auger exploded views and part lists are detailed on separate pages in this manual. Bolt-on Bucket Mount 6 7 8 1 5 2 = Safety Sign Location 4 3 REF. NO. 1 9591B 2 10022 3 ----4 10032 5 1600 6 9595 7 3041 8 2805 9 10038 10039 10 10041 10042 9 10 Because of the weight of some components, and because some components are difficult to balance, two people are required for safe assembly and installation of this equipment.
Assembly & Installation (continued) STEP 5: Grease the inside of the auger collar liberally and attach the auger with the retaining bolt and nut that came attached to the drive unit spindle. This is a special thread length bolt - use genuine Danuser replacement parts only. For hex spindle, use Danuser PN 10038 (3/4” 10 x 4”, Gr. 8, 3/4” of thread) special retaining bolt and nut PN 10041. NEVER use a bolt longer than longer than 4". For round spindle, use Danuser PN 10039 (7/8” 9 x 4-1/4”, Gr.
Operation WARNING Read and understand this Operator’s Manual carefully before attempting to operate the Danuser Earth Auger. You are responsible for furnishing this manual to others who may use the unit. If you have any questions regarding the proper assembly, installation, or operation of this earth auger, contact your dealer or Danuser LLC. DANGER Serious injury or death can result from misuse of this equipment.
Operation (continued) STEP 6: The hydraulic flow rate or pressure should not exceed the earth auger’s specified maximums. The hydraulic minimums must be met to deliver satisfactory performance. Use only enough down pressure to assure positive penetration of the auger into the ground. Ease up on down pressure if auger rotation slows down drastically or stalls. Excessive down pressure will cause the auger to frequently stall.
Troubleshooting PROBLEM Slow Speed POSSIBLE CAUSE a) Low flow SOLUTION Check with flow meter. If low, investigate the cause. b) Fittings or connections are too small or incompatible c) Line restrictions d) Dirty oil or oil filter Replace with proper fittings. Clear lines. Change oil and oil filter according to vehicle manufacturer’s recommendation. e) Hydraulic pump worn See your dealer for repairs.
Maintenance DAILY CHECK PLANETARY GEAR OIL LEVEL Check oil level daily to assure proper lubrication is maintained. Check by removing the fill plug - with the drive unit standing vertically. Oil should just cover the visible gear. CHECK FOR CLEAN HYDRAULIC OIL The majority of all hydraulic component failures are caused by contamination of the hydraulic oil. At all times, keep dirt and other contaminates from entering the hydraulic system during connecting and disconnecting the hydraulic system.
Drive Unit Parts 12 2 = Safety Sign Location 11 3 4 1 5 6 7 9 REF. NO. PART NO.
Decals & Safety Signs PART NO. DANUSER101 Locations: Quick Attach Plate, sides Drive Unit, front Model No. & Serial No. Location: Drive Unit, top PART NO. DIG2 Location: Quick Attach Plate, top PART NO. 10984 (615) PART NO. 10985 (1025) PART NO. 10986 (1530) PART NO. 10987 (2035) Location: Drive Unit, front PART NO. 9875 Location: Drive Unit, top PART NO. DIG4 Location: Drive Unit, back PART NO. DIG3 Locations: Drive Unit, sides PART NO. DIG8 Location: Auger WARNING 18 PART NO.
Decals & Safety Signs WARNING Clean or replace all safety signs if they cannot be clearly read and understood. (continued) PART NO. DIG7 Location: Knuckle Ears, sides PART NO. DIG6 Location: Knuckle Ears, sides Mini-Excavator Knuckle TLB & Excavator Knuckle Augers & Accessories = Safety Sign Location AUGER ADAPTERS AUGER COLLAR 2” Hex 2-9/16" Rd. 10328 10329 VARIABLE LENGTH EXTENSIONS LENGTH 12” 24” 48” 72” 2” HEX --10900 10901 10902 2-9/16" RD.
Augers & Accessories (continued) Fishtail Point Dirt Hardfaced Chunky Carbide Nut Bolt 4” diameter auger Dirt Hardfaced Chunky Carbide Nut Bolt 10331 10332 10335 10412 10413 below 10333 10334 10336 10412 10416 Teeth Bolt & Nut Carriage Bolt Nut 10410 10411 “FAB” AUGERS - 4’ Length DIA. NO. OF TEETH 2” HEX 2-9/16" RD.
Augers & Accessories “BULLET” ROCK AUGERS 4’ Length (continued) “Bullet” Rock Pilot Tooth Tooth Holder 10758 10759 10760 DIA. NO. OF TEETH 2” HEX 2-9/16" RD. 4.5” 6” 7” 8” 9” 10” 12” 14” 16” 18” 24” 30” 36” 4 6 8 8 8 10 12 14 16 18 22 24 30 10700 10703 10706 10709 10712 10715 10718 10721 10724 10727 10730 10733 10736 10701 10704 10707 10710 10713 10716 10719 10722 10725 10728 10731 10734 10737 = Safety Sign Location Flat face ISO couplers.
Warranty DANUSER LIMITED WARRANTY Model # Serial # Danuser LLC (“Danuser”) warrants its products, under normal use and maintenance, to be free from defects in material and workmanship for periods specified below from the purchase date from an authorized Danuser Dealer. Start of the warranty period is determined by purchase date given on your returned WARRANTY REGISTRATION FORM. Proof of purchase may be required. This Limited Warranty is extended only to the original purchaser of Danuser products.
