A WORD FROM OUR ENGINEERS AND DESIGN TEAM OUR CHALLENGE WAS TO BLEND THE ART QF METAL SCULPTURE WITH MASTERFUL ELECTRONICS INA PACKAGE THAT SYMBOLIZES STRENGTH, POWER, AND DEXTERITY. BUILT WITH PASSION, THE DP G5 WAS UNLEASHED.
WARNINGS IMPORTANT SAFETY INSTRUCTIONS AND GUIDELINE 4. The DP G5 Is TOYOTA. Treat it with the same respect and care you would a firearm. the waning and guidelines printed in this Owner’'s Manual may result In property damage, injury or death. User assumes all risks associated with use of the marker. 3.
L2y 05 FEATURES 0f CONTENTS OF PACKAGE 57 KNOW YOUR G5 08 G5 PARTS LIST 03 INLINE REGULATOR kLl EVERYTHING YOU REED TO GET 1y 41 BARREL COVER LA ORE ATTACHING AIR TANK TO RAPS™ FLIP VELOCITY ADJUSTMENT BOARD PROGRAMMING YOUR 85 RN ELR SIRREE CARE AND MAINTENANCE Hierarchic i ey CLEANING THE EYE-SENSOR BREAK LR gd= ] CLEANING THE BALL DETERS MAINTENANCE DISASSEMBLY AND MAINTENANCE OF DUMP VALVE BOLT ARD BACK CAP SEPARATING GS BODY FROM Rile REMOVING TRIGGER FROM FRAME 44 RAPS™ FLIP LEVER ASA REMOVAL AND MAIN
FEATURES CONTENTS OF PACKAGE . O-inf less design with Innovative and highly efficient bolt system. . G5 Marker . Extremely light weight body (1.891bs with barrel and battery). . 13"/ .689 aluminum Auto Ocker barrel. . Increased air efficiency. . Barrel Sock .. High precision light weight 3-D milled aluminum alloy body and accents. . Ball end Allen key set . Stocked fully programmable micro-switch board. . Maintenance kit . 4:way adjustable magnet plus spring rectum ball bearing trigger.
KNOW YOUR G35 Your G5 is a sophisticated piece of machinery, designed for superior performance along with ease of use and maintenance. For maximum enjoyment and safety while using your G5, please take the time fo acquaint yourself with its operation, controls, programmable features, care and maintenance Instructions found In this Owner's Manual. PARTS LIST OPR (Operating Pressure Regulator) e 1T, V1R 1S AT oA Low-Rise Clamping Feed neck 1. Two-Way Solenoid pa L4 LG Electronic Board L.
INLINE REGULATOR G5 BOLT SYSTEM Operating Pressure Regulator Body . Bolt Body Bolt Bumper ool R .
EVERYTHING YOU NEED TO GET STARTED Prepare the following Items In order to begin using your Paintball loading device. {Recommended minimum load rate of 25 BPS) s Ways use fresh, high quantity paint with proper bore size .68 caber paintball for best result. ‘Approved air tank utilizing COMPRESSED AIR or NITROGEN ONLY. BARREL COVER ¢ Always use the supplied barrel cover before airing up your G5 when it is not in use at the field. Dong sc will help secure the safety of yourself and those around you.
INSTALLING THE BATTERY ATTACHING A PAINTBALL LOADER Carefully remove the 3 hexagonal scows holding the right grip panel In place. [DECELERATE 12T Loosen thumbscrew counterclockwise by hand. (BEE FIC B} Refer to the and for the Installation of the 9V battery. {SEE PIC B} Insert feed tube of loader unit. Laplace battery In grip frame as shown In illustration C. Do not use excessive force. Close clamp securely. Loader should fit snug within feed neck. {SEE FIC €} Laplace grip frame and screws.
