Datasheet

ManualsBrandsDANUBE ManualsPSU ComponentsDC/DC converter (print) 5 Vdc 5 Vdc 600 mA 3 W No. of outputs: 1 x

DANUBE

http://www.danube.com.tw

2010/06/15

18-1

FEATURES

z DUAL IN LINE PACKAGE

z UP TO 3W REGULATED OUTPUT POWER

z NO EXTERNAL COMPONENTS REQUIRED

z 100% BURN IN

z HIGH EFFICIENCY

z UL 94V-0 PACKAGE MATERIAL

z CUSTOM SOLUTIONS AVAILABLE

z 3 YEARS WARRANTY

OUTPUT SPECIFICATIONS INPUT SPECIFICATIONS

Voltage Set-point Accuracy +/-3% max Input Voltage Range +/-10% max

Temperature Coefficient +/-0.05%/°C Input Filter Pi Network

Ripple & Noise(20MHz BW)

100mVp-p max Protection Fuse Recommended

Line Regulation

+/-1% max

Load Regulation

+/-1% max

GENERAL SPECIFICATIONS

Minimum Load 10% of Full Load Efficiency 58% min

Short Circuit Protection Current Limit Protection Isolation Voltage

1500VDC min

Short Circuit Restart Automatic Isolation Resistance 10

ohms min

Transient Response

200uS max Isolation Capacitance 80pF max

Switching Frequency 50 KHz min

MTBF

>850,000 Hours

Weight 12.0g-14.4g

Case Material Non-Conductive Plastic

Or Five-Sided Shield Case

ENVIRONMENTAL SPECIFICATIONS

Case Size 31.8mm*20.3mm*10.2mm

Operating Temperature -25°C to +71°C Potting Material Epoxy(UL 94-V-0)

Storage Temperature -55°C to +125°C Conducted Emissions EN55022 Class A

Humidity 95% max Radiated Emissions EN55022 Class A

Cooling Free-Air Convection

ALL SPECIFICATIONS TYPICAL AT NOMINAL LINE, FULL LOAD AND 25

°C UNLESS OTHERWISE NOTED.

Measured with 1uF ceramic capacitor connect to the output pins.

High Line to Low Line.

Load Regulation is for output load current change from 10% to 100%.

For 10 seconds.

25% Step Load Change.

MIL-HDBK-217F @25 °C , Ground Benign.

CR SERIES

3W REGULATED

Summary of content (5 pages)

PAGE 1
CR SERIES 3W REGULATED FEATURES z z z z z z z z DUAL IN LINE PACKAGE UP TO 3W REGULATED OUTPUT POWER NO EXTERNAL COMPONENTS REQUIRED 100% BURN IN HIGH EFFICIENCY UL 94V-0 PACKAGE MATERIAL CUSTOM SOLUTIONS AVAILABLE 3 YEARS WARRANTY OUTPUT SPECIFICATIONS INPUT SPECIFICATIONS Voltage Set-point Accuracy +/-3% max Input Voltage Range +/-10% max Temperature Coefficient +/-0.
PAGE 2
z SELECTION GUIDE INPUT MODEL NUMBER 7 OUTPUT VOLTAGE VOLTAGE CURRENT (VDC) (VDC) INPUT8 OUTPUT (mA) CURRENT(mA) FULL NO LOAD LOAD EFF (%) 9 ISOLATION (VDC) CRS-0505(M) 4.5-5.5 5 600 960 85 63 1500 CRS-0509(M) 4.5-5.5 9 330 950 85 63 1500 CRS-0512(M) 4.5-5.5 12 250 930 85 64 1500 CRS-0515(M) 4.5-5.5 15 200 940 85 65 1500 CRS-0524(M) 4.5-5.5 24 125 910 92 66 1500 CRD-0505(M) 4.5-5.5 +/-5 +/-300 1110 85 54 1500 CRD-0512(M) 4.5-5.
PAGE 3
z SIMPLIFIED SCHEMATIC SINGLE OUTPUT DUAL OUTPUT REGULATOR +Vin REGULATOR +Vin +Vout OSCILLATOR DRIVER +Vout OSCILLATOR DRIVER Com. -Vout -Vout -Vin -Vin REGULATOR z MECHANICAL DIMENSIONS & RECOMMENDED FOOTPRINT DETAILS 20.3[0.80] 24 23 22 1 2 3 BOTTOM VIEW 15 14 13 SIDE VIEW 2.06[0.08] 31.8[1.25] 10 11 12 15.24[0.60] PIN SINGLE DUAL 1 & 24 +Vin +Vin 2 & 23 NC -Vout 3 & 22 NC Common 10 & 15 -Vout Common 11 & 14 +Vout +Vout 12 & 13 -Vin -Vin 10.2[0.40] 2.54[0.
PAGE 4
z TYPICAL PERFORMANCE CURVES Specifications typical at ta=25°C,nominal input voltage , rated output current unless otherwise specified. OUTPUT LOAD VS EFFICIENCY OUTPUT LOAD VS OUTPUT VOLTAGE OUTPUT VOLTAGE CHANGE(%) EFFICIENCY(%) 80% 60% 40% 20% 0% 0% 20% 40% 60% 80% 10% 5% 0% -5% -10% 100% 0% OUTPUT LOAD(%) 40% 60% 80% 100% OUTPUT LOAD(%) TEMPERATURE DERATING INPUT VOLTAGE VS EFFICIENCY 100% EFFICIENCY(%) 4.0 OUTPUT POWER(W) 20% 3.0 SAFE OPERATING AREA 2.0 1.
PAGE 5
CR SERIES APPLICATION NOTES: EXTERNAL CAPACITANCE REQUIREMENTS: No external capacitance is required for operation of the CR series. To meet the reflected ripple requirements of the converter, an input impedance of less than 0.5 ohm from DC to 100KHz is required. External output capacitance is not required for operation, however it is recommended that 10uF tantalum and 0.1uF ceramic capacitance be selected for reduced system noise.