Fave o 1. M4 style two point advisability rear Iron sight 2. Innovation and highly efficiency Dual Core Integrated system (DC system. 3. High precision 3-D 'milled aluminum allay body and accents. Lol LAl BRI ST 5. Single finger:2 way adjustable spring return trigger [ e 7. Two separate length barrels: { 689x10Inch/13inch} 8.
EVERYTHING YOU NEED 10 GET STARTED Prepare the following items in order to begin using your M3-A1 : »:One 9V battery. Be sure that the battery is fresh and from a reputable manufacturer. «: Paintball Loading Devi's. { Recommended minimum load rate of 25 BPS Approved air tank utilizing COMPRESSED AIR or NITROGEN ONLY.
el tle SR8 DU B (Stepson. #: Screw counter clockwise to remove barrel from body.
LING A PRESET AIR SYSTEM vitiation, you must first rotate the rear sling loop in the outward fore from being in contact with the air sours. (PIC 04) the ASA twist knob o an appropriate distance. (PIC 05) rotate the tank upon installation, snd canning that it has been secured.
VELOCITY ADJUSTMENT »: Locate the alien key wrench included with your M3 At s Adjust screw locales at the sleds of the Operating Pressure Retaliatory (DPR) to Incense or L RRn Tum screw clockwise to decrease velocity.
Her = . are three adjustment screws (marked A, B) to adjust the trigger GLR Screw B less tha amount of rigger travel after the marker has been fired. Turing tha: sower clockwise will reduce the amount of trigger travel. Turing this screw counterclockwise: wiki Usl the scow far o the trigger will ba pushed past the firing point and the marker will ot work: ( .
FIRING MODE Firstborn per trigger pull. ‘Semi for the first 3 shots, then fully automatic on the 4th shot. " e Wuhan triggering pull spaded up to 8 BPS ramping will fum on at the & N maximum fire rate can adjust af the ROF. Baa SR Lignin L SOLENOID DWELL This value controls the allotted time (in milliseconds) the solenoid is open. If too low, the marker will cycle. if the values ls too high; the solenoid will remain pan tno long therefor decreasing balladry and ai el ABS DWELL Adds an additional.
ENGINEERS SUGGEST YOU ALWAYS USE DP-40 LUBE TO SERVICE YOUR MARKER DO NOT APPLY EXCESSIVE LUBRICANT . ALWAYS INSPECT AND CLEAN YOUR MARKER AFTER EACH USE NEVER APTLY EXCESSIVE FORCE WHEN REMOVING OR REPLACING SCREWS. DOING 80 MAY STRIP THE SCREW HEADS OR DAMAGE THREADS: ALWAYS USE THE CORRECT SZE AND THE APPROPRIATE TOOLS. REFRAIN FROM SUBMERGING ENTIRE MARKER IN LIQUID.
CLEANING THE EYE-SENSOR BREAK BEAN S5Y8 Using Allen wrench key, locate and remove both screws securing the eye sensor break beam system: (PIC 2900 Slung Allen wrench key, locates and remove both screws securing the aye-sensor system. g )] Remove tha aye-sensor system.
SRR BRI BILGE Reinstall aye sensor system in the reverse order of the removal (B careful ot 1 install wires in the yellow area to keep clear of the micro switch).
ING TRIGGER FROM FRAME jeer removal screw Usa (5/647) Allen key ranch to loosen and remove screw by muting jor assembly by fng it up and out of M3 A1 sager frame.
RAINING THE DCI SYSTEM front bolt housing by twisting the front piece counter clockwise to separate from the system.
Lim R 2l POWER™ warrants this M3-A1 paintball marker, to the Initial refill purchaser, 1o be free from defect in original materials and/or workmanship for waive( 12 ) months from the original fade of purchase, with T e 1. Disposable pairs { batteries, singsongs, seals, micro switch, air pressure: hose,rubber and/or plastic material par Electronic parts on this marker are fully warranted for 30 days from the longing date of purchase.