ATTACHING AIR TANK TO RAPS™ FLIP LEVER ASA VELOCITY ADJUSTMENT Swing flip lever to the 'release’ potion. {SEE PIC A} ® Sea 1/8" Allen Key to adjust the velocity adjustment screw located at the bottom of the PPR, Attach air tank by carefully screwing it into the threaded portion of the RAPS™ ASA. Make * Tum screw counterclockwise to Increase veracity. sure tank fitment Is tight and all the way In. {SEE BIC 8} + Tum screw clockwise to decreases velocity.
TRIGGER ADJUSTMENT @ There are four adjustment screws (marked A, B, C and D) to adjust the trigger on the G5. ® Screw A adjusts the amount of trigger travel prior to the marker firing. Turing this screw clockwise will reduce the amount of trigger gravel. Turing this screw counterclockwise will Increases the amount of trigger travel. (SEE PIC A} Screw B (5/647) sets the amount of trigger travel after the marker has been fired. Turning the scow clockwise will reduce the amount of trigger travel.
BOARD Green light indicates battery level Is operational, Red light indicates battery level low. Programming mode cycles through SharePoint and enters set point values via rigger pulls. LRI LET POWER OFF Press and hold 2 seconds until R e “Tap to toggle eye sensor on/off. [ T Tt PROGRAMMING YOUR G5 RO POWER O # Press and hold down Button A to tum on the marker with TR TN ‘When battery voltage is lower than 7.2V, the indicator light will flash red. When battery voltage is over 7.
PROGRAMMING YOUR GS (continued) PROGRAMMING YOUR G5 (continue D) Dip Switch 1 set to “ON". Modes cannot be set without Sating Options as below: unlocking tournament lock. Red | Yellow B 110 IEE ki W CRED TG TEL PPN ] Green Flash h M 12/20 CONFIGURATION MODE Pull and hold down trigger then press Button A for 2 seconds. Release button A and then trigger and the Indicator light will flash multiple colors and stop at solid red which indicates programming mode.
PROGRAMMING YOUR GS (CONTINUED)} Liberia In Rate of Fire, pull the trigger 1 Time Indicate Increase 0.5 BPS, blow table can reference: [ T Tt PROGRAMMING YOUR GS (CONTINUED) FIRING MODE Fire 1 shot per tagger pull. Thea semi shots then transitions t 3 Rounds Burst, It rectums to sem mode lefter 1 second of no a activity. oL ‘Semi for the first 3 shots, then full automatic on the 4 pull and hold. Resetting to genii after 1 second of no activity. rigger pull speed lower than 7.
PROGRAMMING YOUR GS (CONTINUED)} RESET To rests the marker to manufacturing default settings, press and hold down the rigger then Press and hold down the on/off button. Release the on/off button and hold on to the trigger for 5 seconds until yellow light appears. 4. EXAMPLE SETTING FROM SEMI TO MILLENNIUM 1. Tum off the marker before entering the setting mode and switch dip 1 to the OFF position. 2::Pull and hold the trigger then press power button to tum on the marker.
CARE AND MAINTENANCE DEGASSING THE 85 Always be sure to completely DE-gas your marker before performing maintenance or service repair. Carefully follow the instructions below in sequence to ensure that all remaining air has been removed L Cur L TR . Flip the RAPS™ ASA to the ‘Off position. This disconnects the air system from the marker. . Remove the paintball ceding device and check to make sure there are no paintball within ALl . Unscrew the alr system from the RAPS™ ASA. .
(RPN The function of the break beam aye sensor Is to allow the firing circuit to ‘ime’ the activation of the solenoid. This prevents ‘chopping’ of paint, which is caused by the bolt Cycling within the breach without the paintball belong actually seated In the proper fining postilion. When the eye sensors are ON, the gun will not fire if the beam does not sensor a paintball.
CLEANING THE BALL DETENTES The ball detentes and spring should bs inspected during the cleaning of the eye sensors. Replace these parts should you notice any damage, no matter how slight. 1.7 Locate the eye cover plates on ether side of your G5 body. 2. Using provided Allen key wrench (5/647), carefully remove the eye cover screw on one ‘'side by inserting ball point tip and muting wrench handle counterclockwise. {SEE PIC &) 3. Lift eye cover plate, exposing eye wires, spring, and ball detente.
