Installation Guide Danfoss ECtemp Touch Electronic Intelligent Timer Thermostat electricheating.danfoss.
Danfoss ECtemp Touch Table of Contents 1 Introduction ���������������������������������������������������������������� 2 1.1 Technical Specifications ���������������������������������� 3 1.2 Safety Instructions ������������������������������������������� 5 2 Mounting Instructions ������������������������������������������� 6 3 Settings ������������������������������������������������������������������������� 9 3.1 Initial Settings ���������������������������������������������������� 9 3.
Danfoss ECtemp Touch • An installation wizard with room/floor type-specific setup. • Support for multiple frame systems. • Compatible with several 3rd party NTC sensors. • Thermostat settings can be specified before installation and imported to the thermostat using a web-generated code, or copied from a thermostat in a similar installation. • Smart access to thermostat settings after installation by using a web code interface for easy setup or remote troubleshooting.
Danfoss ECtemp Touch 4 Sensing values: (Default NTC 15 K) 0°C 20°C 50°C 42 kΩ 18 kΩ 6 kΩ Control PWM (Pulse Width Modulation) Ambient temperature 0° to +30°C Frost protection temperature 5°C to +9°C (default 5°C) Temperature range Room temperature: 5-35°C. Floor temperature: 5-45°C. Max. floor: 20-35°C (if unrecoverable seal is broken then up to 45°C). Min. floor: 10-35°C, only with combination of room and floor sensor.
Danfoss ECtemp Touch IP class 21 Protection class Class II - Dimensions 85 x 85 x 20-24 mm (in-wall depth: 22 mm) Weight 103 g Electrical safety and Electro-Magnetic Compatibility for this product is covered by the compliance with the EN/IEC Standard “Automatic electrical controls for household and similar use”: • EN/IEC 60730-1 (general) • EN/IEC 60730-2-9 (thermostat) 1.2 Safety Instructions Make sure the mains supply to the thermostat is turned off before installation.
Danfoss ECtemp Touch • The thermostat must be connected to a power supply via an all-pole disconnection switch. • Always connect the thermostat to continuous power supply. • Do not expose the thermostat to moisture, water, dust, and excessive heat. 2 Mounting Instructions Please observe the following placement guidelines: Place the thermostat at a suitable height on the wall (typically 80-170cm.). The thermostat should not be placed in wet rooms. Place it in an adjacent room.
Danfoss ECtemp Touch Do not place the thermostat in a way that it will be exposed to direct sunlight. Note: A floor sensor enables a more accurate temperature control and is recommended in all floor heating applications and mandatory under wooden floors to reduce the risk of over-heating the floor. • Place the floor sensor in a conduit in an appropriate place where it is not exposed to sunlight or draft from door openings. • Equally distant and >2cm from two heating cables.
Danfoss ECtemp Touch Follow the steps below to mount the thermostat: 1. Open the thermostat: Important: Do NOT press on the display screen when removing the front part. Press your fingers under the side of the front part and pull toward you: 2. Connect the thermostat according to the connection diagram. NTC L L N N Sensor L O A D Maximum Load 16 (1) A L O A D Mains 220-240V 50-60 Hz IP21 T30 Dtouch Standby maximum 0.
Danfoss ECtemp Touch 3. Mount and reassemble the thermostat. • Fasten the thermostat to a socket or an exterior wall box by driving the screws through the holes in each side of the thermostat. • Put the frame on. • Click the display module back in place. Important: Do NOT press on the display screen when clicking the display module back in place. Initially main supply the thermostat for 15 hours to fully charge the battery. The current time and day is then kept for 24 hours if mains supply is off.
Danfoss ECtemp Touch 10 1. Use the arrows in the right side of the screen to go to your language, and press to select it. Then press in the upper right corner to confirm. 2. Press the hour numbers and use the < and > arrows to set the hour. Press to confirm. 3. Press the minutes numbers and use the < and > arrows to set the minutes. Press to confirm. Press again to go to the SET DATE screen. 4.
