USER / ARMORER MANUAL FOR ALL DANIEL DEFENSE® DD® WAVE® SUPPRESSORS & MUZZLE ADAPTERS 1
TABLE OF CONTENTS 1. DANIEL DEFENSE SUPPRESSOR SYSTEMS...................................3 2. ACME THREAD QUICK-CLAMPING SYSTEM QUICK REFERENCE....................................................................4 3. INCLUDED COMPONENTS...........................................................5 4. MUZZLE DEVICE INSTALLATION PROCEDURES WARNING ............................................................5 5. REMOVAL OF FACTORY FLASH HIDER AND CRUSH WASHER .............................................
2. ACME THREAD QUICK-CLAMPING SYSTEM QUICK REFERENCE DD WAVE properly installed ® ® OPEN: Rotate collar until it stops on the flat faces of the lock tabs. (FIGURE 1) ATTACH: Thread suppressor onto muzzle device adapter until clamps snap over the retaining flange on the muzzle device (you may feel some resistance, this is normal) and the suppressor is secured tightly. LOCK: Tighten locking collar against the locking tabs on the suppressor core.
5. REMOVAL OF FACTORY FLASH HIDER AND CRUSH WASHER FIGURE 3 1. Properly secure host weapon in a vise/fixture. Use of a reaction rod is recommended. 2. Insert combination wrench or crow’s-foot wrench (armorers tool) onto wrench flats of the birdcage flash hider to loosen. 3. Remove flash hider from barrel of host weapon. (Black arrow, FIGURE 3) 4. Remove and discard the factory-installed crush washer and any other shims/washers present. (Gray arrow, FIGURE 3) 5.1 CLEANING PROCEDURES 1.
3. Install and hand tighten muzzle device until snug. (Black arrow, FIGURE 5) 6. QUICK-CLAMPING SUPPRESSOR ATTACHMENT PROCEDURES 4. Insert combination tool that is attached to a torque wrench into wrench flats on the muzzle device. Wrench flats are 3⁄4” in width. OPEN: Rotate collar until it stops on the flat faces of the lock tabs. (FIGURE 1) 5. Use torque wrench set at 20-30 ft. lbs. and combination/ crow’s-foot wrench (armorers tool) to tighten suppressor adapter onto host weapon.
7. QUICK-CLAMPING SUPPRESSOR REMOVAL PROCEDURES 3. Use a clean cotton swab and a degreasing solution (acetone or alcohol is recommended) to remove residue/debris from the muzzle device threads. CAUTION! 4. Install beveled side of Daniel Defense alignment washer onto host weapon in the direction toward the barrel shoulder. Beveled side of spacer should face the barrel shoulder. DO NOT HANDLE SUPPRESSOR IMMEDIATELY AFTER IT HAS BEEN USED IN LIVE-FIRE OPERATIONS.
9. FIRING SCHEDULE WARNING! LIMIT FULL AUTO FIRING TO REDUCE HEAT BUILDUP AND EXTEND SUPPRESSOR LIFE. AVOID FIRING MORE THAN 90 ROUNDS OF SUSTAINED FIRE. IF THIS LIMIT IS REACHED, ALLOW THE UNIT TO COOL BEFORE RESUMING FIRE, IF POSSIBLE. HIGH-RATE FIRING BEYOND 120 ROUNDS CAN CAUSE COOK-OFF CONDITIONS. SHOULD THIS OCCUR, CLEAR STOPPAGES QUICKLY AND LEAVE THE CHAMBER EMPTY. 3. Inspect host weapon for any loose debris/residue that may have fallen into the barrel during this process.
length of the back section. Cuts shall be made completely through the tube forward of the back section/lock ring area. Shearing, crushing, deep water dumping, or smelting may be utilized when such methods of DEMIL are deemed cost effective or practicable, and when authorized by the appropriate authority or the DoD DEMIL Program Manager (DDPM). 12. SPECIFICATIONS Quick-clamping model: WEIGHT:.........................................17.2 oz LENGTH (w/COUPLING):...................7.6 in. COLLAR DIAMETER:....
101 WARFIGHTER WAY | BLACK CREEK, GA 31308 THIS DOCUMENT CONTAINS TECHNICAL DATA CONTROLLED UNDER THE INTERNATIONAL TRAFFIC IN ARMS REGULATIONS (ITAR). EXPORT AND/OR RELEASE FOR FOREIGN PERSONS REQUIRES PRIOR AUTHORIZATION FROM THE U.S. DEPARTMENT OF STATE. Rev D DANIELDEFENSE.