OPERATING PRESSURE REGULATOR (OPR) DISASSEMBLY AND MAINTENANCE The OPR regulates the amount of ale-flow. which determines paintball velocity. Regular Inspection and cleaning of your OPR is an sees part of peaking your G5 running in top condition. Follow the easy spats outlined blow to ensure that your OPR remains trouble-free. PRV direction. If the OPR unit is difficult to tum by hand, a rubber strap wrench available in most hardware stores may be used.
OPERATING PRESSURE REGULATOR (OPR) DISASSEMBLY AND MAINTENANCE (continue) 5. Using supplied Allen key wrench tum clockworks to remove Regulator Adjustment Screw. L 8. Remove all visible debris and dirt with a lightly dampened and clean cotton cloth. Do not scratch the surface of any regulator parts. 7. Lightly apply a small amount of DP-40 PLUS lubricant to the tip of a cotton swab.
DISASSEMBLY AND MAINTENANCE OF DUMP VALVE BOLT AND BACK CAP . Unscrew front of barrel from G5 body. . Use supplied Allen key wrench (1/47) and tum counterclockwise to unscrew back cap. (BEE MG A} A LIEN L SRR Remove Dump Valve Bolt from marker body. You may use your finger to push it out from the broach as illustrated. {SEE PIC C} . :\Wipe off all visible debris and grime from the Dump Valve Bolt, back cap and internal of G5 bad with a soft dampened cotton cloth and cotton swab.
SEPARATING G5 BODY FROM TRIGGER FRAME SEPARATING G5 BODY FROM TRIGGER FRAME {CONTINUED) 1. Carefully remove the 3 hexagonal screws holding the right grip panel In place. . Locate screw #1 underneath G5 body between OPR and Trigger Guard and screw #2 [ e behind the trigger frame. Using Allen key wrench, loosen Connecting Screw by muting it counterclockwise. (SEE PIC . D} 2.: Gently secure the base of the connectors and pull up to remove the plugs. DO SO ONE AT TIME.
The GS§ solenoid is a delicate electronic component that requires minimal maintenance or service. DP engineers do not recommend frequent maintenance of this part, or Its Internals. The following instructions are provided for reference and for expert technician only. . Using Allen wrench key, locate and remove both screws securing the solenoid to the 'Once both screws are removed, gently lift and remove the solenoid. {SEE PIC €} ..
REMOVING TRIGGER FROM FRAME . Locate the two trigger rectum spring plate screws Use (5/647) Allen key wrench to loosen and remove both screws by muting them counterclockwise. Be careful not to misplace the screws and trigger rectum spring. {SEE PiC Locate two trigger mounting screws and use Allen key wrench to loosen and remove scow by muting It counterclockwise. {SEE PIC €} . Remove trigger by lifting It up out of G5 trigger frame.
AND MAINTENANCE (continued) 3. Use a lightly dampened cloth and/or cotton swab to remove debris or grime from all RAPTNESS components, Including the piston, spring, lever, and casing. {SEE PIC [} 4.: Clean and Inspect o-ding located on the bees of the piston. Replace o-ring If It appears 'wom, cracked, or damaged. Using a cotton swab, apply a small amount of DP-40 PLUS lubricant on the o-ring. {SEE PIC E} 5.
will not turn on Lo et Hold down operating button for more than 4 seconds e e FOOTY AT Y barrel area Clean the battery touch panel from PC board G5 will not fire Low battery power L g Paintball breaking out of the barrel ey e The stock barrel size ia .
The manufacturer assumes no responsibility for this product’s sale or distribution. PROPERTY DAMAGE, BODILY INJURY, OR DEATH could occur due to misuse, abuse or failure to follow the manufacturer's Instructions stated In this manual. The manufacturer will assume no responsibility for physical injury or property damage resulting from the use of this marker. The information in this document is subject to change without prior notice.
