Operating instructions

VLT
®
5000 FLUX
Mains failure ............................................................... 92
Mains fault
.................................................................108
Mains Interference
........................................................... 8
Mains supply
..............................................................146
Mains supply (L1, L2, L3):
..............................................140
Max motor speed
......................................................... 81
Maximum Inertia
........................................................... 77
Maximum reference
.................................................. 82, 82
Mechanical brake
.......................................................... 86
Mechanical dimensions
.................................................. 13
Mechanical installation ................................................... 16
Menu mode
................................................................ 47
Minimum Intertia
........................................................... 77
Minimum reference................................................... 81, 81
Minor Interference on Mains
.............................................. 8
Miscellaneous
................................................................ 6
Moment of inertia.......................................................... 76
Motor
...........................................................................6
Motor cables
............................................................... 36
Motor connection ......................................................... 19
Motor current
.......................................................... 86, 87
Motor current
.............................................................. 63
Motor frequency ........................................................... 70
Motor Parameters
......................................................... 76
Motor power
................................................................ 69
Motor Protection........................................................9, 19
Motor shaft direction
...................................................... 19
Motor thermal protection
................................................ 19
Motor voltage............................................................... 64
Multi-references
............................................................ 53
N
Nameplate data....................................................... 69, 70
Normal-constant torque
................................................. 69
Normal/high overload torque control
.................................. 59
O
Operating hours,..........................................................117
Operating mode
..........................................................119
Operation mode ..........................................................119
Output
.........................................................................5
Output speed range/Direction
.......................................... 81
Output speed............................................................... 81
Overvoltage control
......................................................104
P
proportional gain..........................................................107
Parameter groups
......................................................... 47
Parameter setup keys:
................................................... 44
Phase loss
.................................................................. 87
Phase Loss Monitor
....................................................... 87
PLC
........................................................................... 40
Pole number
........................................................... 77, 77
Potentiometer reference
................................................. 35
Power
................................................................... 63, 63
Power monitoring,
........................................................105
Power up
.................................................................... 66
Pre-heat
..................................................................... 73
Pre-magnetizing
........................................................... 72
Preset reference
........................................................... 85
Preset reference, on
...................................................... 91
Programmable Signal Outputs
...........................................8
Programming Setup ...................................................... 62
Pulse reference
....................................................... 64, 92
Pulse start/stop
............................................................ 34
Q
Quick menu mode ........................................................ 46
Quick Menu parameter
................................................... 47
Quick menu, userdefined
................................................ 66
Quick Setup via Quick menu
........................................... 47
Quick stop
.................................................................. 83
Quick-stop
...................................................... 90, 90, 111
R
ramp-up time. .............................................................. 82
Reference .............................................................. 63, 81
reset
.........................................................................105
Ramp 2
...................................................................... 92
Ramp type .................................................................. 82
Ramp type,
................................................................. 82
Ramp-down time
..................................................... 82, 82
Ramp-down time. ......................................................... 83
Ramp-up time
.............................................................. 82
Rated motor speed
....................................................... 70
RCD .......................................................................... 23
Read-outstate
............................................................. 46
Reference
.............................................................. 63, 93
Reference function ........................................................ 83
References
..........................................................6, 83, 85
Relay outputs:
......................................................142, 142
Reset .................................................................... 90, 90
Reversing
..............................................................91, 112
RFI switch
................................................................... 41
Rotor Leakage Reactance .............................................. 76
Rotor resistance
........................................................... 76
RS 232
....................................................................... 33
RS 485....................................................................... 32
S
Safety earthing ............................................................. 19
Safety regulations
...........................................................4
Saturation brake
..........................................................108
Scaling
......................................................................100
MG.55.A7.02 - VLT is a registered Danfoss trademark
160