Danfoss ECtemp Touch 5. If you have already made the installation setup online, press ENTER CODE and go directly to Step 13 now. Otherwise press SETUP WIZARD and go to Step 6. 6. On the SETUP information screen, press to start. 7. Use the < and > arrows to select whether only a floor sensor or a combination of room and floor sensors should be used. Press to confirm. Note: A “room only” option may also be available. For details, see the “Maximum Floor Temperature” section.
Danfoss ECtemp Touch 8. Use the < and > arrows to select the installed floor sensor type. (Measured resistance and corresponding temperature are shown in brackets). Press to confirm. 9. Use the < and > arrows to select the flooring type. Press to confirm. 10. Use the < and > arrows to select the room type. Press to confirm. 11. Use the < and > arrows to select the approximate load of the heating element. If an external relay is used or the installed output is unknown, select the “– –” option.
Danfoss ECtemp Touch 12. Use the < and > arrows to select whether the timer should be activated or not. Press to confirm and end the initial thermostat setup. Skip Step 13. 13. Enter your web-generated code. Then press to end the initial thermostat setup. If no check mark ( ) appears, the hexacode is incorrect. 3.2 Forecast The forecast feature is used when you switch between economy temperature and comfort temperature.
Danfoss ECtemp Touch How to turn the forecast feature on and off. 1. Touch the thermostat display to activate it, then press menu. 2. Press SETTINGS in the bottom right corner of the menu. Then press OPTIONS. 3. Press FORECAST. Then press ON to optimise heating start/ stop or OFF to simply let the heating start/stop at the specified time. Press to confirm.
Danfoss ECtemp Touch 3.3 Window Open How to turn “window open detection” on or off 1. Touch the thermostat display to activate it, then press menu. 2. Press SETTINGS in the bottom right corner of the menu. Then press OPTIONS. 3. Press WINDOW OPEN. Then press ON to temporarily turn off heating in case of a sudden temperature drop in the room or OFF to let the thermostat heat during sudden temperature drops in the room. Press to confirm.
Danfoss ECtemp Touch 3.4 Maximum Floor Temperature How to set the maximum floor temperature 1. Touch the thermostat display to activate it, then press menu. 2. Press SETTINGS in the bottom right corner of the menu. Then press INSTALLATION and MANUAL SETUP. 3. Press MAX. FLOOR. Then use the < and > arrows to set the allowed maximum floor temperature. Press to confirm.
Danfoss ECtemp Touch If you break the small plastic seal on the back of the display module, e.g. using a screwdriver, it will be possible to set the maximum floor temperature up to 45°C. Furthermore, it will be possible to use only a room sensor. However, this option is not recommendable due to an increased risk of overheating the floor.
Danfoss ECtemp Touch Thermal resistance [m2K/W] Examples of flooring Details Approximate setting for 25˚C floor temperature 0.05 8 mm HDF based laminate > 800 kg/m3 28˚C 0.10 14 mm beech parquet 650 - 800 kg/m3 31˚C 0.13 22 mm solid oak plank > 800 kg/m3 32˚C < 0.17 Max. carpet thickness suitable for floor heating acc. to EN 1307 34˚C 0.
Danfoss ECtemp Touch Symbol What it means An away period has been planned. On the date of departure, the away period starts at 00:00 and the specified away temperature will be maintained 24 hours a day until the date of return at 00:00. At this time the normal temperature settings will resume. An error has occurred. If you press the warning symbol, more information on the error will appear.
Danfoss ECtemp Touch 20 Installation Guide
Danfoss ECtemp Touch Installation Guide 21
Danfoss ECtemp Touch 22 Installation Guide
Danfoss ECtemp Touch Danfoss A/S Electric Heating Systems Ulvehavevej 61 7100 Vejle Denmark Phone: +45 7488 8500 Fax: +45 7488 8501 http://electricheating.danfoss.com/ Danfoss can accept no responsibility for possible errors in catalogues, brochures and other printed material. Danfoss reserves the right to alter its products without notice.
dMA Design Frame Intelligent Timer Thermostat Floor / Room Sensor 220-240V~ 50-60Hz 0°C to +30°C 16A/3680W@230V~ IP 21 088L0122 EN 21,7 ECtemp Touch - Pure White 5 703466 235485 Designed in Denmark for Danfoss A/S Product documentation *08091366*
