Installation guide

8 Installation guide RI8BP602 © Danfoss 10/2011 AKM/AK Monitor/AK Mimic
Printouts
1 Define whether printouts of alarms must be made by the printer
when the alarms are received.
2 Define whether a printout should be made when an alarm is
accepted.
3 Define whether a printout will be required when a setpoint is
changed for a controller (when the change takes place from the
programme).
4 Define whether the printer is to provide a printout when the
programme is started and at Logon and Logoff.
System Setup / Language
Select the language required for showing the various menu
displays. If you change to another language after the installation,
the new language will not appear until the programme is
restarted.
Start the AKM programme through the PC
Define whether the programme is to be started automatically
when the PC is switched on (booted, or when it starts up again
after a power failure).
Alarm
1 Decide if the PC is to give a signal (beep), when an alarm is
received.
2 Select duration in seconds (beep time).
3 Select how many days an alarm should be shown on the alarm
list. Only accepted alarms will be deleted from the list when
the time is up. This time-limit also applies to the contents of the
event register “AKM Event Log”.
Log
1. The “Use callback” must be used, if the log function in the
programme is to collect log data from a front-end, which is
connected with a modem. The programme calls the system,
and activate call back, and then immediately interrupts the
telephone connection. A call is now made by the system which
consequ ently pays for the data transmission.
2 The “Form feed before auto printer” function is used, if the log
printout is to start on a new page when log data are printed
automatically.
(If an alarm has started between two log printouts, the alarm
message and the log printouts can be kept on separate pages).
Optimize communication
The Plant overview communicates constantly with all controllers in
relation to the values to be displayed. A pause time can be set here
before further communication with the controllers.
Button for Print
A push will provide a printout of the set values in this display.
Button for Advanced
Gives access to special functions that should only be set by
specially trained persons. In the display shown assistance can be
obtained by pushing the “?” key.
Log collect
Normally transfer of logs takes place automatically when the
amount of data reaches a certain size. But if you prefer to have
transfers of logged data carried out at a specified time, whatever
the amount of them, you must set this function.
- Set time outside of normal working hours when the telephone
rates may be lower.
- There will be a daily collection of logs, although it is possible
to set a specific weekday.
- When a collection from a destination takes place, the system
proceeds to the next but only after the delay time has expired.
The delay time is there to prevent alarms from being blocked.
- Indicate if the plant is to be disconnected when the log collec-
tion is complete.
- The collected logs are stored in the computer's RAM until all
destinations have been retrieved. It is then transferred to the
hard drive. Indicate if the log is to be transferred after each
destination.
Log Data History Clean-up
- Set a time when the computer is not overloaded.
- Select which setting is to be used. Either the one set in the
AKA or the one set here in the AKA programme.
Remote communication
Indicate if the AKM should show the telephone number of the
destination for the next planned call.
Screen saver
- Define whether the screen saver is always to be activated
when the programme is started. Or whether it should only
happen when the programme is waiting for a “Logon”. The
screen saver can be cancelled by meas of the "AKM Setup -
Advanced"
- Set the time that is to elapse before the screen saver is acti-
vated.
- Indicate if an access code is necessary for access after an ac-
tive screen saver.
Timeout
- DANBUSS® time out. If the plant is disconnected for longer
than set, a communication alarm signal will sound.
- Remote Timeout. If there is a pause in communication to the
external unit via "Plant Archive" for longer that the set time,
the system will disconnect.
- AKA Password Timeout in the gateway. An access code will be
required if there is a pause in operation longer than the set
time.
Alarm
- If a connection defined in the Alarm Scheme cannot be made,
a repeat routine will be initiated in order to make contact. Set
the number of repeats. The alarm will then appear.
- Indicate whether the alarms should appear as pop-ups on the
screen in separate dialogue boxes.
Any later changes in the “AKM Setup” menu can be made via:
“Configuration” - “AKM Setup...”.
The programme has now been installed on your PC.